After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mfd/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NLee Jones <lee.jones@linaro.org>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/misc/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.

Make these changes everywhere under drivers/media/.
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NKamil Debski <k.debski@samsung.com>
Acked-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.

Make these changes in 2 files under drivers/input/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NFerruh Yigit <fery@cypress.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/iio/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Do that for the omap_ssi driver.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-By: NSebastian Reichel <sre@kernel.org>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/hid/i2c-hid/i2c-hid.c.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in 4 files under
gpu/drm/exynos/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/gpio/gpio-omap.c.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

CONFIG_PM is defined as the alternative of CONFIG_PM_RUNTIME and
CONFIG_PM_SLEEP, so it can be used instead of that.

Besides, after commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
using the alternative isn't even necessary.

Use CONFIG_PM instead of it in drivers/char/hw_random/exynos-rng.c.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM (or even dropped in some cases).

Replace CONFIG_PM_RUNTIME with CONFIG_PM in the USB core code
and documentation.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.

However, after commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.

For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PCI core code.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in the ACPI core code.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM or even may be dropped entirely in some cases.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PM core code.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

We currently trigger BUG when VIRTIO_NET_F_CTRL_VQ
is not set but one of features depending on it is.
That's not a friendly way to report errors to
hypervisors.
Let's check, and fail probe instead.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Peer priority groups were being reversed, but this was missed in the previous
fix sent out for this issue.

v2 : Previous patch was doing extra unnecessary work, result is the same.
Please ignore previous patch

Fixes :	ee7bc3cd ('cxgb4 : dcb open-lldp interop fixes')
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pptp_getname() only partially initializes the stack variable sa,
particularly only fills the pptp part of the sa_addr union. The code
thereby discloses 16 bytes of kernel stack memory via getsockname().

Fix this by memset(0)'ing the union before.

Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.

This issue was revealed by kbuild testing
when <asm/unaligned.h> was added in <linux/ieee80211.h>
resulting in redefinition of get_unaligned_be16 (and
probably others).

Cc: stable@vger.kernel.org # v3.17
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Value needs to be swapped on BE.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Just use the acpi interface.  That's what windows uses on this
generation and it's the only thing that seems to work reliably
on these generation parts.

You can still force the native backlight interface by setting
radeon.backlight=1

Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=88501

v2: merge into above if/else block
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The /aliases node isn't always present in the device tree, but the
unittest code assumes that /aliases is there. Add a check when inserting
the testcase data to see if of_aliases needs to be updated, and undo the
settings when the nodes are removed.
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org>

isert has an issue of trying to create a CQ with more CQEs than are
supported by the hardware, that currently results in failures during
isert_device creation during first session login.

This is the isert version of the patch that Minh Tran submitted for
iser, and is simple a workaround required to function with existing
ocrdma hardware.
Signed-off-by: NChris Moore <chris.moore@emulex.com>
Reviewied-by: NSagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

As reported by Dmitry, on some Chromebooks there are devices with
corresponding ACPI objects and with unusual system wakeup
configuration.  Namely, they technically are wakeup-capable, but the
wakeup is handled via a platform-specific out-of-band mechanism and
the ACPI PM layer has no information on the wakeup capability.  As
a result, device_may_wakeup(dev) called from acpi_dev_suspend_late()
returns 'true' for those devices, but the wakeup.flags.valid flag is
unset for the corresponding ACPI device objects, so acpi_device_wakeup()
reproducibly fails for them causing acpi_dev_suspend_late() to return
an error code.  The entire system suspend is then aborted and the
machines in question cannot suspend at all.

Address the problem by ignoring the device_may_wakeup(dev) return
value in acpi_dev_suspend_late() if the ACPI companion of the device
being handled has wakeup.flags.valid unset (in which case it is clear
that the wakeup is supposed to be handled by other means).

This fixes a regression introduced by commit a76e9bd8 (i2c:
attach/detach I2C client device to the ACPI power domain) as the
affected systems could suspend and resume successfully before that
commit.

