Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes
needed by the core drivers into the common header (delay.h etc).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix the array bounds check when transferring an extended message from the
target.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Bring the two NCR5380_reselect() implementations into agreement.

Replace infinite loops in atari_NCR5380.c with timeouts, as per NCR5380.c.

Remove 'abort' flag in NCR5380.c as per atari_NCR5380.c -- if reselection
fails, there may be no MESSAGE IN phase so don't attempt data transfer.

During selection, don't interfere with the chip registers after a
reselection interrupt intervenes.

Clean up some trivial issues with code style, comments and printk.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

SCSI bus protocol sometimes requires monitoring two related conditions
simultaneously. Enhance NCR5380_poll_politely() for this purpose, and
put it to use in the arbitration algorithm. It will also find use in
pseudo DMA.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Because interrupt handling is crucial to the core driver(s), all wrapper
drivers need to agree on this code. This patch removes discrepancies.

NCR5380_intr() in NCR5380.c has the following pointless loop that differs
from the code in atari_NCR5380.c.

	done = 1;
	do {
		/* ... */
	} while (!done);

The 'done' flag gets cleared when a reconnected command is to be processed
from the work queue. But in NCR5380.c, the flag is also used to cause the
interrupt conditions to be re-examined. Perhaps this was because
NCR5380_reselect() was expected to cause another interrupt, or perhaps
the remaining present interrupt conditions need to be handled after the
NCR5380_reselect() call?

Actually, both possibilities are bogus, as is the loop itself. It seems
have been overlooked in the hit-and-miss removal of scsi host instance
list iteration many years ago; see history/history.git commit 491447e1fcff
("[PATCH] next NCR5380 updates") and commit 69e1a9482e57 ("[PATCH] fix up
NCR5380 private data"). See also my earlier patch, "Always retry
arbitration and selection".

The datasheet says, "IRQ can be reset simply by reading the Reset
Parity/Interrupt Register". So don't treat the chip IRQ like a
level-triggered interrupt. Of the conditions that set the IRQ flag,
some are level-triggered and some are edge-triggered, which means IRQ
itself must be edge-triggered.

Some interrupt conditions are latched and some are not. Before clearing
the chip IRQ flag, clear all state that may cause it to be raised. That
means clearing the DMA Mode and Busy Monitor bits in the Mode Register
and clearing the host ID in the Select Enable register.

Also clean up some printk's and some comments. Keep atari_NCR5380.c and
NCR5380.c in agreement.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The complex main_running/queue_main mechanism is peculiar to
atari_NCR5380.c. It isn't SMP safe and offers little value given that
the work queue already offers concurrency management. Remove this
complexity to bring atari_NCR5380.c closer to NCR5380.c.

It is not a good idea to call the information transfer state machine from
queuecommand because, according to Documentation/scsi/scsi_mid_low_api.txt
that could happen in soft irq context. Fix this.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When there is a queued command and no connected command, NCR5380_select()
is called and arbitration begins. The chip waits for BUS FREE once the
MR_ARBITRATE bit in the mode register is enabled. That means there is
no need to wait for BUS FREE after disconnecting.

There is presently no polling for BUS FREE after sending an ABORT or
other message that might lead to disconnection. It only happens after
COMMAND COMPLETE or DISCONNECT messages, which seems inconsistent.
Remove the polling for !BSY in the COMMAND COMPLETE and DISCONNECT
cases.

BTW, the comments say "avoid nasty timeouts" and perhaps BUS FREE polling
was somehow helpful back in Linux v0.99.14u, when it was introduced.
The relevant timeout is presently 1 second (for bus arbitration).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Allow target selection to fail with a timeout instead of waiting in
infinite loops. This gets rid of the unused NCR_TIMEOUT macro, it is more
defensive and has proved helpful in debugging.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use timeouts in do_abort() in atari_NCR5380.c instead of infinite loops.
Also fix the kernel-doc comment. Keep the two core driver forks in sync.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Some old drivers partially implemented support for linked commands using
a "proposed" next_link pointer in struct scsi_cmnd that never actually
existed. Remove this code.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove the DEF_SCSI_QCMD macro (already removed from atari_NCR5380.c). The
lock provided by DEF_SCSI_QCMD is only needed for queue data structures.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

According to the SCSI-2 draft revision 10L, atari_NCR5380.c is correct
when it says that the phase lines are valid up until ACK is negated
following the transmission of the last byte in MESSAGE IN phase. This is
true for all information transfer phases, from target to initiator.

