Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

flush_dcache_range is not portable across architectures. Use
dma_sync_single instead. Also, the memory must be synchronised in the
receive path aswell.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the datasheet the ICSR register is at offset 27, not 22.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some architecture specific functions which are all
empty. Remove them.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The #else branches throughout this driver belong to a PowerPC 8xx for
which this driver is not used.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes following sparse warnings:

  CHECK   gianfar_ethtool.c
gianfar_ethtool.c:610:26: warning: symbol 'gfar_ethtool_ops' was not declared. Should it be static?
  CHECK   gianfar_mii.c
gianfar_mii.c:108:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:119:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:128:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:272:5: warning: cast removes address space of expression
gianfar_mii.c:271:15: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:340:11: warning: cast adds address space to expression (<asn:2>)
  CHECK   gianfar_sysfs.c
gianfar_sysfs.c:84:1: warning: symbol 'dev_attr_bd_stash' was not declared. Should it be static?
gianfar_sysfs.c:133:1: warning: symbol 'dev_attr_rx_stash_size' was not declared. Should it be static?
gianfar_sysfs.c:175:1: warning: symbol 'dev_attr_rx_stash_index' was not declared. Should it be static?
gianfar_sysfs.c:213:1: warning: symbol 'dev_attr_fifo_threshold' was not declared. Should it be static?
gianfar_sysfs.c:250:1: warning: symbol 'dev_attr_fifo_starve' was not declared. Should it be static?
gianfar_sysfs.c:287:1: warning: symbol 'dev_attr_fifo_starve_off' was not declared. Should it be static?
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In most cases (e.g. PCI drivers) MDIO and MAC controllers are
represented by the same device. But for SOC ethernets we have
separate devices. So, in SOC case, checking whether MDIO
controller may wakeup is not only makes little sense, but also
prevents us from doing per-netdevice wakeup management.

This patch reworks suspend/resume code so that now it checks
for net device's wakeup flags, not MDIO controller's ones.

Each netdevice should manage its wakeup flags, and phylib will
decide whether suspend an attached PHY or not.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements wakeup management for the gianfar driver.

The driver should set wakeup enable if WOL is enabled, so that
phylib won't power off an attached PHY.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Base versions handle constant folding now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Base versions handle constant folding now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent fix of data corruption when splicing from sockets uses
memory very inefficiently allocating a new page to copy each chunk of
linear part of skb. This patch uses the same page until it's full
(almost) by caching the page in sk_sndmsg_page field.

With changes from David S. Miller <davem@davemloft.net>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some platforms (for example pcm037) do not have an EEPROM fitted,
instead storing their mac address somewhere else.  The bootloader
fetches this and configures the ethernet adapter before the kernel is
started.

This patch allows a platform to indicate to the driver via the
SMSC911X_SAVE_MAC_ADDRESS flag that the mac address has already been
configured via such a mechanism, and should be saved before resetting
the chip.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On LAN9115/LAN9117/LAN9215/LAN9217, external phys are supported.  These
are usually indicated by a hardware strap which sets an "external PHY
detected" bit in the HW_CFG register.

In some cases it is desirable to override this hardware strap and force
use of either the internal phy or an external PHY.  This patch adds
SMSC911X_FORCE_INTERNAL_PHY and SMSC911X_FORCE_EXTERNAL_PHY flags so a
platform can indicate this preference via its platform_data.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The isr supports shared operation, so register it with the IRQF_SHARED
flag to indicate this.

This patch also removes the IRQF_DISABLED flag.  This driver doesn't
need it, and IRQF_DISABLED isn't guaranteed when using shared interrupts.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch adds support for the platform_device's resources to indicate
additional flags to use when registering the irq, for example
IORESOURCE_IRQ_LOWLEVEL (which corresponds to IRQF_TRIGGER_LOW).  These
should be set in the irq resource flags field.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/e1000/e1000_main.c

As the mmap handler gets called under mmap_sem, and we may grab
mmap_sem elsewhere under the socket lock to access user data, we
should avoid grabbing the socket lock in the mmap handler.

Since the only thing we care about in the mmap handler is for
pg_vec* to be invariant, i.e., to exclude packet_set_ring, we
can achieve this by simply using a new mutex.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Tested-by: NMartin MOKREJŠ <mmokrejs@ribosome.natur.cuni.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset.  This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.

Remove claimed support for 100M HD mode since it is not supported by
current firmware.

Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.

Always set the AN selector bits to 1 (802.3).

Fix confusion between Next Page and Extended Next Page.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This workaround is not specific to rev A.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on the loopback mode, there may be no pertinent link state
bits.  In this case we test the PHYXS RX fault bit instead.  Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In particular, set pause advertising bits properly.

A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before.  This ensures that the value is
correct after an online reset.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.

Update comments to explain exactly what we're doing.

Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750).  We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors.  This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware.  Therefore remove it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network.  It used
to work in 2.4 kernels.  Fix that.  Tested on a 21142 Rev 0x11.
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix inverted logic
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 0f0ca340 ("phy: power
management support") caused a regression in the gianfar driver.

Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.

This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.

A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc9420 performs an interrupt signalling test when the interface is
brought up.  The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.

This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit b31a1d8b ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx".  For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Toralf Förster and Randy Dunlap.

- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html

- http://lkml.org/lkml/2009/1/29/279

The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.

These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For kernel bugzilla #12537:
http://bugzilla.kernel.org/show_bug.cgi?id=12537

Free memory.
Signed-off-by: NDaniel Marjamäki <danielm77@spray.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>