Adds two tests. One is a simple test to ensure that the new registers
LMRR and LMSER are properly maintained. The other actually uses the
existing EBB test infrastructure to test that LMRR and LMSER behave as
documented.
Signed-off-by: NJack Miller <jack@codezen.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This enables new registers, LMRR and LMSER, that can trigger an EBB in
userspace code when a monitored load (via the new ldmx instruction)
loads memory from a monitored space. This facility is controlled by a
new FSCR bit, LM.

This patch disables the FSCR LM control bit on task init and enables
that bit when a load monitor facility unavailable exception is taken
for using it. On context switch, this bit is then used to determine
whether the two relevant registers are saved and restored. This is
done lazily for performance reasons.
Signed-off-by: NJack Miller <jack@codezen.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This fixes a few issues with FSCR init and switching.

In commit 152d523e ("powerpc: Create context switch helpers
save_sprs() and restore_sprs()") we moved the setting of the FSCR
register from inside an CPU_FTR_ARCH_207S section to inside just a
CPU_FTR_ARCH_DSCR section. Hence we are setting FSCR on POWER6/7 where
the FSCR doesn't exist. This is harmless but we shouldn't do it.

Also, we can simplify the FSCR context switch. We don't need to go
through the calculation involving dscr_inherit. We can just restore
what we saved last time.

We also set an initial value in INIT_THREAD, so that pid 1 which is
cloned from that gets a sane value.

Based on patch by Jack Miller.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Current comment in the early_setup_secondary() for paca->soft_enabled
update is misleading. Comment should say to Mark interrupts "disabled"
instead of "enabled". Fix the typo.
Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fixes the following testsuite failure:

  $ sudo ./perf test -v kallsyms
   1: vmlinux symtab matches kallsyms                          :
  --- start ---
  test child forked, pid 12489
  Using /proc/kcore for kernel object code
  Looking at the vmlinux_path (8 entries long)
  Using /boot/vmlinux for symbols
  0xc00000000003d300: diff name v: .kretprobe_trampoline_holder k: kretprobe_trampoline
  Maps only in vmlinux:
   c00000000086ca38-c000000000879b6c 87ca38 [kernel].text.unlikely
   c000000000879b6c-c000000000bf0000 889b6c [kernel].meminit.text
   c000000000bf0000-c000000000c53264 c00000 [kernel].init.text
   c000000000c53264-d000000004250000 c63264 [kernel].exit.text
   d000000004250000-d000000004450000 0 [libcrc32c]
   d000000004450000-d000000004620000 0 [xfs]
   d000000004620000-d000000004680000 0 [autofs4]
   d000000004680000-d0000000046e0000 0 [x_tables]
   d0000000046e0000-d000000004780000 0 [ip_tables]
   d000000004780000-d0000000047e0000 0 [rng_core]
   d0000000047e0000-ffffffffffffffff 0 [pseries_rng]
  Maps in vmlinux with a different name in kallsyms:
  Maps only in kallsyms:
   d000000000000000-f000000000000000 1000000000010000 [kernel.kallsyms]
   f000000000000000-ffffffffffffffff 3000000000010000 [kernel.kallsyms]
  test child finished with -1
  ---- end ----
  vmlinux symtab matches kallsyms: FAILED!

The problem is that the kretprobe_trampoline symbol looks like this:

  $ eu-readelf -s /boot/vmlinux G kretprobe_trampoline
   2431: c000000001302368     24 NOTYPE  LOCAL  DEFAULT       37 kretprobe_trampoline_holder
   2432: c00000000003d300      8 FUNC    LOCAL  DEFAULT        1 .kretprobe_trampoline_holder
  97543: c00000000003d300      0 NOTYPE  GLOBAL DEFAULT        1 kretprobe_trampoline

Its type is NOTYPE, and its size is 0, and this is a problem because
symbol-elf.c:dso__load_sym skips function symbols that are not STT_FUNC
or STT_GNU_IFUNC (this is determined by elf_sym__is_function). Even
if the type is changed to STT_FUNC, when dso__load_sym calls
symbols__fixup_duplicate, the kretprobe_trampoline symbol is dropped in
favour of .kretprobe_trampoline_holder because the latter has non-zero
size (as determined by choose_best_symbol).

