The locking in mesh_{mpath,mpp}_table_grow not only
has an rcu_read_unlock() missing, it's also racy
(though really only technically since it's invoked
from a single function only) since it obtains the
new size of the table without any locking, so two
invocations of the function could attempt the same
resize.

Additionally, it uses synchronize_rcu() which is
rather expensive and can be avoided trivially here.

Modify the functions to only use the table lock
and use call_rcu() instead of synchronize_rcu().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 uses call_rcu() with functions that are
defined in the module, so it must use rcu_barrier()
at module exit time.

Luckily, this seems to not be a problem in practice
as module unload and unregistration takes a long
time and probably does multiple synchronize_rcu().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NGottfried Haider <gottfried.haider@gmail.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As long as no delay is required b/w channel change, scan work
is proceeding without scheduling a new work. In such case, we
can not abort scan work when the card was unplugged. This patch
completes the scanning immediately whenever the device goes down.
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers shouldn't attempt to advertise support
for more than one IBSS interface since mac80211
doesn't support that. Check and return an error
from ieee80211_register_hw() in that case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to provide multiple interfaces for a single device,
the driver will be required to advertise all possible
interface configurations to the stack.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We free name "dev" for something generic (like dev abstraction layer).
Additionaly code is cleaner now, especially magic dev->dev-dev chains.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mesh paths are deleted via mesh_path_del() which properly
deactivates the timer associated to a mesh path.  But if paths were
deleted by mesh_table_free(..., true) timers would not be deactivated.
This fixes this case.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* use proc_mkdir_mode() instead of create_proc_entry(S_IFDIR|...),
  export proc_mkdir_mode() for that, oh well.
* don't supply S_IFREG to proc_create_data(), it's unnecessary
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: <stable@kernel.org>
Reported-by: NMark Davis <marked86@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

mwifiex was using its own implementation of converting 802.11n
AMSDU to 802.3s.  This patch removes mwifiex specific
implementation and uses existing ieee80211_amsdu_to_8023s
routine.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the devices that have already stripped IEEE 802.11
header from the AMSDU SKB can not use ieee80211_amsdu_to_8023s
routine. This patch enhances ieee80211_amsdu_to_8023s() API by
changing mandatory removing of IEEE 802.11 header from AMSDU
to optional.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These definitions need to be exposed now that we can set the peer link
states via NL80211_ATTR_STA_PLINK_STATE.  They were already being
(opaquely) reported by NL80211_STA_INFO_PLINK_STATE.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

we are not doing anything by tracking the number of pending frames.
bail out when we first find a pending frame in any one of the 10 queues.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

some times the rssi control descriptor for the main antenna may be
negative like that of alternate antenna, hence before  incrementing
packet counts/rssi of main/alternate antenna make sure both main_rssi
and alt_rssi are positive only. this avoids wrong selection of antenna
due to diversity

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

configure fast diversity bias based on the antenna diversity group and
based on main/alt LNA configurations. also configure main antenna and
alternate antenna to gain-table 0 for diversity group 2(AR9485)

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

for the diversity group 2(AR9485) we swap the LNA's of main/ALT antenna
based on alternate antenna's rssi average in comparision with main
antenna's rssi, while for AR9285(antenna diversity group 0)we still
follow the older method of looking at the packet count in alternate
antenna

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9285 belongs to diversity group 0 and AR9485 belongs to diversity
group 2. Based on the diversity group we configure certain antenna
diversity paramaters such as lna1_lna2_delta and fast diversity
bias values. For AR9485 we have some gain table parameter which
selects the gain table 0/1 for main and alternate antenna

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

these are the two important modules that will be called by the antenna
diversity algorithm module in the rx. this will continuosly configure
the hardware based on the current diversity status obtained
from the algorithm

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* enable LNA-diversity, fast-diversity for AR9485 based  on
  the value read from EEPROM content
* if antenna diversity/combining is supported, set LNA1 for the main
  antenna and LNA2 for the alternate antenna based on the new diversity
  algorithm

