I've picked hdmi as the first encoder to convert because it's rather
simple:
- no cloning possible
- no differences between prepare/commit and dpms off/on switching.

A few changes are required to do so:
- Split up the dpms code into an enable/disable function and wire it
  up with the intel encoder.
- Noop out the existing encoder prepare/commit functions used by the
  crtc helper - our crtc enable/disable code now calls back into the
  encoder enable/disable code at the right spot.
- Create new helper functions to handle dpms changes.
- Add intel_encoder->connectors_active to better track dpms state. Atm
  this is unused, but it will be useful to correctly disable the
  entire display pipe for cloned configurations. Also note that for
  now this is only useful in the dpms code - thanks to the crtc
  helper's dpms confusion across a modeset operation we can't (yet)
  rely on this having a sensible value in all circumstances.
- Rip out the encoder helper dpms callback, if this is still getting
  called somewhere we have a bug. The slight issue with that is that
  the crtc helper abuses dpms off to disable unused functions. Hence
  we also need to implement a default encoder disable function to do
  just that with the new encoder->disable callback.
- Note that we drop the cpt modeset verification in the commit
  callback, too. The right place to do this would be in the crtc's
  enable function, _after_ all the encoders are set up. But because
  not all encoders are converted yet, we can't do that. Hence disable
  this check temporarily as a minor concession to bisectability.

v2: Squash the dpms mode to only the supported values -
connector->dpms is for internal tracking only, we can hence avoid
needless state-changes a bit whithout causing harm.

v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just prep work, not yet put to some use.

Note that because we're still using the crtc helper to switch modes
(and their complicated way to do partial modesets), we need to call
the encoder's disable function unconditionally.

But once this is cleaned up we shouldn't call the encoder's disable
function unconditionally any more, because then we know that we'll
only call it if the encoder is actually enabled. Also note that we
then need to be careful about which crtc we're filtering the encoder
list on: We want to filter on the crtc of the _current_ mode, not the
one we're about to set up.

For the enabling side we need to do the same trick. And again, we
should be able to simplify this quite a bit when things have settled
into place.

Also note that this simply does not take cloning into account, so dpms
needs to be handled specially for the few outputs where we even bother
with it.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since it's redundant - we can get the attached encoder in the
functions themselves.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For reasons that are not apparent to anybody, 990bbdad (drm/i915:
Group the GT routines together in both code and vtable) breaks the use
of the BitStream Decoder ring on SandyBridge. The active ingredient of
that patch is the conversion from a udelay(10) to a udelay(1) in the
busy-wait loop of waiting for the forcewake acknowledge. If we restore
that udelay(10) or insert another udelay(1) afterwards (or any wait
longer than 250ns) everything works again. An alternative is also to
remove any delay from the busy-wait loop.

Given that in the atomic sections we want to complete the wait as quick
as possible to avoid blocking the CPU for too long, it makes sense to
remove the delay altogether and simply spin on the exit condition until
it completes. So we replace the udelay(1) with cpu_relax().

Papers over regression from

commit 990bbdad
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Mon Jul 2 11:51:02 2012 -0300

    drm/i915: Group the GT routines together in both code and vtable

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51738Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function isn't used outside of intel_panel.c, so make it static.
Signed-off-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We believe to have squashed all issues around the gen6+ rps interrupt
generation and why the gpu sometimes got stuck. With that cleared up,
there's no user left for the sanitize_pm infrastructure, so let's just
rip it out.

Note that 'intel_reg_write 0xa014 0x13070000' is the w/a if we find
ourselves stuck again.
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As suggested by Daniel, rip out the independent timers for device and
crtc busyness and integrate the manual powermanagement of the display
engine into the GEM core and its request tracking. The benefits are that
the code is a lot smaller, fewer moving parts and should fit more neatly
into the overall activity tracking of the driver.

v2: Complete overhaul and removal of the racy timers and workers.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will be needed for Haswell, but already has its uses here.

This patch started as a small patch written patch by Shobhit Kumar,
but it has changed so much that none of its original lines remain.

Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of having a giant if cascade to figure this out according to
the passed-in register. We could do quite a bit more cleaning up and
all by using the port at more places, but I think this should be part
of a bigger rework to introduce a struct intel_digital_port which
would keep track of all these things. I guess this will be part of
some haswell-DP-induced refactoring.

For now this rips out the big cascade, which is what annoyed me so
much.

v2: Add port variable name back for the func decl (I've tried to trick
myself below the 80 char limit).
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Intel hw only has one MUX for encoders, so outputs are either not
cloneable or all in the same group of cloneable outputs. This neatly
simplifies the code and allows us to ditch some ugly if cascades in
the dp and hdmi init code (well, we need these if cascades for other
stuff still, but that can be taken care of in follow-up patches).

Note that this changes two things:
- dvo can now be cloned with sdvo, but dvo is gen2 whereas sdvo is
  gen3+, so no problem. Note that the old code had a bug and didn't
  allow cloning crt with dvo (but only the other way round).
- sdvo-lvds can now be cloned with sdvo-non-tv. Spec says this won't
  work, but the only reason I've found is that you can't use the
  panel-fitter (used for lvds upscaling) with anything else. But we
  don't use the panel fitter for sdvo-lvds. Imo this part of Bspec is
  a) rather confusing b) mostly as a guideline to implementors (i.e.
  explicitly stating what is already implicit from the spec, without
  always going into the details of why). So I think we can ignore this
  - worst case we'll get a bug report from a user with with sdvo-lvds
  and sdvo-tmds and have to add that special case back in.

Because sdvo lvds is a bit special explain in comments why sdvo LVDS
outputs can be cloned, but native LVDS and eDP can't be cloned - we
use the panel fitter for the later, but not for sdvo.

Note that this also uncoditionally initializes the panel_vdd work used
by eDP. Trying to be clever doesn't buy us anything (but strange bugs)
and this way we can kill the is_edp check.

v2: Incorporate review from Paulo
- Add in a missing space.
- Pimp comment message to address his concerns.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move the DP structure to shared location so that it can be used from
within the ddi module.

Changes from Paulo:
- Move less code to intel_drv.h
- Remove #include statement
- Replace a tab with a space in train_set
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have way too much lying hardware to rely on a simple "does someone
answer on the ddc i2c address?" check. And now it's unused, so just
kill it.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This initializes power wells within the modeset_init_hw routine.
Testing has shown that this works for both driver load time and for
suspend-resume code paths.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To avoid recomputing the display framebuffer offset on gen2/3
pageflips. This is also prep work to do similar trickery on gen4+

Also:
- kill "Start", such upper-case remnants from the ddx must surely die.
- rename "Offset" to linear_offset, to make it clearer that on gen4+
  this is only used by the hw for linear buffers, for tiled buffers it
  uses the TILEOFF register.
- call DSAPADDR DSPLINOFF on gen4+ for the same reason (and because
  the documentation really renamed the register).
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While creating the new enable/disable_gt_powersave functions in

commit 8090c6b9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sun Jun 24 16:42:32 2012 +0200

    drm/i915: wrap up gt powersave enabling functions

I've botched up the handling of ironlake_disable_rc6. Fix this up by
calling it at the right place. Note though that ironlake_disable_rc6
does a bit more than just disabling rc6 - it also tears down all the
allocated context objects.

Hence we need to move intel_teardown_rc6 out and directly call it from
intel_modeset_cleanup.

Also properly mark ironlake_enable_rc6 as static and kill the un-used
declaration in i915_drv.h.

Note: In review a question popped out why disable_rc6 also tears down
the backing object and why we should move that out - it's simply for
consistency with gen6+ rps code, which does it that way.

Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This commit moves force wake support routines into intel_pm modules, and
exports the gen6_gt_check_fifodbg routine (used in I915_READ).
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of calling each one for each generation indiviudally.