With this patch, all vmlinux symbols match /proc/kallsyms and the
testcase passes.

Commit c1c355ce ("x86/kprobes: Get rid of
kretprobe_trampoline_holder()") gets rid of kretprobe_trampoline_holder
altogether on x86. This commit does the same on powerpc. This change
introduces no regressions on the perf and ftracetest testsuite results.
Reviewed-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NThiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On Book3E CPUs (and possibly other configs), it is possible to have SRIOV
(CONFIG_PCI_IOV) set without CONFIG_EEH.  The SRIOV code does not check
for this, and if EEH is disabled, pci_dn.c fails to build.

Fix this by gating the EEH-specific code in the SRIOV implementation
behind CONFIG_EEH.

Fixes: 39218cd0 ("powerpc/eeh: EEH device for VF")
Reported-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On bare-metal, when a device is attached to the cxl card, lsvpd shows
a location code such as (with cxlflash):
     # lsvpd -l sg22
     ...
     *YL U78CB.001.WZS0073-P1-C33-B0-T0-L0
which makes it hard to easily identify the cxl adapter owning the
flash device, since in this example C33 refers to a P8 processor.

lsvpd looks in the parent devices until it finds a location code, so the
device node for the vPHB ends up being used.

By reusing the device node of the adapter for the vPHB, lsvpd shows:
     # lsvpd -l sg16
     ...
     *YL U78C9.001.WZS09XA-P1-C7-B1-T0-L3
where C7 is the PCI slot of the cxl adapter.

On powerVM, the vPHB was already using the adapter device node, so
there's no change there.

Tested by cxlflash on bare-metal and powerVM.
Signed-off-by: NFrederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds support for using CAPP DMA mode, which is required for XSL
based cards such as the Mellanox CX4 to function.

This is currently an RFC as it depends on the corresponding support to
be merged into skiboot first, which was submitted here:
http://patchwork.ozlabs.org/patch/625582/

In the event that the skiboot on the system does not have the above
support, it will indicate as such in the kernel log and abort the init
process.
Signed-off-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The XSL (Translation Service Layer) is a stripped down version of the
PSL (Power Service Layer) used in some cards such as the Mellanox CX4.

Like the PSL, it implements the CAIA architecture, but has a number of
differences, mostly in it's implementation dependent registers. This
adds an ops structure to abstract these differences to bring initial
support for XSL CAPI devices.

The XSL does not implement the optional architected SERR register,
however while it treats it as a reserved register and should work with
no special treatment, attempting to access it will cause the XSL_FEC
(First Error Capture) register to be filled out, preventing it from
capturing any subsequent errors. Therefore, this patch also prevents the
kernel from trying to set up the SERR register so that the FEC register
may still be useful, and to save one interrupt.

The XSL also uses a special DMA cxl mode, which uses a slightly
different init sequence for the CAPP and PHB. The kernel support for
this will be in a future patch once the corresponding support has been
merged into skiboot.
Co-authored-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In the kernel API, it is possible to attempt to allocate AFU interrupts
after already starting a context. Since the process element structure
used by the hardware is only filled out at the time the context is
started, it will not be updated with the interrupt numbers that have
just been allocated and therefore AFU interrupts will not work unless
they were allocated prior to starting the context.

This can present some difficulties as each CAPI enabled PCI device in
the kernel API has a default context, which may need to be started very
early to enable translations, potentially before interrupts can easily
be set up.

This patch makes the API more flexible to allow interrupts to be
allocated after a context has already been started and takes care of
updating the PE structure used by the hardware and notifying it to
discard any cached copy it may have.

The update is currently performed via a terminate/remove/add sequence.
This is necessary on some hardware such as the XSL that does not
properly support the update LLCMD.

