Allow the user to configure the kernel to omit support for floating
point, by setting CONFIG_MIPS_FP_SUPPORT=n. In an attempt to avoid
problems for users who don't understand the impact of this, only expose
the option when CONFIG_EXPERT=y.

When CONFIG_MIPS_FP_SUPPORT=n all support for FPU hardware, FPU
emulation & FP context will be removed from the kernel. If a userland
program attempts to execute a floating point instruction it will receive
a SIGILL.

Setting CONFIG_MIPS_FP_SUPPORT=n shaves around 112KB from a
64r6el_defconfig build using GCC 8.1.0.

This also helps prepare us for supporting the nanoMIPS ISA, for which
floating point support has not been finalized.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21014/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point & so don't
need to preserve floating point context for tasks. Remove that context
from struct task_struct.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21013/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so
there's no point compiling in our FPU emulator. Avoid doing so,
providing stub versions of dsemul cleanup functions that are called from
signal & task handling code.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21012/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so we
don't need to worry about floating point exceptions pending in the
Floating point Control & Status Register (FCSR) during switch_to(). Stub
out the __sanitize_fcr31() macro in this case.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21010/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so we can
avoid needless checks of ELF headers specifying the FP ABI or NaN
encoding to use. Deselect CONFIG_ARCH_BINFMT_ELF_STATE in this case to
avoid the need for our arch_elf_pt_proc() & arch_check_elf() functions,
and stub out the mips_set_personality_nan() & mips_set_personality_fp()
functions such that SET_PERSONALITY() doesn't need to worry about any of
this.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21011/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so
there's no need to save & restore floating point context around signals.
This prepares us for the removal of FP context from struct task_struct
later.

Since MSA context is a superset of FP context support for it similarly
needs to be removed when MSA/FP support is disabled.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21009/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so remove
the related ptrace support. Besides removing code which should not be
needed, this prepares us for the removal of FPU state in struct
task_struct which this code requires.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21008/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so remove
support for floating point instructions from emulate_load_store_insn() &
emulate_load_store_microMIPS(). This code should not be needed & relies
upon access to FPU state in struct task_struct which will later be
removed.

Similarly & for the same reasons, when CONFIG_CPU_HAS_MSA=n remove
support for MSA instructions. Since MSA support depends upon FP support
this is implied when CONFIG_MIPS_FP_SUPPORT=n.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21020/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so remove
the floating point branch support from __compute_return_epc_for_insn() &
__mm_isBranchInstr(). This code should never be needed & more
importantly relies upon FPU state in struct task_struct which will later
be removed.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21017/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so we'll
never need to enable the FPU. Avoid doing so on a Co-Processor Unusable
exception (do_cpu), and remove the Floating Point Exception handler
(do_fpe) which should never be executed when the FPU is disabled.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21007/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point so there's
no point in attempting to detect an FPU. Avoid doing so.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21021/
Cc: linux-mips@linux-mips.org

Provide stub versions of functions in asm/fpu.h when
CONFIG_MIPS_FP_SUPPORT=n. Two approaches are taken to the functions
provided:

  - Functions which can safely be called when FP is not enabled provide
    stubs which return an error where appropriate or are simple no-ops.

  - Functions which should only ever be called in cases where
    cpu_has_fpu is true or the FPU was successfully enabled are declared
    extern & annotated with __compiletime_error() to detect cases in
    which they are called incorrectly.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21006/
Cc: linux-mips@linux-mips.org

When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so
there's no point in detecting presence of an FPU. Hardcode
cpu_has_fpu=0 such that we optimize out code that makes use of the FPU.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21005/
Cc: linux-mips@linux-mips.org

Introduce a Kconfig variable that will indicate whether to include
support for floating point in the kernel. For now this is always
enabled, and will be made configurable in a later patch.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21016/
Cc: linux-mips@linux-mips.org

Introduce a CONFIG_CPU_R2300_FPU Kconfig symbol mirroring the existing
CONFIG_CPU_R4K_FPU, and use it to determine whether to build r4k_fpu.S.

This removes the duplicate R3000 & TX39XX cases in
arch/mips/kernel/Makefile and prepares us for the possibility of
disabling FP support later.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21004/
Cc: linux-mips@linux-mips.org

asm/fpu.h contains forward declarations of struct sigcontext & struct
sigcontext32 which appear to have been unused since commit 137f6f3e
("MIPS: Cleanup signal code initialization"). Remove the dead code.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21015/
Cc: linux-mips@linux-mips.org

Emulated floating point instructions don't ensure that the PF_USED_MATH
flag is set for the task. This results in a couple of inconsistencies:

  - ptrace will return the default initial state of FP registers rather
    than the values actually stored in struct thread_struct, hiding
    state that has been updated by emulated floating point instructions.

  - If a task migrates to a CPU with an FPU after having emulated
    floating point instructions then its floating point register state
    will be reset to the default ~0 bit pattern, losing state from the
    emulated instructions.

Fix this by calling init_fp_ctx() from fpu_emulator_cop1Handler() to
consistently initialize FP state if it was previously uninitialized,
setting the PF_USED_MATH flag in the process.

