While working on getting my rtl8821au driver in pretty shape for
inclusion, it is dicosvered that the tm_trigger flag is used only for
the first device using this driver.
This flag handles the thermal power management in the hardware.

To change this add a entry in sttruct rtl_dm, so each device can handle
is separately.
Signed-off-by: NHans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

in the rtlwifi/rtl8192cu, INTF_PCI and INTF_USB is unnecessary.
because RTL8192CU chipset is only USB interface.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is
same routine. I remove both functions. then i add
_rtl92cu_init_beacon_parameters() in the hw.c.
_rtl92cu_init_beacon_parameters() is same routine with
_InitBeaconParameters().
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

in the rtlwifi/rtl8192cu, IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU
is unnecessary. because rtlwifi/rtl8192cu codes aren't shared.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This extension of BCMA_DRIVER_PCI has no reason to depend on
BCMA_HOST_PCI. User may just want to have PCI device attached to SoC
registered without enabling any extra client mode code.
This can be useful when having non-bcma PCI device attached or when
using other PCI driver.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It seems Broadcom released two devices with conflicting device id. There
are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they
can be found in routers, e.g. Netgear WNR834Bv2. However, according to
Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY).
It's unsure if they meant PCI device id, or "virtual" id (from SPROM).
To distinguish these devices lets check PHY type (G vs. N).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As we plan to add support for platform NVRAM we should store direct
data pointer without the extra struct firmware layer. This will allow
us to support other sources with the only requirement being u8 buffer.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Most drivers use FIF_OTHER_BSS to set promiscous mode.  Let us
follow their lead even though it doesn't match exactly the HW
filter flags.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make sure .disconnect() doesn't cleanup the device if
.resume() failed.  This may happen when device is removed
during suspend.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Users of older Ralink devices report that received frames
sometimes have zero length.  Watch out for that.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This allows e.g. user space to use /sys/class/ieee80211/*/macaddress
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Recently Broadcom added support for NVRAMs with entries for multiple
PCIe devices. One of the supported formats is based on prefixes defined
like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc.

Unfortunately there are also a bit older devices using different way of
defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries:
devpath0=pci/1/1/
devpath1=pci/2/1
Broadcom stated this old format will never be used/supported by brcmfmac
but given the simplicity of this patch I'll insist on supporting it.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes semantic warning for debugging data dump feature.
Previous code is based on the assumption that skb is not null.
New change makes sure that we already have data buffer.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

After physical reconnect, the rtl8192cu chipset shows low
transmission rates.It cause is that variable "iqk_initialized"
do not de-initialized. So I add this code.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Negative adapter->tx_pending is observed while running data traffic,
because tx_pending is decreased once more for AMSDU packet.

since tx_pending have been decreased for all the source MSDU packets,
we don't need to update once more for AMSDU packet.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes issue with the accessing correct ra_list by
downgrading corresponding tid number.

Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue
using downgraded tid number.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This was missing and would cause issue in WMM handling.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This would enable driver to enter powersave as soon as connected.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NXinmin Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes an issue where we were still setting 11h_active
flag to true for channel defs where DFS is not required.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

BSS reset would reset all state information in FW.
Issue 11d config command after reset to enabled 11d in FW.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This would enable clearing of FW bss data structures when AP
operations are stopped.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Correct bss_type assignment in add_virtual_interface.
This would ensure correct operation in multiple station scenarios.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds more detailed information about association failures
 - reason and states.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Delete jump to a label on the next line, when that label is not
used elsewhere.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier l;
@@

-if (...) goto l;
-l:
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.

This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():

if (th->doff < sizeof(struct tcphdr) / 4)
    goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
    goto discard_it;

So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.

if (skb->len < tcp_hdrlen(skb) || ...)
	goto csum_err;

A second check can be removed after no_tcp_socket label for same reason.

Same tests can be removed in tcp_v6_do_rcv()

Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.
Signed-off-by: NEric Dumazet  <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Scott Feldman says:

====================
switchdev: documentation updates

Update the switchdev documentation to clarify that for IPV4 FIB object, the add
op is used for both adding and modifying the FIB entry on the device.

I found a few other white-space and grammer issues to fix, and to clarify the
static FDB ops.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.

Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>