Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.

Fixes: 47558acd ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory.  Do the same sequence in the error path
of probe to be safe and consistent.

Fixes: c20dc142 ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed.  Fix it
by propagating the error code to the caller.

Fixes: 1b9394e5 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an indexing bug in determining these ethtool priority
counters.  Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index.  This index is then used
to obtain the proper CoS queue counter.  Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.

Fixes: e37fed79 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to other drivers, properly clear the devlink port type when
removing the device before unregistration.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If firmware command returns error code as HWRM_ERR_CODE_BUSY, which
means it cannot handle the command due to a conflicting command
from another function, convert it to -EAGAIN.  If it is an ethtool
operation, this error code will be returned to userspace.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return code is not needed in some of these functions, as the return
code from firmware message is ignored. Remove the unused rc variable
and also convert functions to void.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of converting error code in firmware message to standard
code, checking for firmware return code is removed in most of the
places. Remove the assignment of return code where the function
can directly return.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver stores a copy of the DCB settings that have been applied to
the firmware.  After firmware reset, the firmware settings are gone and
will revert back to default.  Clear the driver's copy so that if there
is a DCBNL request to get the settings, the driver will retrieve the
current settings from the firmware.  lldpad keeps the DCB settings in
userspace and will re-apply the settings if it is running.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we are in continuous NAPI polling mode, the current code in
bnxt_poll_p5() will only process the completion rings and will not
process the NQ until interrupt is re-enabled.  Tis logic works and
will not cause RX or TX starvation, but async events in the NQ may
be delayed for the duration of continuous NAPI polling.  These
async events may be firmware or VF events.

Continue to handle the NQ after we are done polling the completion
rings.  This actually simplies the code in bnxt_poll_p5().

Acknowledge the NQ so these async events will not overflow.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the function by removing tha 'all' parameter.  In the current
code, the caller has to specify whether to update/arm both completion
rings with the 'all' parameter.

Instead of this, we can just update/arm all the completion rings
that have been polled.  By setting cpr->had_work_done earlier in
__bnxt_poll_work(), we know which completion ring has been polled
and can just update/arm all the completion rings with
cpr->had_work_done set.

This simplifies the function with one less parameter and works just
as well.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_poll_p5(), the logic polls for up to 2 completion rings (RX and
TX) for work.  In the current code, if we reach budget polling the
first completion ring, we will stop.  If the other completion ring
has work to do, we will handle it when NAPI calls us back.

This is not optimal.  We potentially leave an unproceesed entry in
the NQ.  When we are finally done with NAPI polling and re-enable
interrupt, the remaining entry in the NQ will cause interrupt to
be triggered immediately for no reason.

Modify the code in bnxt_poll_p5() to keep looping until all NQ
entries are handled even if the first completion ring has reached
budget.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().

Use of put_unaligned_le64 should be correct. pci_get_dsn() will perform
two pci_read_config_dword calls. The first dword will be placed in the
first 32 bits of the u64, while the second dword will be placed in the
upper 32 bits of the u64.

On Little Endian systems, the least significant byte comes first, which
will be the least significant byte of the first dword, followed by the
least significant byte of the second dword. Since the _le32 variations
do not perform byte swapping, we will correctly copy the dwords into the
dsn[] array in the same order as before.

On Big Endian systems, the most significant byte of the second dword
will come first. put_unaligned_le64 will perform a CPU_TO_LE64, which
will swap things correctly before copying. This should also end up with
the correct bytes in the dsn[] array.

While at it, fix a small typo in the netdev_info error message when the
DSN cannot be read.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use linux kernel version for ethtool and module versions.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MTU changes may affect the number of IRQs so we must call
bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter
set to true.  The reason is that a larger MTU may require
aggregation rings not needed with smaller MTU.  We may not be
able to allocate the required number of aggregation rings and
so we reduce the number of channels which will change the number
of IRQs.  Without this patch, it may crash eventually in
pci_disable_msix() when the IRQs are not properly unwound.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing newlines to netdev_* format strings so the lines
aren't buffered by the printk subsystem.
Nitpicked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If crashed kernel does not shutdown the NIC properly, PCIe FLR
is required in the kdump kernel in order to initialize all the
functions properly.

Fixes: d629522e ("bnxt_en: Reduce memory usage when running in kdump kernel.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Especially when bnxt_shutdown() is called during kexec, we need to
disable MSIX and disable Bus Master to completely quiesce the device.
Make these 2 calls unconditionally in the shutdown method.

Fixes: c20dc142 ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently only calls netdev_set_tc_queue when the number of
TCs is greater than 1.  Instead, the comparison should be greater than
or equal to 1.  Even with 1 TC, we need to set the queue mapping.

This bug can cause warnings when the number of TCs is changed back to 1.