Fixes: a76e9bd8 (i2c: attach/detach I2C client device to the ACPI power domain)
Reported-by: NDmitry Torokhov <dtor@chromium.org>
Reviewed-by: NDmitry Torokhov <dtor@chromium.org>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

cxgb4i was returning wrong error and not releasing module reference if remote
end abruptly closed TCP connection. This prevents the cxgb4 network module from
being unloaded, further affecting other network drivers dependent on cxgb4

Sending to net as this affects all cxgb4 based network drivers.
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Aaron reported that a 32-bit x86 kernel with Physical Address Extension
(PAE) support complains about bridge prefetchable memory windows above 4GB:

  pci_bus 0000:00: root bus resource [mem 0x380000000000-0x383fffffffff]
  ...
  pci 0000:03:00.0: reg 0x10: [mem 0x383fffc00000-0x383fffdfffff 64bit pref]
  pci 0000:03:00.0: reg 0x20: [mem 0x383fffe04000-0x383fffe07fff 64bit pref]
  pci 0000:03:00.1: reg 0x10: [mem 0x383fffa00000-0x383fffbfffff 64bit pref]
  pci 0000:03:00.1: reg 0x20: [mem 0x383fffe00000-0x383fffe03fff 64bit pref]
  pci 0000:00:02.2: PCI bridge to [bus 03-04]
  pci 0000:00:02.2:   bridge window [io  0x1000-0x1fff]
  pci 0000:00:02.2:   bridge window [mem 0x91900000-0x91cfffff]
  pci 0000:00:02.2: can't handle 64-bit address space for bridge

In this kernel, unsigned long is 32 bits and dma_addr_t is 64 bits.
Previously we used "unsigned long" to hold the bridge window address.  But
this is a bus address, so we should use dma_addr_t instead.

Use dma_addr_t to hold the bridge window base and limit.

The question of whether the CPU can actually *address* the window is
separate and depends on what the physical address space of the CPU is and
whether the host bridge does any address translation.

[bhelgaas: fix "shift count > width of type", changelog, stable tag]
Fixes: d56dbf5b ("PCI: Allocate 64-bit BARs above 4G when possible")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=88131Reported-by: NAaron Ma <mapengyu@gmail.com>
Tested-by: NAaron Ma <mapengyu@gmail.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org	# v3.14+

This is currently missing, which results in a crash when one attempts
to set VXLAN tunnel over the mlx4_en when acting as PF.

	[ 2408.785472] BUG: unable to handle kernel NULL pointer dereference at (null)
	[...]
	[ 2408.994104] Call Trace:
	[ 2408.996584]  [<ffffffffa021f7f5>] ? vxlan_get_rx_port+0xd6/0x103 [vxlan]
	[ 2409.003316]  [<ffffffffa021f71f>] ? vxlan_lowerdev_event+0xf2/0xf2 [vxlan]
	[ 2409.010225]  [<ffffffffa0630358>] mlx4_en_start_port+0x862/0x96a [mlx4_en]
	[ 2409.017132]  [<ffffffffa063070f>] mlx4_en_open+0x17f/0x1b8 [mlx4_en]

While here, make sure to invoke vxlan_get_rx_port() only when VXLAN
offloads are actually enabled and not when they are only supported.
Reported-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 6fde8f03 ("bonding: fix locking in
bond_loadbalance_arp_mon()") we can have a stale bond carrier state and
stale curr_active_slave when using arp monitoring in loadbalance modes. The
reason is that in bond_loadbalance_arp_mon() we can't have
do_failover == true but slave_state_changed == false, whenever do_failover
is true then slave_state_changed is also true. Then the following piece
from bond_loadbalance_arp_mon():
                if (slave_state_changed) {
                        bond_slave_state_change(bond);
                        if (BOND_MODE(bond) == BOND_MODE_XOR)
                                bond_update_slave_arr(bond, NULL);
                } else if (do_failover) {
                        block_netpoll_tx();
                        bond_select_active_slave(bond);
                        unblock_netpoll_tx();
                }

will execute only the first branch, always and regardless of do_failover.
Since these two events aren't related in such way, we need to decouple and
consider them separately.

