Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This could lead userspace initram images getting
built without necessary firmware files included
leading to probing failures of ath10k on boot with
QCA61X4.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In some cases some channel survey data was
reported incorrect.

Channel info events were expected to come in pairs
without and with COMPLETE flag set respectively
for each channel visit during scan.

The known deviation from this is rule for last
scan chan info and first (next) scan chan info
both have COMPLETE flag set. This was either
programmed with the intent of providing BSS cycle
count info or this is an artefact of firmware scan
state machine. Either way this is useless due to
short wraparound time, wraparound quirks and no
overflow notification.

Survey dumps now include only data gathered during
scan channel visits that can be computed
correctly.

This should improve hostapd ACS a little bit.
Reported-by: NSrinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.

Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.

This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.

This should improve hostapd ACS a little bit.
Reported-by: NSrinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.

Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change more netdev_dbg statements over to netif_dbg and add some new
netif_dbg statements to the driver.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.

Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device private data structure contains all the defined hardware
features for the device. However one of the features is not set. Even
though the feature is not currently used, set it to avoid future
issues of the feature being checked thinking it has been properly set.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.

SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's legal for drivers to provide the QP port through the
QPC schedule-queue field on the reset-to-init QP state change.

Add adjusting of the schedule queue port in the SRIOV wrapper
for that operation too.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some VF drivers flow set the schedule queue in the QP context but
without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH.

To allow for such non-modified drivers to function as single ported
IB VFs, we must adjust the schedule queue port whenever being set,
e.g as currently done for single ported Eth VFs.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.

This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.

(1) make sure that events are generated only for VFs sitting on
    the relevant physical port (under the ALL_SLAVES flow).

(2) before generating the event, convert from physical (one or two)
    to VF port (always equals one).
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Single port VFs always provide port = 1 (even if the actual physical
port used is port 2). As such, we need to convert the port provided
by the VF to the physical port before calling into the firmware.

It turns out that the Linux mlx4 VF RoCE driver maintains a copy of
the GID table and hence this change became critical only for single
ported IB VFs, but it could be needed for other RoCE VF drivers too.

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the Zynq TRM, gigabit half duplex is not supported.  Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead.  So the tx_bytes pointer increases by about
2^32 for every transmitted frame.

Fix by calculating the delta as a signed long.

Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: NFlorian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.

However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.

Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.

Currently the sleep threshold/grace period is at a
very conservative value of 60ms.

Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.

Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.

The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.

This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is actually safe to enable ASPM after the
device is booted up.

This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix format specifier used for dma_addr_t, namely use %pad
Debug print virtual address for the same buffer as well.

Fixes: dc16427b ("wil6210: Add pmc debug mechanism memory management")
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since the caller already check the presence of a of_node there
is no need to repeat the check in stmmac_probe_config_dt.

There is also no point in checking the return value of the
of_match_device function since if there wasn't match in the
first place we would never be in this function.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since stmmac_dvr_probe takes care of setting driver data and
assign resources to the priv structure there is no need to
access the priv structure from the other probe functions.
This mean that this function can be changed into just return
an int and thus simplifying the callers.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Creat a struct that contain all the resources that needs to be
assigned to the priv struct in stmmac_dvr_probe. This makes it
possible to factor out more common code from the other probe
functions and also use this struct to hold the resources as
they are fetched.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move setting of driver data into stmmac_dvr_probe so the
other probe functions don't have to. This will help to
simplify the other probe functions later.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove some T4/T5 registers that were included incorrectly.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a set_mac_address() NIC-type function for EF10 only, and
use this to set the MAC address on the vadaptor. For Siena and
earlier, the MAC address continues to be set by MC_CMD_SET_MAC;
this is still called on EF10, and including a MAC address in
this command has no effect.

The sriov_mac_address_changed() NIC-type function is no longer
needed on EF10, but it is needed for Siena where it is used to
update the peer address of the PF for VFDI.  Change this to use
the new set_mac_address function pointer.

efx_ef10_sriov_mac_address_changed() is no longer called, as VFs
will try to change the MAC address on their vadaptor rather than
trying to change to the context of the PF to alter the vport.

When a VF is running in direct passthrough mode with MAC spoofing
enabled, it will be able to change the MAC address on its vadaptor.
In this case, there is a link to the PF, so find the correct VF in
its ef10_vf array and update the MAC address.

ndo_set_mac_address() can be called during driver unload while
bonding, and in this case the device has already been stopped, so
don't call efx_net_open() to restart it after reconfiguration.

efx->port_enabled is set to false in efx_stop_port(), so it is
indicator of whether the device needs to be restarted.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Exercised with
"ip link set <PF intf> vf <vf_i> state {auto|enable|disable}"
Sets the reporting policy for VF link state to either
 - mirror physical link state
 - always up
 - always down

get VF link state mode in efx_ef10_sriov_get_vf_config

Exercised by
"ip link show <PF intf>";
output will include a line like
vf 0 MAC 12:34:56:78:9a:bc, link-state auto
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The max vlan tags that can be offloaded is 2, including any upstream VLAN
aggregator. Currently there is no way for the net driver to know whether
the upstream vswitch (if any) is using vlan tags, so there is no way to
know how many tags we can request.
Along with the implementation for the ndo_set_vf_vlan callback, this patch
also adds 2 VLAN tags for the driver created VEB switch if possible, that
way it is possible to offload as many tags as are allowed.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we do an entity reset when we detect an MC reboot.
This messes up SRIOV because it leaves VFs orphaned. The extra
reset is rather redundant anyway, since the MC reboot will have
basically reset everything.

This change replaces the entity reset after MC reboot with a
simpler datapath reset that reallocates resources but doesn't
perform the entity reset.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtnetlink calls ndo_get_vf_config when compiling information
about a network interface, so that the VFs associated with a PF
can be listed (eg: ip link show).
Implement a response to this entry point and return PF-set MAC
address for VF in ndo_get_vf_config
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement a response to this entrypoint.
The ndo_set_vf_mac() entrypoint is only exposed in the driver if
CONFIG_SFC_SRIOV is defined.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to avoid MC bugs the flags field needs to be set to 0.
Instead of explicitly clearing out the flags individually, a
better way to do this is to memset the MCDI_BUF to 0.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A VF's MAC address is set by its parent PF and added to its vport.
To get this MAC address, the VF must use MC_CMD_ VPORT_GET_MAC_ADDRESSES.
In the current scheme, a VF's vport should only have one MAC address,
so warn if this is not the case.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If MCDI timeouts are encountered during efx_ef10_filter_table_remove(),
an FLR will be queued, but efx->filter_state will still be kfree()d.
The queued FLR will then call efx_ef10_filter_table_restore(), which
will try to use efx->filter_state. This previously caused a panic.
This patch adds an rwsem to protect the existence of efx->filter_state,
separately from the spinlock protecting its contents.  Users which can
race against efx_ef10_filter_table_remove() should down_read this rwsem.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialised in efx_probe_vf and removal is dealt with in
efx_ef10_remove.

vf->efx is needed in future patches to change the MAC address
of the VF via the parent PF, while the driver is bound to the
VF.
Example: ip link set dev vf NUM mac LLADDR
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise the PF and VF can disagree on the VF's MAC address and
this leads to strange behaviour, up to and including kernel panics.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>