Sample the phase bits in STATUS_REG so that NCR5380_transfer_pio() can
return the correct result. The return value is presently unused (perhaps
because of bugs like this) but this change at least fixes the caller's
phase variable, which is passed by reference.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The atari_NCR5380.c and NCR5380.c core drivers differ in their handling of
target disconnection. This is partly because atari_NCR5380.c had all of
the polling and sleeping removed to become entirely interrupt-driven, and
it is partly because of damage done to NCR5380.c after atari_NCR5380.c was
forked. See commit 37cd23b44929 ("Linux 2.1.105") in history/history.git.

The polling changes that were made in v2.1.105 are questionable at best:
if REQ is not already asserted when NCR5380_transfer_pio() is invoked, and
if the expected phase is DATA IN or DATA OUT, the function will schedule
main() to execute after USLEEP_SLEEP jiffies and then return. The problems
here are the expected REQ timing and the sleep interval*. Avoid this issue
by using NCR5380_poll_politely() instead of scheduling main().

The atari_NCR5380.c core driver requires the use of the chip interrupt and
always permits target disconnection. It sets the cmd->device->disconnect
flag when a device disconnects, but never tests this flag.

The NCR5380.c core driver permits disconnection only when
instance->irq != NO_IRQ. It sets the cmd->device->disconnect flag when
a device disconnects and it tests this flag in a couple of places:

1. During NCR5380_information_transfer(), following COMMAND OUT phase,
   if !cmd->device->disconnect, the initiator will take a guess as to
   whether or not the target will then choose to go to MESSAGE IN phase
   and disconnect. If the driver guesses "yes", it will schedule main()
   to execute after USLEEP_SLEEP jiffies and then return there.

   Unfortunately the driver may guess "yes" even after it has denied
   the target the disconnection privilege. When the target does not
   disconnect, the sleep can be beneficial, assuming the sleep interval
   is appropriate (mostly it is not*).

   And even if the driver guesses "yes" correctly, and the target would
   then disconnect, the driver still has to go through the MESSAGE IN
   phase in order to get to BUS FREE phase. The main loop can do nothing
   useful until BUS FREE, and sleeping just delays the phase transition.

2. If !cmd->device->disconnect and REQ is not already asserted when
   NCR5380_information_transfer() is invoked, the function polls for REQ
   for USLEEP_POLL jiffies. If REQ is not asserted, it then schedules
   main() to execute after USLEEP_SLEEP jiffies and returns.

   The idea is apparently to yeild the CPU while waiting for REQ.
   This is conditional upon !cmd->device->disconnect, but there seems
   to be no rhyme or reason for that. For example, the flag may be
   unset because disconnection privilege was denied because the driver
   has no IRQ. Or the flag may be unset because the device has never
   needed to disconnect before. Or if the flag is set, disconnection
   may have no relevance to the present bus phase.

Another deficiency of the existing algorithm is as follows. When the
driver has no IRQ, it prevents disconnection, and generally polls and
sleeps more than it would normally. Now, if the driver is going to poll
anyway, why not allow the target to disconnect? That way the driver can do
something useful with the bus instead of polling unproductively!

Avoid this pointless latency, complexity and guesswork by using
NCR5380_poll_politely() instead of scheduling main().

