Since commit 39cee200 ("usb: musb: core: call init and shutdown for
the usb phy") the musb USB phy is initialised by musb_core, but the
original initialisation in the dsps-glue init callback was left in
place resulting in two calls to phy init during probe (and similarly,
two shutdowns on remove).

Drop the duplicate phy init and shutdown calls from the dsps glue in
favour of the ones in musb core, which other glue drivers rely on.

Note however that any generic phy is still initialised in the glue init
callback (just as for the other drivers).

Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Set the new HCD flag which prevents USB core from trying to manage our
phys.

This is needed to be able to associate the controller platform device
with the glue device device-tree node on the BBB which uses legacy USB
phys. Otherwise, the generic phy lookup in usb_phy_roothub_init() and
thus HCD registration fails repeatedly with -EPROBE_DEFER (see commit
178a0bce ("usb: core: hcd: integrate the PHY wrapper into the HCD
core")).

Note that a related phy-lookup issue was recently worked around in the
phy core by commit b7563e27 ("phy: work around 'phys' references to
usb-nop-xceiv devices"). Something similar may now be needed for other
USB phys, and in particular if we eventually want to let USB core manage
musb generic phys.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This clarifies the license of the code. While here also add an include
guard to the header file.

Fixes: 07dbff0d ("usb: core: add a wrapper for the USB PHYs on the HCD")
Suggested-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_unregister_driver may be called more than 1 time in some
hotplug cases,it will cause the kernel oops. This patch checked
dbc_tty_driver to make sure it is unregistered only 1 time.

[  175.741404] BUG: unable to handle kernel NULL pointer dereference at 0000000000000034
[  175.742309] IP: tty_unregister_driver+0x9/0x70
[  175.743148] PGD 0 P4D 0
[  175.743981] Oops: 0000 [#1] SMP PTI
[  175.753904] RIP: 0010:tty_unregister_driver+0x9/0x70
[  175.754817] RSP: 0018:ffffa8ff831d3bb0 EFLAGS: 00010246
[  175.755753] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[  175.756685] RDX: ffff92089c616000 RSI: ffffe64fe1b26080 RDI: 0000000000000000
[  175.757608] RBP: ffff92086c988230 R08: 000000006c982701 R09: 00000001801e0016
[  175.758533] R10: ffffa8ff831d3b48 R11: ffff92086c982100 R12: ffff92086c98827c
[  175.759462] R13: ffff92086c988398 R14: 0000000000000060 R15: ffff92089c5e9b40
[  175.760401] FS:  0000000000000000(0000) GS:ffff9208a0100000(0000) knlGS:0000000000000000
[  175.761334] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  175.762270] CR2: 0000000000000034 CR3: 000000011800a003 CR4: 00000000003606e0
[  175.763225] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  175.764164] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  175.765091] Call Trace:
[  175.766014]  xhci_dbc_tty_unregister_driver+0x11/0x30
[  175.766960]  xhci_dbc_exit+0x2a/0x40
[  175.767889]  xhci_stop+0x57/0x1c0
[  175.768824]  usb_remove_hcd+0x100/0x250
[  175.769708]  usb_hcd_pci_remove+0x68/0x130
[  175.770574]  pci_device_remove+0x3b/0xc0
[  175.771435]  device_release_driver_internal+0x157/0x230
[  175.772343]  pci_stop_bus_device+0x74/0xa0
[  175.773205]  pci_stop_bus_device+0x2b/0xa0
[  175.774061]  pci_stop_bus_device+0x2b/0xa0
[  175.774907]  pci_stop_bus_device+0x2b/0xa0
[  175.775741]  pci_stop_bus_device+0x2b/0xa0
[  175.776618]  pci_stop_bus_device+0x2b/0xa0
[  175.777452]  pci_stop_bus_device+0x2b/0xa0
[  175.778273]  pci_stop_bus_device+0x2b/0xa0
[  175.779092]  pci_stop_bus_device+0x2b/0xa0
[  175.779908]  pci_stop_bus_device+0x2b/0xa0
[  175.780750]  pci_stop_bus_device+0x2b/0xa0
[  175.781543]  pci_stop_and_remove_bus_device+0xe/0x20
[  175.782338]  pciehp_unconfigure_device+0xb8/0x160
[  175.783128]  pciehp_disable_slot+0x4f/0xd0
[  175.783920]  pciehp_power_thread+0x82/0xa0
[  175.784766]  process_one_work+0x147/0x3c0
[  175.785564]  worker_thread+0x4a/0x440
[  175.786376]  kthread+0xf8/0x130
[  175.787174]  ? rescuer_thread+0x360/0x360
[  175.787964]  ? kthread_associate_blkcg+0x90/0x90
[  175.788798]  ret_from_fork+0x35/0x40