Note that this is only supported on powernv at present - attempting to
perform this ordering on PowerVM will raise a warning.
Signed-off-by: NIan Munsie <imunsie@au1.ibm.com>
Reviewed-by: NFrederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Make a couple more variables static. Found by sparse.
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: fbarrat@linux.vnet.ibm.com
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sparse complains that it doesn't know what REG_BYTE is:

  arch/powerpc/kernel/align.c:313:29: error: undefined identifier 'REG_BYTE'

REG_BYTE is defined differently based on whether we're compiling for
LE, BE32 or BE64. Sparse apparently doesn't provide __BIG_ENDIAN__ or
__LITTLE_ENDIAN__, which means we get no definition.

Rather than check for __BIG_ENDIAN__ and then separately for
__LITTLE_ENDIAN__, just switch the #ifdef to check for __BIG_ENDIAN__
and then #else we define the little endian version. Technically that's
dicey because PDP_ENDIAN is also a possibility, but we already do it in
a lot of places so one more hardly matters.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sometimes headers that provide prototypes for functions are
accidentally omitted from the files that define the functions.

Fix a couple of times that occurs.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sparse picked up a number of functions that are implemented in C and
then only referred to in asm code.

This introduces asm-prototypes.h, which provides a place for
prototypes of these functions.

This silences some sparse warnings.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
[mpe: Add include guards, clean up copyright & GPL text]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This is just a smattering of things picked up by sparse that should
be made static.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The array crash_shutdown_handles is an array of size CRASH_HANDLER_MAX+1
containing up to CRASH_HANDLER_MAX shutdown_handlers. It is assumed to
be NULL terminated, which it is under normal circumstances. Array
accesses in the functions crash_shutdown_unregister() and
default_machine_crash_shutdown() rely on this NULL termination property
when traversing this list and don't protect again out of bounds accesses.
If the NULL terminator were somehow overwritten these functions could
potentially access out of the bounds of the array.

Shrink the array to size CRASH_HANDLER_MAX and implement explicit array
bounds checking when accessing the elements of the
crash_shutdown_handles[] array in crash_shutdown_unregister() and
default_machine_crash_shutdown().
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The mm zone mechanism was traditionally used by arch specific code to
partition memory into allocation zones. However there are several zones
that are managed by the mm subsystem rather than the architecture. Most
architectures set the max PFN of these special zones to zero, however on
powerpc we set them to ~0ul. This, in conjunction with a bug in
free_area_init_nodes() results in all of system memory being placed in
ZONE_DEVICE when enabled. Device memory cannot be used for regular kernel
memory allocations so this will cause a kernel panic at boot. Given the
planned addition of more mm managed zones (ZONE_CMA) we should aim to be
consistent with every other architecture and set the max PFN for these
zones to zero.
Signed-off-by: NOliver O'Halloran <oohall@gmail.com>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

THREAD_DSCR:
  Added in efcac658 "powerpc: Per process DSCR + some fixes (try#4)"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_DSCR_INHERIT:
  Added in 71433285 "powerpc: Restore correct DSCR in context switch"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_TAR:
  Added in 2468dcf6 "powerpc: Add support for context switching the TAR register"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_BESCR, THREAD_EBBHR and THREAD_EBBRR:
  Added in 9353374b "powerpc: Context switch the new EBB SPRs"
  Last usage removed in 152d523e "powerpc: Create context switch helpers save_sprs() and restore_sprs()"

THREAD_SIAR, THREAD_SDAR, THREAD_SIER, THREAD_MMCR0, and THREAD_MMCR2:
  Added in 59affcd3 "powerpc: Context switch more PMU related SPRs"
  Last usage removed in b11ae951 "powerpc: Partial revert of "Context switch more PMU related SPRs""

PACA_LOCK_TOKEN:
  Added in 9e368f29 "KVM: PPC: book3s_hv: Add support for PPC970-family processors"
  Last usage removed in c17b98cf "KVM: PPC: Book3S HV: Remove code for PPC970 processors"

HCALL_STAT_SIZE, HCALL_STAT_CALLS, HCALL_STAT_TB and HCALL_STAT_PURR:
  Added in 57852a85 "[POWERPC] powerpc: Instrument Hypervisor Calls"
  Last usage removed in c8cd093a "powerpc: tracing: Add hypervisor call tracepoints"

VCPU_EPLC:
  Added in d30f6e48 "KVM: PPC: booke: category E.HV (GS-mode) support"
  Never used.

