vmlinux.lds expects the fixup code to be on a section named .fixup. The
.text.fixup section is not mentioned on vmlinux.lds, and is included on
the resulting vmlinux (just after .text) only because of ld heuristics on
placing orphan sections.

However, placing .text.fixup outside .text breaks the definition of
_etext, making it exclude the .text.fixup contents. That makes .text.fixup
be ignored by the kernel initialization code that needs to know about
section locations, such as the code setting page protection bits.
Signed-off-by: NEduardo Habkost <ehabkost@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

The acer_wmi driver does a DMI scan for quirks, and then sets flags into the
"interface" datastructure for some cases. However, the quirks happen real early
before "interface" is per se initialized from NULL.

The patch below 1) adds a NULL pointer check and 2) (re)runs the quirks at the
end, when "interface" has it's final value.

Reported-by: kerneloops.org
Acked-by: NCarlos Corbacho <carlos@strangeworlds.co.uk>
CC: stable@vger.kernel.org
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipv6: protocol for address routes
  icmp: icmp_sk() should not use smp_processor_id() in preemptible code
  pkt_sched: Fix qdisc list locking
  pkt_sched: Fix qdisc_watchdog() vs. dev_deactivate() race
  sctp: fix potential panics in the SCTP-AUTH API.

This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes a problem spotted with zebra, but not sure if it is
necessary a kernel problem.  With IPV6 when an address is added to an
interface, Zebra creates a duplicate RIB entry, one as a connected
route, and other as a kernel route.

When an address is added to an interface the RTN_NEWADDR message
causes Zebra to create a connected route. In IPV4 when an address is
added to an interface a RTN_NEWROUTE message is set to user space with
the protocol RTPROT_KERNEL. Zebra ignores these messages, because it
already has the connected route.

The problem is that route created in IPV6 has route protocol ==
RTPROT_BOOT.  Was this a design decision or a bug? This fixes it. Same
patch applies to both net-2.6 and stable.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass namespace into icmp_xmit_lock, obtain socket inside and return
it as a result for caller.

Thanks Alexey Dobryan for this report:

Steps to reproduce:

	CONFIG_PREEMPT=y
	CONFIG_DEBUG_PREEMPT=y
	tracepath <something>

BUG: using smp_processor_id() in preemptible [00000000] code: tracepath/3205
caller is icmp_sk+0x15/0x30
Pid: 3205, comm: tracepath Not tainted 2.6.27-rc4 #1

Call Trace:
 [<ffffffff8031af14>] debug_smp_processor_id+0xe4/0xf0
 [<ffffffff80409405>] icmp_sk+0x15/0x30
 [<ffffffff8040a17b>] icmp_send+0x4b/0x3f0
 [<ffffffff8025a415>] ? trace_hardirqs_on_caller+0xd5/0x160
 [<ffffffff8025a4ad>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff8023a475>] ? local_bh_enable_ip+0x95/0x110
 [<ffffffff804285b9>] ? _spin_unlock_bh+0x39/0x40
 [<ffffffff8025a26c>] ? mark_held_locks+0x4c/0x90
 [<ffffffff8025a4ad>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff8025a415>] ? trace_hardirqs_on_caller+0xd5/0x160
 [<ffffffff803e91b4>] ip_fragment+0x8d4/0x900
 [<ffffffff803e7030>] ? ip_finish_output2+0x0/0x290
 [<ffffffff803e91e0>] ? ip_finish_output+0x0/0x60
 [<ffffffff803e6650>] ? dst_output+0x0/0x10
 [<ffffffff803e922c>] ip_finish_output+0x4c/0x60
 [<ffffffff803e92e3>] ip_output+0xa3/0xf0
 [<ffffffff803e68d0>] ip_local_out+0x20/0x30
 [<ffffffff803e753f>] ip_push_pending_frames+0x27f/0x400
 [<ffffffff80406313>] udp_push_pending_frames+0x233/0x3d0
 [<ffffffff804067d1>] udp_sendmsg+0x321/0x6f0
 [<ffffffff8040d155>] inet_sendmsg+0x45/0x80
 [<ffffffff803b967f>] sock_sendmsg+0xdf/0x110
 [<ffffffff8024a100>] ? autoremove_wake_function+0x0/0x40
 [<ffffffff80257ce5>] ? validate_chain+0x415/0x1010
 [<ffffffff8027dc10>] ? __do_fault+0x140/0x450
 [<ffffffff802597d0>] ? __lock_acquire+0x260/0x590
 [<ffffffff803b9e55>] ? sockfd_lookup_light+0x45/0x80
 [<ffffffff803ba50a>] sys_sendto+0xea/0x120
 [<ffffffff80428e42>] ? _spin_unlock_irqrestore+0x42/0x80
 [<ffffffff803134bc>] ? __up_read+0x4c/0xb0
 [<ffffffff8024e0c6>] ? up_read+0x26/0x30
 [<ffffffff8020b8bb>] system_call_fastpath+0x16/0x1b