Notice that we've already managed to be inconsistent, the resume path
is missing an IS_VLV check. As a nice benefit we can mark all the
platform specific enable/disable functions as static and hide them in
intel_pm.c
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we switch on/off the primary plane if it is completely obscured by an
overlapping video sprite, we also nee to make sure that we update the
FBC configuration at the same time.

v2: Not all crtcs are intel_crtcs, as spotted by Daniel.
v3: Boot testing rules.

References: https://bugs.freedesktop.org/show_bug.cgi?id=50238Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On gen4+ we have a bitfield to specify from which pipe the backlight
controller should take it's clock. For PCH split platforms we've
already set these up, but only at initialization time. And without
taking into account the 3rd pipe added with ivb.

For gen4, we've completely ignored these. Although we do restrict lvds
to the 2nd pipe, so this is only a problem on machines where we boot
up with the lvds on the first pipe.

So restructure the code to enable the backlight on the right pipe at
modeset time.

v2: For odd reasons panel_enable_backlight gets called twice in a
modeset, so we can't WARN_ON in there if the backlight controller is
switched on already.

v3: backlight enable can also be called through dpms on, so the check
in there is legit. Update the comment to reflect that.
Tested-By: NKamal Mostafa <kamal@canonical.com>
Bugzilla: https://bugs.launchpad.net/bugs/954661
Cc: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should only frob adjusted_mode. This is in preparation of
a massive patch by Laurent Pinchart to make the mode argument
const.

After the previous two prep patches the only thing left is to clean up
things a bit. I've opted to pass in an adjust_mode param to
dp_adjust_dithering because that way we can be sure to avoid
duplicating this logic between mode_valid and mode_fixup - which was
the cause behind a dp link bw calculation bug in the past.

Also mark the mode argument of pch_panel_fitting const.

v2: Split up the mode->clock => adjusted_mode->clock change,
as suggested by Chris Wilson.
Reported-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.

The next patch will stop us from modifying mode->clock.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need a function that is able to fully 'set' the state of the DIP
registers to a known state.

Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.

This patch only adds the infrastructure keeping the code behavior the
same as before.

v2: add static keywords
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At least the worst offenders:
- SDVO specifies that the encoder should compute the ecc. Testing also
  shows that we must not send the ecc field, so copy the dip_infoframe
  struct to a temporay place and avoid the ecc field. This way the avi
  infoframe is exactly 17 bytes long, which agrees with what the spec
  mandates as a minimal storage capacity (with the ecc field it would
  be 18 bytes).
- Only 17 when sending the avi infoframe. The SDVO spec explicitly
  says that sending more data than what the device announces results
  in undefined behaviour.
- Add __attribute__((packed)) to the avi and spd infoframes, for
  otherwise they're wrongly aligned. Noticed because the avi infoframe
  ended up being 18 bytes large instead of 17. We haven't noticed this
  yet because we don't use the uint16_t fields yet (which are the only
  ones that would be wrongly aligned).

This regression has been introduce by

3c17fe4b is the first bad commit
commit 3c17fe4b
Author: David Härdeman <david@hardeman.nu>
Date:   Fri Sep 24 21:44:32 2010 +0200

    i915: enable AVI infoframe for intel_hdmi.c [v4]

Patch tested on my g33 with a sdvo hdmi adaptor.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=25732
Tested-by: Peter Ross <pross@xvid.org> (G35 SDVO-HDMI)
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell, we need to properly train the DDI buffers prior to enabling
HDMI, and enable the required clocks with correct dividers for the desired
frequency.

Also, we cannot simple reuse HDMI routines from previous generations of
GPU, as most of HDMI-specific stuff is being done via the DDI port
programming instead of HDMI-specific registers.

This commit take advantage of the WR PLL clock table which is in a
separate (previous) commit to select the right divisors for each mode.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move intel_hdmi data structure and support functions to a shared location,
to allow their usage from intel_ddi module.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Digital port detection on Haswell is indicated by the presence of a bit in
DDI_BUF_CTL for port A, and by a different register for ports B, C and D.
So we check for those bits during the initialization time and let the hdmi
function know about those.

Note that this bit does not indicates whether the output is DP or HDMI.
However, the DDI buffers can be programmed in a way that is shared between
DP/HDMI and FDI/HDMI except for PORT E.