CPU_DOWN_FLUSH:
  Added in e7affb1d "powerpc/cache: add cache flush operation for various e500"
  Never used.

CFG_STAMP_XSEC:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Last usage removed in 0e469db8 "powerpc: Rework VDSO gettimeofday to prevent time going backwards"

KVM_LPCR:
  Added in aa04b4cc "KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests"
  Last usage removed in a0144e2a "KVM: PPC: Book3S HV: Store LPCR value for each virtual core"

GPR15, GPR16, GPR17, GPR18, GPR19, GPR20, GPR21, GPR22, GPR23, GPR24,
GPR25, GPR26, GPR27, GPR28, GPR29, GPR30 and GPR31:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Never used.

VCPU_SHADOW_FSCR:
  Added in 616dff86 "KVM: PPC: Book3S PR: Handle Facility interrupt and FSCR"
  Never used.

VCPU_SHADOW_SRR1:
  Added in a2d56020 "KVM: PPC: Book3S PR: Keep volatile reg values in vcpu rather than shadow_vcpu"
  Never used.

KVM_SPLIT_SIZE:
  Added in b4deba5c "KVM: PPC: Book3S HV: Implement dynamicmicro-threading on POWER8"
  Never used.

VCPU_VCPUID:
  Added in de56a948 "KVM: PPC: Add support for Book3S processors in hypervisor mode"
  Last usage removed 1b400ba0 "KVM: PPC: Book3S HV: Improve handling of local vs. global TLB invalidations"

_MQ:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Never used.

AUDITCONTEXT:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Last usage removed in 401d1f02 "[PATCH] syscall entry/exit revamp"

CLONE_VM:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Currently unused.

CLONE_UNTRACED:
  Added in 14cf11af "powerpc: Merge enough to start building in arch/powerpc."
  Currently unused.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
[mpe: Munge change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

memory_hotplug_max() uses hot_add_drconf_memory_max() to get maxmimum
addressable memory by referring to ibm,dyanamic-memory property. There
are three problems with the current approach:

1 hot_add_drconf_memory_max() assumes that ibm,dynamic-memory includes
  all the LMBs of the guest, but that is not true for PowerKVM which
  populates only DR LMBs (LMBs that can be hotplugged/removed) in that
  property.
2 hot_add_drconf_memory_max() multiplies lmb-size with lmb-count to arrive
  at the max possible address. Since ibm,dynamic-memory doesn't include
  RMA LMBs, the address thus obtained will be less than the actual max
  address. For example, if max possible memory size is 32G, with lmb-size
  of 256MB there can be 127 LMBs in ibm,dynamic-memory (1 LMB for RMA
  which won't be present here).  hot_add_drconf_memory_max() would then
  return the max addressable memory as 127 * 256MB = 31.75GB, the max
  address should have been 32G which is what ibm,lrdr-capacity shows.
3 In PowerKVM, there can be a gap between the end of boot time RAM and
  beginning of hotplug RAM area. So just multiplying lmb-count with
  lmb-size will not provide the correct max possible address for PowerKVM.

This patch fixes 1 by using ibm,lrdr-capacity property to return the max
addressable memory whenever the property is present. Then it fixes 2 & 3
by fetching the address of the last LMB in ibm,dynamic-memory property.

Fixes: cd34206e ("powerpc: Add memory_hotplug_max()")
Signed-off-by: NBharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NBharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There is an ordering issue with spin_unlock_wait() on powerpc, because
the spin_lock primitive is an ACQUIRE and an ACQUIRE is only ordering
the load part of the operation with memory operations following it.
Therefore the following event sequence can happen:

CPU 1			CPU 2			CPU 3

==================	====================	==============
						spin_unlock(&lock);
			spin_lock(&lock):
			  r1 = *lock; // r1 == 0;
o = object;		o = READ_ONCE(object); // reordered here
object = NULL;
smp_mb();
spin_unlock_wait(&lock);
			  *lock = 1;
smp_mb();
o->dead = true;         < o = READ_ONCE(object); > // reordered upwards
			if (o) // true
				BUG_ON(o->dead); // true!!