icmp6_sk() is similar.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: authenc - Avoid using clobbered request pointer

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix call of alc888_coef_init()
  ALSA: hda_intel: enable snoop for nvidia HDA controller

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: Update documentation to remind users to update mke2fs.conf
  ext4: Fix small file fragmentation
  ext4: Initialize writeback_index to 0 when allocating a new inode
  ext4: make sure ext4_has_free_blocks returns 0 for ENOSPC
  ext4: journal credit fix for the delayed allocation's writepages() function
  ext4: Rework the ext4_da_writepages() function
  ext4: journal credits reservation fixes for DIO, fallocate
  ext4: journal credits reservation fixes for extent file writepage
  ext4: journal credits calulation cleanup and fix for non-extent writepage
  ext4: Fix bug where we return ENOSPC even though we have plenty of inodes
  ext4: don't try to resize if there are no reserved gdt blocks left
  ext4: Use ext4_discard_reservations instead of mballoc-specific call
  ext4: Fix ext4_dx_readdir hash collision handling
  ext4: Fix delalloc release block reservation for truncate
  ext4: Fix potential truncate BUG due to i_prealloc_list being non-empty
  ext4: Handle unwritten extent properly with delayed allocation

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: enable LB_BIAS by default

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: fix synchronize_rcu() so that kernel-doc works

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  nohz: fix wrong event handler after online an offlined cpu

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: work around MTRR mask setting, v2
  x86: fix section mismatch warning - uv_cpu_init
  x86: fix VMI for early params
  x86: fix two modpost warnings in mm/init_64.c
  x86: fix 1:1 mapping init on 64-bit (memory hotplug case)
  x86: work around MTRR mask setting
  x86: PAT Update validate_pat_support for intel CPUs
  devmem, x86: PAT Change /dev/mem mmap with O_SYNC to use UC_MINUS
  x86: PAT proper tracking of set_memory_uc and friends
  x86: fix BUG: unable to handle kernel paging request (numaq_tsc_disable)
  x86: export pv_lock_ops non-GPL
  x86, mmiotrace: silence section mismatch warning - leave_uniprocessor
  x86: use WARN() in arch/x86/kernel
  x86: use WARN() in arch/x86/mm/ioremap.c
  werror: fix pci calgary
  x86: fix oprofile + hibernation badness
  x86, SGI UV: hardcode the TLB flush interrupt system vector
  x86: fix Xorg startup/shutdown slowdown with PAT
  x86: fix "kernel won't boot on a Cyrix MediaGXm (Geode)"
  x86 iommu: remove unneeded parenthesis

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] pata_it821x: fix warning
  libata: Fix a large collection of DMA mode mismatches
  ahci: sis controllers actually can do PMP
  pata_via: clean up recent tf_load changes
  libata: restore SControl on detach
  libata: use ata_link_printk() when printing SError
  libata: always do follow-up SRST if hardreset returned -EAGAIN
  libata: fix EH action overwriting in ata_eh_reset()
  sata_mv: add the Gen IIE flag to the SoC devices.
  ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
  ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
  sata_mv: don't issue two DMA commands concurrently
  libata: implement no[hs]rst force params