For example this issue could lead to the following result:
Bonding Mode: load balancing (round-robin)
*MII Status: down*
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 100
ARP IP target/s (n.n.n.n form): 192.168.9.2

Slave Interface: ens12
*MII Status: up*
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 2
Permanent HW addr: 00:0f:53:01:42:2c
Slave queue ID: 0

Slave Interface: eth1
*MII Status: up*
Speed: Unknown
Duplex: Unknown
Link Failure Count: 70
Permanent HW addr: 52:54:00:2f:0f:8e
Slave queue ID: 0

Since some interfaces are up, then the status of the bond should also be
up, but it will never change unless something invokes bond_set_carrier()
(i.e. enslave, bond_select_active_slave etc). Now, if I force the
calling of bond_select_active_slave via for example changing
primary_reselect (it can change in any mode), then the MII status goes to
"up" because it calls bond_select_active_slave() which should've been done
from bond_loadbalance_arp_mon() itself.

CC: Veaceslav Falico <vfalico@gmail.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>

Fixes: 6fde8f03 ("bonding: fix locking in bond_loadbalance_arp_mon()")
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NVeaceslav Falico <vfalico@gmail.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The removal path for selftest data has an off by one error that causes
the code to dereference beyond the end of the nodes[] array on the first
pass through. The old code only worked by chance on a lot of platforms,
but the bug was recently exposed on aarch64.

The fix is simple. Decrement the node count before dereferencing, not
after.
Reported-by: NKevin Hilman <khilman@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+

The interrupts were activated and the handler registered before the clockevent
was registered in the probe function.

The interrupt handler, however, was making the assumption that the clockevent
device was registered.

That could cause a null pointer dereference if the timer interrupt was firing
during this narrow window.

Fix that by moving the clockevent registration before the interrupt is enabled.
Reported-by: NRoman Byshko <rbyshko@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

Suggested-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJoe Stringer <joestringer@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bosch M_CAN is CAN FD capable device. This patch implements the CAN
FD features include up to 64 bytes payload and bitrate switch function.
1) Change the Rx FIFO and Tx Buffer to 64 bytes for support CAN FD
   up to 64 bytes payload. It's backward compatible with old 8 bytes
   normal CAN frame.
2) Allocate can frame or canfd frame based on EDL bit
3) Bitrate Switch function is disabled by default and will be enabled
   according to CANFD_BRS bit in cf->flags.
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Fix a few error messages.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The spec mentions there may be a delay until the value written to INIT can be
read back due to the synchronization mechanism between the two clock domains.
But it does not indicate the exact clock cycles needed. The 5us delay is a
test value and seems ok.

Without the delay, CCCR.CCE bit may fail to be set and then the initialization
fail sometimes when do repeatly up and down.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The original code missed to set the cf->can_dlc in the RTR case, so add it.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The m_can_get_berr_counter function can sleep and it may be called in napi poll
function. Rework it to fix the following warning.