To fix this, we add a "nop" ll/sc loop in arch_spin_unlock_wait() on
ppc, the "nop" ll/sc loop reads the lock
value and writes it back atomically, in this way it will synchronize the
view of the lock on CPU1 with that on CPU2. Therefore in the scenario
above, either CPU2 will fail to get the lock at first or CPU1 will see
the lock acquired by CPU2, both cases will eliminate this bug. This is a
similar idea as what Will Deacon did for ARM64 in:

  d86b8da0 ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")

Furthermore, if the "nop" ll/sc figures out the lock is locked, we
actually don't need to do the "nop" ll/sc trick again, we can just do a
normal load+check loop for the lock to be released, because in that
case, spin_unlock_wait() is called when someone is holding the lock, and
the store part of the "nop" ll/sc happens before the lock release of the
current lock holder:

	"nop" ll/sc -> spin_unlock()

and the lock release happens before the next lock acquisition:

	spin_unlock() -> spin_lock() <next holder>

which means the "nop" ll/sc happens before the next lock acquisition:

	"nop" ll/sc -> spin_unlock() -> spin_lock() <next holder>

With a smp_mb() preceding spin_unlock_wait(), the store of object is
guaranteed to be observed by the next lock holder:

	STORE -> smp_mb() -> "nop" ll/sc
	-> spin_unlock() -> spin_lock() <next holder>

This patch therefore fixes the issue and also cleans the
arch_spin_unlock_wait() a little bit by removing superfluous memory
barriers in loops and consolidating the implementations for PPC32 and
PPC64 into one.
Suggested-by: N"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: NBoqun Feng <boqun.feng@gmail.com>
Reviewed-by: N"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
[mpe: Inline the "nop" ll/sc loop and set EH=0, munge change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Since the pstore code has moved away from nvram.c, remove unused
pstore headers pstore.h and kmsg_dump.h.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We're approaching 20 locations where we need to check for ELF ABI v2.
That's fine, except the logic is a bit awkward, because we have to check
that _CALL_ELF is defined and then what its value is.

So check it once in asm/types.h and define PPC64_ELF_ABI_v2 when ELF ABI
v2 is detected.

We also have a few places where what we're really trying to check is
that we are using the 64-bit v1 ABI, ie. function descriptors. So also
add a #define for that, which simplifies several checks.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code. XICS is now the only supported interrupt controller for
pSeries so do some cleanups too.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code. XICS is now the only supported interrupt controller for
pSeries so do some cleanups too.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so remove MPIC
code. XICS is now the only supported interrupt controller for
pSeries so do some cleanups too.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

MPIC was only used by Power3 which is now unsupported, so drop support
for MPIC. XICS is now the only supported interrupt controller for
pSeries so make the XICS functions generic.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

sub_reloc_offset() has not been used since commit
917f0af9 ("powerpc: Remove arch/ppc and include/asm-ppc") which
removed include/asm-ppc/prom.h.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Align the hot loops in our assembly implementation of strncpy(),
strncmp() and memchr().
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

A number of our assembly implementations of string functions do not
align their hot loops. I was going to align them manually, but I
realised that they are are almost instruction for instruction
identical to what gcc produces, with the advantage that gcc does
align them.

In light of that, let's just remove the assembly versions.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In setup_sigcontext(), we set current->thread.vrsave then use it
straight after. Since current is hidden from the compiler via inline
assembly, it cannot optimise this and we end up with a load hit store.