So for now, we detect those digital outputs as being HDMI, but proper DP
support is still pending.

Note that DDI A can only drive eDP, so we do not handle it here for hdmi
initialization.

v2: simplify Haswell handling logic

v3: use generic function for handling digital outputs.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The line time can be programmed according to the number of horizontal
pixels vs effective pixel rate ratio.

v2: improve comment as per Chris Wilson suggestion

v3: incorporate latest changes in specs.

v4: move into wm update routine, also mention that the same routine can
program IPS watermarks. We do not have their enablement code yet, nor
handle the required clock settings at the moment, so this patch won't
program those values for now.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Starting with Haswell, DDI ports can work in FDI mode to support
connectivity with the outputs located on the PCH.

This commit adds support for such connections in the intel_ddi module, and
provides Haswell-specific functionality to make it work.

v2: simplify the commit as per Daniel Vetter suggestion.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DDI is introduced starting with Haswell GPU generation. So to simplify its
management in the future, we also add intel_ddi.c to hold all the
DDI-related items.

Buffer translations for DDI links must be initialized prior to enablement.
For FDI and DP, first 9 pairs of values are used to select the connection
parameters. HDMI uses the last pair of values and ignores the first 9
pairs. So we program HDMI values in both cases, which allows HDMI to work
over both FDI and DP-friendly buffers.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Every time we use the device after a period of idleness, check that the
power management setup is still sane. This is to workaround a bug
whereby it seems that we begin suppressing power management interrupts,
preventing SandyBridge+ from going into turbo mode.

This patch does have a side-effect. It removes the mark-busy for just
moving the cursor - we don't want to increase the render clock just for
the sprite, though we may want to bump the display frequency. I'd argue
that we do not, and certainly don't want to take the struct_mutex here
due to the large latencies that introduces.

References: https://bugs.freedesktop.org/show_bug.cgi?id=44006Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They require an AVI InfoFrame with a proper Pixel Repetition field.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To keep the consistency with the other fields.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They're now in intel_pm.c, so group them a bit better.
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We now have a nice home for power management code, so let's use it!

v2: Resolve conflict agains "Only enable IPS polling for gen5"
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

PCH PLLs aren't required for outputs on the CPU, so we shouldn't just
treat them as part of the pipe.

So split the code out and manage PCH PLLs separately, allocating them
when needed or trying to re-use existing PCH PLL setups when the timings
match.

v2: add num_pch_pll field to dev_priv (Daniel)
    don't NULL the pch_pll pointer in disable or DPMS will fail (Jesse)
    put register offsets in pll struct (Chris)

v3: Decouple enable/disable of PLLs from get/put.
v4: Track temporary PLL disabling during modeset
v5: Tidy PLL initialisation by only checking for num_pch_pll == 0 (Eugeni)
v6: Avoid mishandling allocation failure by embedding the small array of
    PLLs into the device struct

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44309
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (up to v2)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3+)
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Tested-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds intel_pm routine for generic power-related infrastructure
initialization.

v2: now that all the platform-specific stuff is initialized in one place, we
can also add back the static definitions to platform-specific functions which
we abstract now.
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NBen Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This moves the clock gating-related functions into intel_pm module.

Also, please note that we do change the function type from static to
non-static in this patch for the move, to prevent breaking bisecting with
non-working intermediate commit. Those are returned back to static form in
the following patch which setups a generic PM initialization function,
which was split into a different one to simplify review.

v2: rebase on top of latest drm-intel-next-queued to incorporate all the
changes that went there meanwhile.
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NBen Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This moves DRPS, RPS and RC6-related functionality into intel_pm module.

It also removes the linux/cpufreq.h include from intel_display, as its
only user was the GPU turbo-related functionality in Gen6+ code path.

v2: rebase on top of latest drm-intel-next-queued adding the bits that
shifted around since the last patch.
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NBen Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move watermarks and helper functions (such as cxsr and fifo buffers) into
intel_pm module.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This commit moves Frame Buffer Compression-related operations and support
functions into the new intel_pm module.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>