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Fix deadlock on RTNL in ipoib_stop()
  IB/ipath: Fix incorrect check for max physical address in TID
  IB/ipath: Fix lost UD send work request

Authenc works in two stages for encryption, it first encrypts and
then computes an ICV.  The context memory of the request is used
by both operations.  The problem is that when an asynchronous
encryption completes, we will compute the ICV and then reread the
context memory of the encryption to get the original request.

It just happens that we have a buffer of 16 bytes in front of the
request pointer, so ICVs of 16 bytes (such as SHA1) do not trigger
the bug.  However, any attempt to uses a larger ICV instantly kills
the machine when the first asynchronous encryption is completed.

This patch fixes this by saving the request pointer before we start
the ICV computation.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Using init_hook to call alc888_coef_init() is problematic for configurations
that already set another init_hook.  Better to put it in alc_init() as is
(although it looks a bit hackish).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

improve the debug printout:

- make it actually display something
- print it only once

would be nice to have a WARN_ONCE() facility, to feed such things to
kerneloops.org.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

WARNING: vmlinux.o(.cpuinit.text+0x3cc4): Section mismatch in reference from the function uv_cpu_init() to the function .init.text:uv_system_init()
The function __cpuinit uv_cpu_init() references
a function __init uv_system_init().
If uv_system_init is only used by uv_cpu_init then
annotate uv_system_init with a matching annotation.

uv_system_init was ment to be called only once, so do it from codepath
(native_smp_prepare_cpus) which is called once, right before activation
of other cpus (smp_init).

Note: old code relied on uv_node_to_blade being initialized to 0,
but it'a not initialized from anywhere.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: NJack Steiner <steiner@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Since some qdiscs call qdisc_tree_decrease_qlen() (so qdisc_lookup())
without rtnl_lock(), adding and deleting from a qdisc list needs
additional locking. This patch adds global spinlock qdisc_list_lock
and wrapper functions for modifying the list. It is considered as a
temporary solution until hfsc_dequeue(), netem_dequeue() and
tbf_dequeue() (or qdisc_tree_decrease_qlen()) are redone.

With feedback from Herbert Xu and David S. Miller.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function

Pretty horrid fix, but so's a warning..
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.

This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.

Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)

Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
 <dave.mueller@gmx.ch>  -jg]
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15.  However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first.  Interestingly, the SRST itself
succeeds but the following commands fail.

If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.

Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit bfce5e01 implemented custom
tf_load for pata_via.  This patch cleans it up a bit.

* Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE
  when necessary.

* Rename via_ata_tf_load() to via_tf_load().

* No need to set .tf_load in via_port_ops_noirq as it inherits from
  via_port_ops.

* Clean up indentation.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Save SControl during probing and restore it on detach.  This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).

It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill.  For now, do it only for detach.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

SError belongs to link not port.  Use ata_link_printk() to print it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN.  However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN.  This
makes reset paths more predictable and thus less error-prone.

While at it, move hardreset error checking such that it's done right
after hardreset is finished.  This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset().  The original intention was to clear reset action
which wasn't selected.  This can cause unexpected behavior when other
EH actions are scheduled together with reset.  Fix it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch
will fix various issues when working with PMP and/or NCQ.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Resend with proper whitespace.

This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sata_mv allowed issuing two DMA commands concurrently which the
hardware allows.  Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Implement force params nohrst, nosrst and norst.  This is to work
around reset related problems and ease debugging.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

while fixing a different bug i moved the call to vmi_init before
early params could be parsed.