All callers of fpu_emulator_cop1Handler() either call lose_fpu(1) before
it in order to save any live FPU registers to struct thread_struct, or
in the case of do_cpu() already know that the task does not own an FPU
so lose_fpu(1) would be a no-op. Since we know that saving FP context
will be unnecessary in the case where FP context was just initialized we
move this call into fpu_emulator_cop1Handler() too, providing
consistency & avoiding needless duplication.

Calls to own_fpu(1) are common after return from
fpu_emulator_cop1Handler() too, but this would not be a no-op in the
do_cpu() case so these are left as-is. A potential future improvement
could be to have fpu_emulator_cop1Handler() restore FPU state
automatically only if it saved it, though this may not be optimal if
some callers are better off without their current calls to own_fpu(1).
One potential example of this could be mipsr2_decoder() which as-is
could end up saving & restoring FP context repeatedly & unnecessarily if
emulating multiple FP instructions.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21003/
Cc: linux-mips@linux-mips.org

MIPS has up until now had 3 different ways for a task's floating point
context to be initialized:

  - If the task's first use of FP involves it gaining ownership of an
    FPU then _init_fpu() is used to initialize the FPU's registers such
    that they all contain ~0, and the FPU registers will be stored to
    struct thread_info later (eg. when context switching).

  - If the task first uses FP on a CPU without an associated FPU then
    fpu_emulator_init_fpu() initializes the task's floating point
    register state in struct thread_info such that all floating point
    register contain the bit pattern 0x7ff800007ff80000, different to
    the _init_fpu() behaviour.

  - If a task's floating point context is first accessed via ptrace then
    init_fp_ctx() initializes the floating point register state in
    struct thread_info to ~0, giving equivalent state to _init_fpu().

The _init_fpu() path has 2 separate implementations - one for r2k/r3k
style systems & one for r4k style systems. The _init_fpu() path also
requires that we be careful to clear & restore the value of the
Config5.FRE bit on modern systems in order to avoid inadvertently
triggering floating point exceptions.

None of this code is in a performance critical hot path - it runs only
the first time a task uses floating point. As such it doesn't seem to
warrant the complications of maintaining the _init_fpu() path.

Remove _init_fpu() & fpu_emulator_init_fpu(), instead using
init_fp_ctx() consistently to initialize floating point register state
in struct thread_info. Upon a task's first use of floating point this
will typically mean that we initialize state in memory & then load it
into FPU registers using _restore_fp() just as we would on a context
switch. For other paths such as __compute_return_epc_for_insn() or
mipsr2_decoder() this results in a significant simplification of the
work to be done.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21002/
Cc: linux-mips@linux-mips.org

The BMIPS5xxx core_init function contains a call to an init_fpu function
inside an #ifdef whose condition never evaluates true. Remove the dead
code. FPU initialization happens later, primarily when a userland
program attempts to use it.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21018/
Cc: linux-mips@linux-mips.org

From MIPSr6 onwards FP64 support is mandatory, and so
CONFIG_MIPS_O32_FP64_SUPPORT is always selected for configurations which
support O32 binaries. Hide the useless unchangeable prompt in these
cases.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21019/
Cc: linux-mips@linux-mips.org

If we built the kernel targeting the microMIPS ISA then the very fact
that the kernel is running implies that the CPU supports microMIPS. Thus
we can hardcode cpu_has_mmips to 1 allowing the compiler greater scope
for optimisation due to the compile-time constant.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21022/
Cc: linux-mips@linux-mips.org

The GCC_OFF_SMALL_ASM macro defines the constraint to use for
instructions needing "small offsets", typically the LL or SC
instructions. Historically these had 16 bit offsets, but microMIPS &
MIPS32/MIPS64r6 onwards reduced the width of the offset field.

GCC 4.9 & higher supports a ZC constraint which matches the offset
requirements of the LL & SC instructions. Where supported we can use
the ZC constraint regardless of ISA, and it will handle the requirements
of the ISA correctly. As such we require 3 cases:

  - GCC 4.9 & higher can use ZC.

  - GCC older than 4.9 must use the older R constraint, which does not
    take into account microMIPS or MIPSr6.

  - microMIPS builds therefore require GCC 4.9 or higher. MIPSr6 support
    was only introduced in newer compilers anyway so it can be ignored
    here.

The current code complicates this a little by specifically having MIPSr6
bypass the GCC version check, and using the R constraint for pre-MIPSr6
builds even if the compiler supports ZC which would be equivalent.

Simplify this such that the code straightforwardly implements the 3
cases outlined above.

For non-GCC compilers we presume that ZC is safe to use. In practice the
only non-GCC compiler of interest is clang and it has supported the ZC
constraint since version 3.7.0. It seems safe enough to presume that
nobody will expect to built a working kernel using a clang version older
than that, and if they do then they'll have bigger problems. As such we
don't check the clang version number & just presume ZC is usable when
the compiler is not GCC.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20999/
Cc: linux-mips@linux-mips.org

asm/compiler.h defined GCC_IMM_ASM & GCC_REG_ACCUM macros, both of which
are defined differently for GCC pre-3.4 or GCC 3.4 & higher. We only
support building with GCC 4.6 & higher since commit cafa0010 ("Raise
the minimum required gcc version to 4.6"), which makes the pre-3.4
definition dead code.