root@imx6qdlsolo:~# cangen can0 -f -L 12 -D 112233445566778899001122
[ 1846.017565] m_can 20e8000.can can0: entered error warning state
[ 1846.023551] ------------[ cut here ]------------
[ 1846.028216] WARNING: CPU: 0 PID: 560 at kernel/locking/mutex.c:867 mutex_trylock+0x218/0x23c()
[ 1846.036889] DEBUG_LOCKS_WARN_ON(in_interrupt())
[ 1846.041263] Modules linked in:
[ 1846.044594] CPU: 0 PID: 560 Comm: cangen Not tainted 3.17.0-rc4-next-20140915-00010-g032d018-dirty #477
[ 1846.054033] Backtrace:
[ 1846.056557] [<80012448>] (dump_backtrace) from [<80012728>] (show_stack+0x18/0x1c)
[ 1846.064180]  r6:809a07ec r5:809a07ec r4:00000000 r3:00000000
[ 1846.069966] [<80012710>] (show_stack) from [<806c9ee0>] (dump_stack+0x8c/0xa4)
[ 1846.077264] [<806c9e54>] (dump_stack) from [<8002aa78>] (warn_slowpath_common+0x70/0x94)
[ 1846.085403]  r6:806cd1b0 r5:00000009 r4:be1d5c20 r3:be07b0c0
[ 1846.091204] [<8002aa08>] (warn_slowpath_common) from [<8002aad4>] (warn_slowpath_fmt+0x38/0x40)
[ 1846.099951]  r8:8119106c r7:80515aa4 r6:be027000 r5:00000001 r4:809d1df4
[ 1846.106830] [<8002aaa0>] (warn_slowpath_fmt) from [<806cd1b0>] (mutex_trylock+0x218/0x23c)
[ 1846.115141]  r3:80851c88 r2:8084fb74
[ 1846.118804] [<806ccf98>] (mutex_trylock) from [<80515aa4>] (clk_prepare_lock+0x14/0xf4)
[ 1846.126859]  r8:00000040 r7:be1d5cec r6:be027000 r5:be255800 r4:be027000
[ 1846.133737] [<80515a90>] (clk_prepare_lock) from [<80517660>] (clk_prepare+0x14/0x2c)
[ 1846.141583]  r5:be255800 r4:be027000
[ 1846.145272] [<8051764c>] (clk_prepare) from [<8041ff14>] (m_can_get_berr_counter+0x20/0xd4)
[ 1846.153672]  r4:be255800 r3:be07b0c0
[ 1846.157325] [<8041fef4>] (m_can_get_berr_counter) from [<80420428>] (m_can_poll+0x310/0x8fc)
[ 1846.165809]  r7:bd4dc540 r6:00000744 r5:11300000 r4:be255800
[ 1846.171590] [<80420118>] (m_can_poll) from [<8056a468>] (net_rx_action+0xcc/0x1b4)
[ 1846.179204]  r10:00000101 r9:be255ebc r8:00000040 r7:be7c3208 r6:8097c100 r5:be7c3200
[ 1846.187192]  r4:0000012c
[ 1846.189779] [<8056a39c>] (net_rx_action) from [<8002deec>] (__do_softirq+0xfc/0x2c4)
[ 1846.197568]  r10:00000101 r9:8097c088 r8:00000003 r7:8097c080 r6:40000001 r5:8097c08c
[ 1846.205559]  r4:00000020
[ 1846.208144] [<8002ddf0>] (__do_softirq) from [<8002e194>] (do_softirq+0x7c/0x88)
[ 1846.215588]  r10:00000000 r9:bd516a60 r8:be18ce00 r7:00000000 r6:be255800 r5:8056c0ec
[ 1846.223578]  r4:60000093
[ 1846.226163] [<8002e118>] (do_softirq) from [<8002e288>] (__local_bh_enable_ip+0xe8/0x10c)
[ 1846.234386]  r4:00000200 r3:be1d4000
[ 1846.238036] [<8002e1a0>] (__local_bh_enable_ip) from [<8056c108>] (__dev_queue_xmit+0x314/0x6b0)
[ 1846.246868]  r6:be255800 r5:bd516a00 r4:00000000 r3:be07b0c0
[ 1846.252645] [<8056bdf4>] (__dev_queue_xmit) from [<8056c4b8>] (dev_queue_xmit+0x14/0x18)
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The M_CAN message RAM is usually equipped with a parity or ECC functionality.
But RAM cells suffer a hardware reset and can therefore hold arbitrary content
at startup - including parity and/or ECC bits.

To prevent the M_CAN controller detecting checksum errors when reading
potentially uninitialized TX message RAM content to transmit CAN frames the TX
message RAM has to be written with (any kind of) initial data.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:

drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'
Signed-off-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Use common can_change_mtu function.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>