Fixes: 7809592d ("bnxt_en: Enable MSIX early in bnxt_init_one().")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The current logic that calls pci_disable_device() in __bnxt_close_nic()
during firmware reset is flawed.  If firmware is still alive, we're
disabling the device too early, causing some firmware commands to
not reach the firmware.

Fix it by moving the logic to bnxt_reset_close().  If firmware is
in fatal condition, we call pci_disable_device() before we free
any of the rings to prevent DMA corruption of the freed rings.  If
firmware is still alive, we call pci_disable_device() after the
last firmware message has been sent.

Fixes: 3bc7d4a3 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

bnxt_ulp_start() needs to be called before SRIOV is re-enabled after
firmware reset.  Re-enabling SRIOV may consume all the resources and
may cause the RDMA driver to fail to get MSIX and other resources.
Fix it by calling bnxt_ulp_start() first before calling
bnxt_reenable_sriov().

We re-arrange the logic so that we call bnxt_ulp_start() and
bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and
bnxt_open().  The former is the normal coordinated firmware reset sequence
and the latter is firmware reset while the function is down.  This new
logic is now more straight forward and will now fix both scenarios.

Fixes: f3a6d206 ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.")
Reported-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Put the current logic in bnxt_open() to re-enable SRIOV after detecting
firmware reset into a new function bnxt_reenable_sriov().  This call
needs to be invoked in the firmware reset path also in the next patch.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Instead of switch_id, renaming it to dsn will be more meaningful
so that it can be used to display device serial number in follow up
patch via devlink_info command.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Latest kernels get the phys_port_name via devlink, if
ndo_get_phys_port_name is not defined. To provide the phys_port_name
correctly, register devlink before registering netdev.

Also call devlink_port_type_eth_set() after registering netdev as
devlink port updates the netdev structure and notifies user.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware bug has been fixed on B0 and newer chips, so disable the
workaround on these chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the only time we check and remove expired filters is
when we are inserting new filters.
Improving the aRFS expiry handling by adding code to do the above
work periodically.
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_rx_flow_steer(), if the dissected packet is a fragment, do not
proceed to create the ntuple filter and return error instead.  Otherwise
we would create a filter with 0 source and destination ports because
the dissected ports would not be available for fragments.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

575XX (P5) chips have the same UDP RSS hashing capability as P4 chips,
so we can enable it on P5 chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dev_port is meant to distinguish the network ports belonging to
the same PCI function.  Our devices only have one network port
associated with each PCI function and so we should not set it for
correctness.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the 2nd parameter fw_dflt is not set, we are calling bnxt_probe_phy()
after the firmware has reset.  There is no need to query the current
PHY settings from firmware as these settings may be different from
the ethtool settings that the driver will re-establish later.  So
return earlier in bnxt_probe_phy() to save one firmware call.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_update_phy_setting(), ethtool_get_link_ksettings() and
bnxt_disable_an_for_lpbk(), we inconsistently use netif_carrier_ok()
to determine link.  Instead, we should use bp->link_info.link_up
which has the true link state.  The netif_carrier state may be off
during self-test and while the device is being reset and may not always
reflect the true link state.

By always using bp->link_info.link_up, the code is now more
consistent and more correct.  Some unnecessary link toggles are
now prevented with this patch.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSN read can fail, for example on a kdump kernel without PCIe extended
config space support.  If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading.  Check the flag
to see if the stored DSN is valid before using it.  Only VF reps
creation should fail without valid DSN.

Fixes: 03213a99 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: NMarc Smith <msmith626@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running in XDP mode, pages come from the page pool, and should
be freed back to the same pool or specifically detached.  Currently,
when the driver re-initializes, the page pool destruction is delayed
forever since it thinks there are oustanding pages.

Fixes: 322b87ca ("bnxt_en: add page_pool support")
Signed-off-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return EINPROGRESS to devlink health reporter recover as we are not yet
done and call devlink_health_reporter_recovery_done once reset is
successfully completed from workqueue context.
Signed-off-by: NVikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock.  It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.

Fix by applying the corrected clamp value.

Fixes: 74706afa ("bnxt_en: Update interrupt coalescing logic.")
Signed-off-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This allows incrementing the correct timeout statistic without any mess.
Down the road, devices can learn to reset just the specific queue.

