Eliminate duplicate code by refactoring the calls to qla2xxx_read_sfp()
in qla2x00_get_thermal_temp(). This keeps the parameter values separate
from the mailbox register mechanics. This also allows qla2xxx_read_sfp()
to be the sole "spec" for READ SFP semantics.

Signed-off_by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Make the read/write sfp mailbox command routines uniform, and remove redundancy.
Also protect against attempting to do a single byte dma in these routines.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Use proper init_cb_size member which takes into account
MID/non-MID init-cb structure sizes.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The 'max_lun' value registered for each scsi_host is currently
capped at 0xffff.  The new module parameter can allow for
2nd-level flat-space addressing method-infrastructure to be
supported.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When reading a single byte using the READ SFP mailbox command, the
single byte of data is returned in MB[1] and not MB[8].

The reason that MB[8] was being used is that the spec was unclear
as it evolved over time; and we have not needed to read a single
byte until recently.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Encapsulate the unlocking of the ROM lock in a function for better
code readability.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The debug print prints the first byte of the buffer which is buf[8].
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The driver keeps a copy of the fw_version within the ha structure.
For ISP82xx, this local copy doesn't get updated, and as a result,
the old firmware version ends up getting displayed. This patch fixes
this issue.
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Bumping ref count during fc_vport_terminate() was the cause. vport
delete would wait for ref count to drop to zero and that would never
happen.

Cc: stable@kernel.org
Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The firmware spec has the fcp_data_dseg_len defined as a 32-bit
value, while the corresponding field in the driver structure has
it defined as a 16-bit value.

Cc: stable@kernel.org
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch ensures qla82xx_watchdog is not being run for the vport. It also
makes sure that beacon ON is not done for the vport, as it will lead to the
waking up of the dpc thread again and again.
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Timer is required to flush out entries that may be present in work queues.

Cc: stable@kernel.org
Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

A minor change in the versioning. We'll be attaching the "-k"
in the end.
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add the inline function qla2x00_set_port_state() so that when a fcport state
transition happens we can log the state transition if debug messages are
enabled.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Before driver's own internal state is marked as PLOGI/PRLI
complete. This additional check closes a window seen with
dual-personality initiator/target devices where a driver's
PLOGI/PRLI request occurs within the window after the target's
PLOGI request has completed, but prior to the target's PRLI
arriving and processed by the firmware. Without this additional
check, the firmware will return port-information stating that the
port neither supports target nor initiator functions, causing the
driver to register the rport prematurely to the FC-transport
without the proper 'roles' being set.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Also, change the ISP82xx code to only reset if this module_param is set
and reset is intended via the QLA82XX_DEV_NEED_RESET case.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Display hardware/firmware registers to get more information about the error for ISP82xx.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If fabric device has invalid loop id (FC_NO_LOOP_ID) then call
qla2x00_find_new_loop_id() to attempt to obtain valid loop id.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

For certain failures, try to recover first by doing FCoE context reset before
attempting big hammer approach(adpater reset).
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The stanadlone call to qla82xx_check_fw_alive() in qla82xx_watchdog()
is a typo, so remove it.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Include request queue ID in the upper 16-bits of the I/O handle for Abort I/O IOCBs.

The upper 16-bits of the handle for all I/O in multi-queue supported
drivers carries the ID of the request queue it was submitted on. When
using Abort I/O IOCB, the driver needs to also populate the upper
16-bits in the handle_to_abort field so the fw can correlate with the
actual I/O.
Signed-off-by: NMike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The bit is already set upon entry.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Modifying qla24xx_get_fcp_prio() to return a 'found' status
allows the driver to short circuit the 'set FCP-priority' call
and reduce the amount of noise generated in the messages file:

	scsi(5): Unable to activate fcp priority,  ret=0x102
	scsi(5): Unable to activate fcp priority,  ret=0x102

Also make qla24xx_get_fcp_prio() static.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The respective done() functions are called from process context,
so there's no reason to 'defer' the request.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

To provide a clearer translation of the command-status origin in
relation to the midlayer's standard SCSI nexus.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

We'll be using the new version number scheme from now on.
The 'k' in the version in the past will be removed.

The format will be: <major>.<minor>.<sub_minor>.<iter>
A scsi-misc submission increments <sub_minor> and resets <iter>.
An scsi-rc-fixes submission, increments <iter>.
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The fc_block_scsi_eh() might return with status FAST_IO_FAIL
indicating I/O has been terminated due to fast_io_fail timeout.
In this case the rport is still blocked, so any error recovery
will be failing on this port. Hence we need to check if the
return value from fc_block_scsi_eh() is something other than 0,
in which case it should just return with that status.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If adapter is not online, the driver will not process the response queue, even
on getting an interrupt.
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Based on reading of the FCP2/4 specification, the driver cannot
expect the storage device to send FCP_RSP information. Instead,
the driver should interpret the data which is present in the frame
to base decisions on the success or failure of the system.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

By not clearing the 'login needed' nor 'login outstanding' states
for an fcport after a big-hammer (adapter reset), the driver may
not properly perform a PLOGI/PRLI sequence (and lose visibility
to the rport) during a follow-on SNS scan.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>