Cc: <stable@vger.kernel.org> # 4.16
Fixes: dfba2174 ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: NZhengjun Xing <zhengjun.xing@linux.intel.com>
Tested-by: NChristian Kellner <christian@kellner.me>
Reviewed-by: NChristian Kellner <christian@kellner.me>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The new axp288 extcon driver has no dependency on USB itself but
calls the usb role switch helper functions. This causes a link error
when USB_COMMON is disabled, as that subdirectory never gets entered:

drivers/extcon/extcon-axp288.o: In function `axp288_usb_role_work':
extcon-axp288.c:(.text+0x47b): undefined reference to `usb_role_switch_set_role'
extcon-axp288.c:(.text+0x498): undefined reference to `usb_role_switch_get_role'
drivers/extcon/extcon-axp288.o: In function `axp288_extcon_probe':
extcon-axp288.c:(.text+0x675): undefined reference to `usb_role_switch_get'
extcon-axp288.c:(.text+0x6d1): undefined reference to `usb_role_switch_put'
drivers/extcon/extcon-axp288.o: In function `axp288_put_role_sw':
extcon-axp288.c:(.text+0x1c): undefined reference to `usb_role_switch_put'

There are multiple ways of fixing this, I chose to 'select USB_COMMON',
since that is how we solved the same problem for other helpers like
USB_LED_TRIG or PHY drivers.

Fixes: d54f063c ("extcon: axp288: Set USB role where necessary")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently hcd.c is the only consumer of the usb_phy_roothub logic. This
already includes the required header files so struct device is known.
However, future consumers might not know about struct device.
Add a forward declaration for struct device to fix potential future
consumers which don't include any of the struct device API headers.

Fixes: 07dbff0d ("usb: core: add a wrapper for the USB PHYs on the HCD")
Suggested-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the generic PHY support is disabled the stub of devm_of_phy_get_by_index
returns ENOSYS. This corner case isn't handled properly by
usb_phy_roothub_add_phy and at least breaks USB support on Raspberry Pi
(bcm2835_defconfig):

    dwc2 20980000.usb: dwc2_hcd_init() FAILED, returning -38
    dwc2: probe of 20980000.usb failed with error -38

Let usb_phy_roothub_alloc() return in case CONFIG_GENERIC_PHY is
disabled to fix this issue (compilers might even be smart enough to
optimize away most of the code within usb_phy_roothub_alloc and
usb_phy_roothub_add_phy if CONFIG_GENERIC_PHY is disabled). All
existing usb_phy_roothub_* functions are already NULL-safe, so no
special handling is required there.

Fixes: 07dbff0d ("usb: core: add a wrapper for the USB PHYs on the HCD")
Reported-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the USB controller can wake up the system (which is the case for
example with the Mediatek USB3 IP) then we must not call phy_exit during
suspend to ensure that the USB controller doesn't have to re-enumerate
the devices during resume.
However, if the USB controller cannot wake up the system (which is the
case for example on various TI platforms using a dwc3 controller) then
we must call phy_exit during suspend. Otherwise the PHY driver keeps the
clocks enabled, which prevents the system from reaching the lowest power
levels in the suspend state.

Solve this by introducing two new functions in the PHY wrapper which are
dedicated to the suspend and resume handling.
If the controller can wake up the system the new usb_phy_roothub_suspend
function will simply call usb_phy_roothub_power_off. However, if wake up
is not supported by the controller it will also call
usb_phy_roothub_exit.
The also new usb_phy_roothub_resume function takes care of calling
usb_phy_roothub_init (if the controller can't wake up the system) in
addition to usb_phy_roothub_power_on.

Fixes: 07dbff0d ("usb: core: add a wrapper for the USB PHYs on the HCD")
Fixes: 178a0bce ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Reported-by: NRoger Quadros <rogerq@ti.com>
Suggested-by: NRoger Quadros <rogerq@ti.com>
Suggested-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NRoger Quadros <rogerq@ti.com>
Tested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Before this patch usb_phy_roothub_init served two purposes (from a
caller's point of view - like hcd.c):
- parsing the PHYs and allocating the list entries
- calling phy_init on each list entry

While this worked so far it has one disadvantage: if we need to call
phy_init for each PHY instance then the existing code cannot be re-used.
Solve this by splitting off usb_phy_roothub_alloc which only parses the
PHYs and allocates the list entries.
usb_phy_roothub_init then gets a struct usb_phy_roothub and only calls
phy_init on each PHY instance (along with the corresponding cleanup if
that failed somewhere).

This is a preparation step for adding proper suspend support for some
hardware that requires phy_exit to be called during suspend and phy_init
to be called during resume.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: NRoger Quadros <rogerq@ti.com>
Tested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_phy_roothub_exit() should return the error code from the phy_exit()
call if exiting the PHY failed.
However, since a wrong variable is used usb_phy_roothub_exit() currently
always returns 0, even if one of the phy_exit calls returned an error.
Clang also reports this bug:
kernel/drivers/usb/core/phy.c:114:8: warning: explicitly assigning value of
variable of type 'int' to itself [-Wself-assign] error, forbidden
warning: phy.c:114

Fix this by assigning the error code from phy_exit() to the "ret"
variable to propagate the error correctly.