The patch was generated with the following script:

use strict;
use warnings;

our $^I = '.bak';

my @work = (
["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"],
["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"],
["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"],
["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"],
["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"],
["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"],
["drivers/net/appletalk/cops.c", "cops_timeout"],
["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"],
["drivers/net/arcnet/arcnet.c", "arcnet_timeout"],
["drivers/net/arcnet/com20020.c", "arcnet_timeout"],
["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"],
["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"],
["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"],
["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"],
["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"],
["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"],
["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"],
["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"],
["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"],
["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"],
["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"],
["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"],
["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"],
["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"],
["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"],
["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"],
["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"],
["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"],
["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"],
["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"],
["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"],
["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"],
["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"],
["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"],
["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"],
["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"],
["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"],
["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"],
["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"],
["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"],
["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"],
["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"],
["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"],
["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"],
["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"],
["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"],
["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"],
["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"],
["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"],
["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"],
["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"],
["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"],
["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"],
["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"],
["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"],
["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"],
["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"],
["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"],
["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"],
["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"],
["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"],
["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"],
["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"],
["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"],
["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"],
["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"],
["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"],
["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"],
["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"],
["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"],
["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"],
["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"],
["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"],
["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"],
["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"],
["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"],
["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"],
["drivers/net/ethernet/jme.c", "jme_tx_timeout"],
["drivers/net/ethernet/korina.c", "korina_tx_timeout"],
["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"],
["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"],
["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"],
["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"],
["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"],
["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"],
["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"],
["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"],
["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"],
["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"],
["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"],
["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"],
["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"],
["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"],
["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"],
["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"],
["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"],
["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"],
["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"],
["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"],
["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"],
["drivers/net/ethernet/realtek/atp.c", "tx_timeout"],
["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"],
["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"],
["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"],
["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"],
["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"],
["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"],
["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"],
["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"],
["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"],
["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"],
["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"],
["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"],
["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"],
["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"],
["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"],
["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"],
["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"],
["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"],
["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"],
["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"],
["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"],
["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"],
["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"],
["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"],
["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"],
["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"],
["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"],
["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"],
["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"],
["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"],
["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"],
["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"],
["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"],
["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"],
["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"],
["drivers/net/slip/slip.c", "sl_tx_timeout"],
["include/linux/usb/usbnet.h", "usbnet_tx_timeout"],
["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"],
["drivers/net/usb/catc.c", "catc_tx_timeout"],
["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"],
["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"],
["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"],
["drivers/net/usb/hso.c", "hso_net_tx_timeout"],
["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"],
["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"],
["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"],
["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"],
["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"],
["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"],
["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"],
["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"],
["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"],
["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"],
["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"],
["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"],
["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"],
["drivers/net/wan/cosa.c", "cosa_net_timeout"],
["drivers/net/wan/farsync.c", "fst_tx_timeout"],
["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"],
["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"],
["drivers/net/wan/x25_asy.c", "x25_asy_timeout"],
["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"],
["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"],
["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"],
["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"],
["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"],
["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"],
["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"],
["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"],
["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"],
["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"],
["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"],
["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"],
["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"],
["drivers/tty/synclink.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"],
["net/atm/lec.c", "lec_tx_timeout"],
["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"]
);

for my $p (@work) {
	my @pair = @$p;
	my $file = $pair[0];
	my $func = $pair[1];
	print STDERR $file , ": ", $func,"\n";
	our @ARGV = ($file);
	while (<ARGV>) {
		if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) {
			print STDERR "found $1+$2 in $file\n";
		}
		if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) {
			print STDERR "$func found in $file\n";
		}
		print;
	}
}

where the list of files and functions is simply from:

git grep ndo_tx_timeout, with manual addition of headers
in the rare cases where the function is from a header,
then manually changing the few places which actually
call ndo_tx_timeout.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NHeiner Kallweit <hkallweit1@gmail.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NShannon Nelson <snelson@pensando.io>
Reviewed-by: NMartin Habets <mhabets@solarflare.com>

changes from v9:
	fixup a forward declaration
changes from v9:
	more leftovers from v3 change
changes from v8:
        fix up a missing direct call to timeout
        rebased on net-next
changes from v7:
	fixup leftovers from v3 change
changes from v6:
	fix typo in rtl driver
changes from v5:
	add missing files (allow any net device argument name)
changes from v4:
	add a missing driver header
changes from v3:
        change queue # to unsigned
Changes from v2:
        added headers
Changes from v1:
        Fix errors found by kbuild:
        generalize the pattern a bit, to pick up
        a couple of instances missed by the previous
        version.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VF driver also needs to create the health reporters since
VFs are also involved in firmware reset and recovery.  Modify
bnxt_dl_register() and bnxt_dl_unregister() so that they can
be called by the VFs to register/unregister devlink.  Only the PF
will register the devlink parameters.  With devlink registered,
we can now create the health reporters on the VFs.

Fixes: 6763c779 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the logic to properly check the fw capabilities and create the
devlink health reporters only when needed.  The current code creates
the reporters unconditionally as long as bp->fw_health is valid, and
that's not correct.

Call bnxt_dl_fw_reporters_create() directly from the init and reset
code path instead of from bnxt_dl_register().  This allows the
reporters to be adjusted when capabilities change.  The same
applies to bnxt_dl_fw_reporters_destroy().

Fixes: 6763c779 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>