Rather than leave the macro definitions around, inline the GCC 3.4 &
higher definitions into the single file that uses them & remove the
macros entirely.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21000/
Cc: linux-mips@linux-mips.org

This supports computers based on the R4000SC processor:

* DECstation 5000/150 and DECsystem 5000/150,

* Personal DECstation 5000/50, Personal DECsystem 5000/50,

and computers based on the R4400SC processor:

* DECstation 5000/260 and DECsystem 5000/260,

* DECsystem 5900/260,

in the 64-bit mode.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20986/
Cc: Ralf Baechle <ralf@linux-mips.org>

This supports computers based on the R4000SC processor:

* DECstation 5000/150 and DECsystem 5000/150,

* Personal DECstation 5000/50, Personal DECsystem 5000/50,

and computers based on the R4400SC processor:

* DECstation 5000/260 and DECsystem 5000/260,

* DECsystem 5900/260,

in the 32-bit mode.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20985/
Cc: Ralf Baechle <ralf@linux-mips.org>

Regenerate the R3k DECstation defconfig, in particular including more
relevant drivers.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20984/
Cc: Ralf Baechle <ralf@linux-mips.org>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20991/
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

Allows the users of ptrace to access memory mapped by the ptraced process
using the same cache coherency attributes as the original process.
For example while using gdb with ioremap_prot() incorporated, both gdb and
the process being traced will have same cache coherency attributes.
Signed-off-by: NHassan Naveed <hnaveed@wavecomp.com>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20955/
Cc: <linux-mips@linux-mips.org>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20988/
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

Pull scheduler fixes from Ingo Molnar:
 "A memory (under-)allocation fix and a comment fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/topology: Fix off by one bug
  sched/rt: Update comment in pick_next_task_rt()

Pull x86 fixes from Ingo Molnar:
 "A number of fixes and some late updates:

   - make in_compat_syscall() behavior on x86-32 similar to other
     platforms, this touches a number of generic files but is not
     intended to impact non-x86 platforms.

   - objtool fixes

   - PAT preemption fix

   - paravirt fixes/cleanups

   - cpufeatures updates for new instructions

   - earlyprintk quirk

   - make microcode version in sysfs world-readable (it is already
     world-readable in procfs)

   - minor cleanups and fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  compat: Cleanup in_compat_syscall() callers
  x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
  objtool: Support GCC 9 cold subfunction naming scheme
  x86/numa_emulation: Fix uniform-split numa emulation
  x86/paravirt: Remove unused _paravirt_ident_32
  x86/mm/pat: Disable preemption around __flush_tlb_all()
  x86/paravirt: Remove GPL from pv_ops export
  x86/traps: Use format string with panic() call
  x86: Clean up 'sizeof x' => 'sizeof(x)'
  x86/cpufeatures: Enumerate MOVDIR64B instruction
  x86/cpufeatures: Enumerate MOVDIRI instruction
  x86/earlyprintk: Add a force option for pciserial device
  objtool: Support per-function rodata sections
  x86/microcode: Make revision and processor flags world-readable

Pull perf updates and fixes from Ingo Molnar:
 "These are almost all tooling updates: 'perf top', 'perf trace' and
  'perf script' fixes and updates, an UAPI header sync with the merge
  window versions, license marker updates, much improved Sparc support
  from David Miller, and a number of fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
  perf intel-pt/bts: Calculate cpumode for synthesized samples
  perf intel-pt: Insert callchain context into synthesized callchains
  perf tools: Don't clone maps from parent when synthesizing forks
  perf top: Start display thread earlier
  tools headers uapi: Update linux/if_link.h header copy
  tools headers uapi: Update linux/netlink.h header copy
  tools headers: Sync the various kvm.h header copies
  tools include uapi: Update linux/mmap.h copy
  perf trace beauty: Use the mmap flags table generated from headers
  perf beauty: Wire up the mmap flags table generator to the Makefile
  perf beauty: Add a generator for MAP_ mmap's flag constants
  tools include uapi: Update asound.h copy
  tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
  tools include uapi: Update linux/fs.h copy
  perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
  perf cs-etm: Correct CPU mode for samples
  perf unwind: Take pgoff into account when reporting elf to libdwfl
  perf top: Do not use overwrite mode by default
  perf top: Allow disabling the overwrite mode
  perf trace: Beautify mount's first pathname arg
  ...

Pull irq fixes from Ingo Molnar:
 "An irqchip driver fix and a memory (over-)allocation fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
  irq/matrix: Fix memory overallocation

With the addition of the NUMA identity level, we increased @level by
one and will run off the end of the array in the distance sort loop.

Fixed: 051f3ca0 ("sched/topology: Introduce NUMA identity node sched domain")
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Signed-off-by: NIngo Molnar <mingo@kernel.org>