Fix this by using a temporary.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In both __giveup_fpu() and __giveup_altivec() we make two modifications
to tsk->thread.regs->msr. gcc decides to do a read/modify/write of
each change, so we end up with a load hit store:

        ld      r9,264(r10)
        rldicl  r9,r9,50,1
        rotldi  r9,r9,14
        std     r9,264(r10)
...
        ld      r9,264(r10)
        rldicl  r9,r9,40,1
        rotldi  r9,r9,24
        std     r9,264(r10)

Fix this by using a temporary.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Pull thermal management fixes from Zhang Rui:

 - fix an ordering issue in cpu cooling that cooling device is
   registered before it's ready (freq_table being populated).
   (Lukasz Luba)

 - fix a missing comment update (Caesar Wang)

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: add the note for set_trip_temp
  thermal: cpu_cooling: fix improper order during initialization

Pull block layer fixes from Jens Axboe:
 "A small collection of fixes for the current series.  This contains:

   - Two fixes for xen-blkfront, from Bob Liu.

   - A bug fix for NVMe, releasing only the specific resources we
     requested.

   - Fix for a debugfs flags entry for nbd, from Josef.

   - Plug fix from Omar, fixing up a case of code being switched between
     two functions.

   - A missing bio_put() for the new discard callers of
     submit_bio_wait(), fixing a regression causing a leak of the bio.
     From Shaun.

   - Improve dirty limit calculation precision in the writeback code,
     fixing a case where setting a limit lower than 1% of memory would
     end up being zero.  From Tejun"

* 'for-linus' of git://git.kernel.dk/linux-block:
  NVMe: Only release requested regions
  xen-blkfront: fix resume issues after a migration
  xen-blkfront: don't call talk_to_blkback when already connected to blkback
  nbd: pass the nbd pointer for flags debugfs
  block: missing bio_put following submit_bio_wait
  blk-mq: really fix plug list flushing for nomerge queues
  writeback: use higher precision calculation in domain_dirty_limits()

Pull GPIO fixes from Linus Walleij:
 "A new bunch of GPIO fixes for v4.7.

  This time I am very grateful that Ricardo Ribalda Delgado went in and
  fixed my stupid refcounting mistakes in the removal path for GPIO
  chips.  I had a feeling something was wrong here and so it was.  It
  exploded on OMAP and it fixes their problem.  Now it should be (more)
  solid.

  The rest i compilation, Kconfig and driver fixes.  Some tagged for
  stable.

  Summary:

   - Fix a NULL pointer dereference when we are searching the GPIO
     device list but one of the devices have been removed (struct
     gpio_chip pointer is NULL).

   - Fix unaligned reference counters: we were ending on +3 after all
     said and done.  It should be 0.  Remove an extraneous get_device(),
     and call cdev_del() followed by device_del() in gpiochip_remove()
     instead and the count goes to zero and calls the release() function
     properly.

   - Fix a compile warning due to a missing #include in the OF/device
     tree portions.

   - Select ANON_INODES for GPIOLIB, we're using that for our character
     device.  Some randconfig tests disclosed the problem.

   - Make sure the Zynq driver clock runs also without CONFIG_PM enabled

   - Fix an off-by-one error in the 104-DIO-48E driver

   - Fix warnings in bcm_kona_gpio_reset()"

* tag 'gpio-v4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: bcm-kona: fix bcm_kona_gpio_reset() warnings
  gpio: select ANON_INODES
  gpio: include <linux/io-mapping.h> in gpiolib-of
  gpiolib: Fix unaligned used of reference counters
  gpiolib: Fix NULL pointer deference
  gpio: zynq: initialize clock even without CONFIG_PM
  gpio: 104-dio-48e: Fix control port offset computation off-by-one error

Pull SCSI fixes from James Bottomley:
 "Two current fixes:

   - one affects Qemu CD ROM emulation, which stopped working after the
     updates in SCSI to require VPD pages from all conformant devices.

     Fix temporarily by blacklisting Qemu (we can relax later when they
     come into compliance).

   - The other is a fix to the optimal transfer size.  We set up a
     minefield for ourselves by being confused about whether the limits
     are in bytes or sectors (SCSI optimal is in blocks and the queue
     parameter is in bytes).

     This tries to fix the problem (wrong setting for queue limits
     max_sectors) and make the problem more obvious by introducing a
     wrapper function"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  sd: Fix rw_max for devices that report an optimal xfer size
  scsi: Add QEMU CD-ROM to VPD Inquiry Blacklist