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Cc: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

define few registers and macros to configure/enable Antenna diversity
parameters in AR9485

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

read antenna diversity and combining information from the EEPROM.
Enable antenna diversity/combining feature only when both LNA
diversity and fast diversity are supported

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Tested-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

this is necessary to support Antenna diversity and combining in new chip
sets such as AR9485, previously Antenna diversity support is available
only in AR9285

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The list_for_each_entry loop can fail, in which case the list element is
not removed from the list rfkill_fds.  Since this list is not accessed by
the loop, the addition of &data->list into the list is just moved after the
loop.

The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E,E1,E2;
identifier l;
@@

*list_add(&E->l,E1);
... when != E1
    when != list_del(&E->l)
    when != list_del_init(&E->l)
    when != E = E2
*kfree(E);// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.

Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During my quest to make mac80211 not have any RCU
warnings from sparse, I came across the a-MPDU code
again and it wasn't quite clear why it isn't racy.
So instead of assigning the tid_tx array with just
the spinlock held in ieee80211_start_tx_ba_session
use a separate temporary array protected only by
the spinlock and protect all assignments to the
"live" array by both the spinlock and the mutex so
that other code is easily verified to be correct.

Due to pointer assignment atomicity I don't think
this is a real issue, but I'm not sure, especially
on Alpha the current code might be problematic.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the ability to advertise interface combinations in nl80211.
This allows the driver to indicate what the combinations are
that it supports. "Combinations" of just a single interface are
implicit, as previously. Note that cfg80211 will enforce that
the restrictions are met, but not for all drivers yet (once all
drivers are updated, we can remove the flag and enforce for all).

When no combinations are actually supported, an empty list will
be exported so that userspace can know if the kernel exported
this info or not (although it isn't clear to me what tools using
the info should do if the kernel didn't export it).

Since some interface types are purely virtual/software and don't
fit the restrictions, those are exposed in a new list of pure SW
types, not subject to restrictions. This mainly exists to handle
AP-VLAN and monitor interfaces in mac80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:

In file included from arch/x86/include/asm/uaccess.h:573,
                 from include/net/checksum.h:25,
                 from include/linux/skbuff.h:28,
                 from drivers/net/wireless/iwlwifi/iwl-agn-rs.c:28:
In function 'copy_from_user',
    inlined from 'rs_sta_dbgfs_scale_table_write' at
    drivers/net/wireless/iwlwifi/iwl-agn-rs.c:3099:
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct

presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:

In file included from arch/x86/include/asm/uaccess.h:573,
                 from include/net/checksum.h:25,
                 from include/linux/skbuff.h:28,
                 from drivers/net/wireless/iwlegacy/iwl-4965-rs.c:28:
In function 'copy_from_user',
    inlined from 'iwl4965_rs_sta_dbgfs_scale_table_write' at
    drivers/net/wireless/iwlegacy/iwl-4965-rs.c:2616:
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct

presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/ssb/main.c:1336: error: 'SSB_PCICORE_BCAST_ADDR' undeclared (first use in this function)
drivers/ssb/main.c:1337: error: 'SSB_PCICORE_BCAST_DATA' undeclared (first use in this function)
drivers/ssb/main.c:1349: error: 'struct ssb_pcicore' has no member named 'dev'
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

old_assoc not used, remove it
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When the PAN context is active, but unused, it
may still block scans that take more dwell time
than its beacon interval (which is odd). Work
around this problem by using a default beacon
interval of 200 so scans will fit between.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

gcc is warning that a few variables in rate
scaling are set but never otherwise used.
This pointed out a few simplifications.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Before send the RXON command with associated flag set, always do disassociate
first to make sure uCode is in the correct state.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

If fail to enqueue host command, clear the STATUS_hcmD_ACTIVE bit
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add support in testmode for setting fixed rate
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add the capability to dump eeprom through testmode request
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Adding testmode trace/debug capability
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>