Fixes: 07dbff0d ("usb: core: add a wrapper for the USB PHYs on the HCD")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NRishabh Bhatnagar <rishabhb@codeaurora.org>
Tested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On some boards, under heavy load, the EC firmware is
unable to complete commands even in one second. Increasing
the command completion timeout value to five seconds.
Reported-by: NQuanxian Wang <quanxian.wang@intel.com>
Fixes: c1b0bc2d ("usb: typec: Add support for UCSI interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b07c1251

It is incomplete and causes hangs on devices when shutting down.  It
needs a much more "complete" fix in order to work properly.  As that fix
has not been merged, revert this patch for now before it causes any more
problems.

Cc: Greg Hackmann <ghackmann@google.com>
Cc: Adam Wallis <awallis@codeaurora.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DELAY_INIT quirk to fix the following problem with HP
v222w 16GB Mini:

usb 1-3: unable to read config index 0 descriptor/start: -110
usb 1-3: can't read configurations, error -110
usb 1-3: can't set config #1, error -110
Signed-off-by: NKamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: NKuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is the following build error with CONFIG_TYPEC_UCSI=m, CONFIG_FTRACE=y
and CONFIG_TRACING=n:

ERROR: "__tracepoint_ucsi_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_register_port" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_notify" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_reset_ppm" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_run_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_ack" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_connector_change" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!

This compination is quite hard to create because CONFIG_TRACING gets selected
only in rare cases without CONFIG_FTRACE.

The build failure is caused by conditionally compiling trace.c depending on
the wrong option CONFIG_FTRACE. Change this to depend on CONFIG_TRACING like
other users of tracepoints do.

Fixes: c1b0bc2d ("usb: typec: Add support for UCSI interface")
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix it to not print kernel pointer address. Remove the conditional
and debug message as it isn't very useful.
Signed-off-by: NShuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip_host calls device_attach() without holding dev->parent lock.
Fix it.
Signed-off-by: NShuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

vhci_hcd fails to do reset to put usb device and sockfd in the
module remove/stop paths. Fix the leak.
Signed-off-by: NShuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Validate !rhport < 0 before using it to access port_status array.
Signed-off-by: NShuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.

Resume condition is reported differently on USB 2.0 and USB 3.0 devices.

On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.

On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: NRavi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.

The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.

The binding documentation is updating accordingly.
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device

AMD suggests that a delay before xHC suspends can fix the issue.

I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.

Cc: stable@vger.kernel.org
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.

This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: NVasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Added the USB VID and PID for the USB serial console on some National
Instruments devices.
Signed-off-by: NKyle Roeschley <kyle.roeschley@ni.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add simple driver for libtransistor USB console.
This device is implemented in software:
https://github.com/reswitched/libtransistor/blob/development/lib/usb_serial.cSigned-off-by: NCollin May <collin@collinswebsite.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This reverts commit 79a0b331.

Turns out this is not an FTDI device after all.

Fixes: 79a0b331 ("USB: serial: ftdi_sio: add Id for Physik Instrumente E-870")
Reported-by: NMartin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

musb->endpoints[] has array size MUSB_C_NUM_EPS.
We must check array bounds before accessing the array and not afterwards.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NBin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Traditionally, PORTSC should be set before initializing ULPI phys. But
setting PORTSC before powering on the phy results in a kernel freeze
on imx53 based GE PPD. As a workaround this initializes the phy early
in the imx platform code and disables phy power management from the
core.
Signed-off-by: NFabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some trivial cleanups, that do not change functionality.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The register write can be done outside the if and else condition
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

evdo bit can be set or reset. We can not trust evdo bit
status after bootloader stage
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB_PHY_CTRL_FUNC is used specific for OTG port as described
in user manual. EVDO need to be set only for index 0 that
correspond to OTG port
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for the Physik Instrumente E-870 PIShift Drive
Electronics, a Piezo motor driver.
Signed-off-by: NMartin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The website is no longer used for tracking bugs.
Signed-off-by: NAaron Wu <aaron.wu@analog.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The blackfin architecture is getting removed, and this is the last
remaining architecture specific setting, so the various hacks
can be removed now.

From all I can tell, there are no remaining in-tree users of the
driver, but it could be used by out-of-tree platform ports.
I've marked the driver as 'depends on COMPILE_TEST', short of
removing it outright.

It was originally written for some ARM PXA machines using the same
chip, but that platform never really worked and the code has been
removed a long time ago.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAaron Wu <aaron.wu@analog.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The blackfin architecture is getting removed, so we can clean up
all the special cases in the musb driver.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAaron Wu <aaron.wu@analog.com>
Acked-by: NBin Liu <b-liu@ti.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
[arnd: adding in fixups from Aaron and Stephen]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The tile architecture is getting removed, so the ehci and ohci platform
glue drivers are no longer needed. In case of ohci, this is the last
one to define a PLATFORM_DRIVER macro, so we can remove even more.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: NKalle Valo <kvalo@codeaurora.org>
Acked-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:

spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
	free_ep_req(hidg->in_ep, hidg->req);
	goto try_again;
}

[...]

status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
	[...]
	=> usb_gadget_giveback_request
		=>
		f_hidg_req_complete
			=>
			spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire

Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.

It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
Reported-by: NTuba Yavuz <tuba@ece.ufl.edu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Mention that ->complete() should never be called from within
usb_ep_queue().
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>