This broke the vmi specific commandline parameters.
Fix that, by moving vmi initialization after kernel has got a chance to
parse early parameters.
Signed-off-by: NAlok N Kataria <akataria@vmware.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

early_io{re,un}map() are __init and hence can't be called from __meminit
functions.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

While I don't have a hotplug capable system at hand, I think two issues need
fixing:

- pud_phys (in kernel_physical_ampping_init()) would remain uninitialized in
  the after_bootmem case

- the locking done just around phys_pmd_{init,update}() would leave out pgd
  updates, and it was needlessly covering code portions that do allocations
  (perhaps using a more friendly gfp value in alloc_low_page() would then be
  possible)
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Joshua Hoblitt reported that only 3 GB of his 16 GB of RAM is
usable. Booting with mtrr_show showed us the BIOS-initialized
MTRR settings - which are all wrong.

So the root cause is that the BIOS has not set the mask correctly:

>               [    0.429971]  MSR00000200: 00000000d0000000
>               [    0.433305]  MSR00000201: 0000000ff0000800
> should be ==> [    0.433305]  MSR00000201: 0000003ff0000800
>
>               [    0.436638]  MSR00000202: 00000000e0000000
>               [    0.439971]  MSR00000203: 0000000fe0000800
> should be ==> [    0.439971]  MSR00000203: 0000003fe0000800
>
>               [    0.443304]  MSR00000204: 0000000000000006
>               [    0.446637]  MSR00000205: 0000000c00000800
> should be ==> [    0.446637]  MSR00000205: 0000003c00000800
>
>               [    0.449970]  MSR00000206: 0000000400000006
>               [    0.453303]  MSR00000207: 0000000fe0000800
> should be ==> [    0.453303]  MSR00000207: 0000003fe0000800
>
>               [    0.456636]  MSR00000208: 0000000420000006
>               [    0.459970]  MSR00000209: 0000000ff0000800
> should be ==> [    0.459970]  MSR00000209: 0000003ff0000800

So detect this borkage and add the prefix 111.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5212/1: pxa: fix build error when CPU_PXA310 is not defined
  [ARM] 5208/1: fsg-setup.c fixes
  [ARM] fix impd1.c build warning
  [ARM] e400 config use MFP
  [ARM] e740 config use MFP
  [ARM] Fix eseries IRQ limit
  [ARM] clocklib: Update users of aliases to new API
  [ARM] clocklib: Allow dynamic alias creation
  [ARM] eseries: whitespace fixes and cleanup

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  pnp: fix "add acpi:* modalias entries"
  UIO: generic irq handling for some uio platform devices
  UIO: uio_pdrv: fix license specification
  UIO: uio_pdrv: fix memory leak
  block: drop references taken by class_find_device()
  block: fix partial read() of /proc/{partitions,diskstats}
  PM: Remove WARN_ON from device_pm_add
  driver core: add init_name to struct device
  PM: don't skip device PM init when CONFIG_PM_SLEEP isn't set and CONFIG_PM is set
  driver model: anti-oopsing medicine
  dev_printk(): constify the `dev' argument
  drivers/base/driver.c: remove unused to_dev() macro
  Documentation: HOWTO-ja_JP-sync patch
  Japanese translation of Documentation/SubmitChecklist
  kobject: Replace ALL occurrences of '/' with '!' instead of only the first one.

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
  USB: automatically enable RHSC interrupts
  USB: Don't rebind before "complete" callback
  USB: Add new PM callback methods for USB
  USB: Defer Set-Interface for suspended devices
  USB: Add udev argument to interface suspend/resume functions
  USB: cdc-acm: don't unlock acm->mutex on error path
  MUSB: Fix index register corruption seen with g_ether and Windows host
  usb: musb: get rid of MUSB_LOGLEVEL and use parameter
  usb: musb: get rid of procfs entry
  USB: Fix pxa27x_udc usb speed handling.
  USB: cdc-acm: quirk for Conexant CX93010 USB modem
  USB: fix bug in usb_unlink_anchored_urbs()
  usb-serial: option support HSDPA modem A2502
  USB: ISP1760: fixed trivial math in comment