* For g_NCR5380, the time intervals for USLEEP_SLEEP and USLEEP_POLL are
  200 ms and 10 ms, respectively. They are 20 ms and 200 ms respectively
  for the other NCR5380 drivers. There doesn't seem to be any reason for
  this discrepancy. The timing seems to have no relation to the type of
  adapter. Bizarrely, the timing in g_NCR5380 seems to relate only to one
  particular type of target device. This patch attempts to solve the
  problem for all NCR5380 drivers and all target devices.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Follow the example of the atari_NCR5380.c core driver and adopt the
NCR5380_dma_xfer_len() hook. Implement NCR5380_dma_xfer_len() for dtc.c
and g_NCR5380.c to take care of the limitations of these cards. Keep the
default for drivers using PSEUDO_DMA.

Eliminate the unused macro LIMIT_TRANSFERSIZE.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If NCR5380_select() returns -1, it means arbitration was lost or selection
failed and should be retried. If the main loop simply terminates when there
are still commands on the issue queue, they will remain queued until they
expire.

Fix this by clearing the 'done' flag after selection failure or lost
arbitration.

The "else break" clause in NCR5380_main() that gets removed here appears
to be a vestige of a long-gone loop that iterated over host instances.
See commit 491447e1fcff ("[PATCH] next NCR5380 updates") in
history/history.git.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Linux v2.1.105 changed the algorithm for polling for the BSY signal
in NCR5380_select() and NCR5380_main().

Presently, this code has a bug. Back then, NCR5380_set_timer(hostdata, 1)
meant reschedule main() after sleeping for 10 ms. Repeated 25 times this
provided the recommended 250 ms selection time-out delay. This got broken
when HZ became configurable.

We could fix this but there's no need to reschedule the main loop. This
BSY polling presently happens when the NCR5380_main() work queue item
calls NCR5380_select(), which in turn schedules NCR5380_main(), which
calls NCR5380_select() again, and so on.

This algorithm is a deviation from the simpler one in atari_NCR5380.c.
The extra complexity and state is pointless. There's no reason to
stop selection half-way and return to to the main loop when the main
loop can do nothing useful until selection completes.

So just poll for BSY. We can sleep while polling now that we have a
suitable workqueue.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When in process context, sleep during polling if doing so won't add
significant latency. In interrupt context or if the lock is held, poll
briefly then give up. Keep both core drivers in sync.

Calibrate busy-wait iterations to allow for variation in chip register
access times between different 5380 hardware implementations.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Allocate a work queue that will permit busy waiting and sleeping. This
means NCR5380_init() can potentially fail, so add this error path.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

NCR5380.c is not compliant with the SCSI-2 standard (at least, not with
the draft revision 10L that I have to refer to). The selection algorithm
in atari_NCR5380.c is correct, so use that.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If a target disappears from the SCSI bus, NCR5380_select() may
subsequently fail with a time-out. In this situation, scsi_done is
called and NCR5380_select() returns 0. Both hostdata->connected and
hostdata->selecting are NULL and the main loop should proceed with
the next command in the issue queue. Clarify this logic.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove the restart_select and targets_present variables introduced in
Linux v1.1.38. The former was used only for a questionable debug printk
and the latter "so we can call a select failure a retryable condition".
Well, retrying select failure in general is a different problem to a
target that doesn't assert BSY. We need to handle these two cases
differently; the latter case can be left to the SCSI ML.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The "failed" label in NCR5380_select() is not helpful. Some failures
return 0, others -1. Use return instead of goto to improve clarity and
brevity, like atari_NCR5380.c does. Fix the relevant comments.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove the duplicate write to the Select Enable Register that appeared
in v1.1.38.

Also remove the redundant write to Initiator Command Register prior to
calling do_abort().
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The aborted flag was introduced in v1.1.38 but never used. Remove it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Make use of do_reset() in the bus reset handler in atari_NCR5380.c. The
version in NCR5380.c already does so. Keep them in sync.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The atari_NCR5380.c core driver now takes care of bus reset upon driver
initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM
support into the core driver, enabled with a host flag, so that all
NCR5380 drivers can make use of it.

Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and
ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant.

Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and
sun3_scsi_reset_boot() routines. None of this duplicated code is needed
now that all drivers can use NCR5380_maybe_reset_bus().

This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the
other NCR5380 drivers.

The bus reset may raise an interrupt. That would be new behaviour for
atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt
is not assigned to atari_scsi at this stage, so
CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already.
Regardless, do_reset() now raises and clears the interrupt within
local_irq_save/restore which should avoid problems.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Merge the bus reset code from NCR5380.c into atari_NCR5380.c. This allows
for removal of a lot of duplicated code conditional on the RESET_BOOT
macro (in the next patch).

The atari_NCR5380.c fork lacks the do_reset() and NCR5380_poll_politely()
routines from NCR5380.c, so introduce them. They are indispensible. Keep
the two implementations in sync.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instances of var * HZ / 1000 are replaced by msecs_to_jiffies(var).
In addition some timing constants that assumed HZ 100 were adjusted
to HZ independent settings based on review comments from Michael Schmitz
<schmitzmic@gmail.com> and review of the original drivers in 1.0.31 and
2.2.16.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Acked-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Using seq_putc to print a single character saves at least a strlen()
call and a memory access, and may also give a small .text reduction.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Using seq_printf to print a simple string is a lot more expensive than
it needs to be, since seq_puts exists. Replace seq_printf with
seq_puts when possible.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There's no need to run the cmd->done callback for aborted commands. Remove
the old EH code and the RESET_RUN_DONE macro.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Unlike NCR5380.c, the atari_NCR5380.c core driver is limited to a single
instance because co-routine state is stored globally.

Fix this by removing the static scsi host pointer. For the co-routine,
obtain this pointer from the work_struct pointer instead. For the interrupt
handler, obtain it from the dev_id argument.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The atari_NCR5380.c core driver keeps some per-host data in a static
variable which limits the driver to a single instance. Fix this by moving
TagAlloc to the hostdata struct.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The static variable setup_use_tagged_queuing is declared in mac_scsi.c,
sun3_scsi.c and atari_scsi.c and doesn't belong in the core driver.
None of the other NCR5380 drivers suffer from this layering issue which
makes merging the core drivers more difficult and will likely hinder plans
for future use of platform data to configure the driver.

Replace the static variable with a host flag. This way it can be reported
along with the other flags.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The NCR5380.c core driver has moved on since the atari_NCR5380.c fork.
Some of those changes are also relevant to atari_NCR5380.c so apply them
there as well.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There is very little difference between the sun3_NCR5380.c core driver
and atari_NCR5380.c. The former is a fork of the latter.

Merge the sun3_NCR5380.c core driver into atari_NCR5380.c so that
sun3_scsi.c can adopt the latter and the former can be deleted.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Simplify falcon_release_lock_if_possible() by making callers responsible for
disabling local IRQ's, which they must do anyway to correctly synchronize
the ST DMA "lock" with core driver data structures. Move this
synchronization logic to the core driver with which it is tightly coupled.

Other LLD's like sun3_scsi and mac_scsi that can make use of this core
driver can just stub out the NCR5380_acquire_dma_irq() and
NCR5380_release_dma_irq() calls so the compiler will eliminate the
ST DMA code.

Remove a redundant local_irq_save/restore pair (irq's are disabled for
interrupt handlers these days). Revise the locking for
atari_scsi_bus_reset(): use local_irq_save/restore() instead of
atari_turnoff/turnon_irq(). There is no guarantee that atari_scsi still
holds the ST DMA lock during EH, so atari_turnoff/turnon_irq() could
end up dropping an IDE or floppy interrupt.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Make the atari_NCR5380.c core driver usable by sun3_scsi, mac_scsi and
others by moving some of the Falcon-specific code out of the core driver:
!IS_A_TT, atari_read_overruns and falcon_dont_release. Replace these with
hostdata variables and flags. FLAG_CHECK_LAST_BYTE_SENT is unused in
atari_NCR5380.c so don't set it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

atari_NCR5380.c enables its IRQ when it is already enabled. Sun3 doesn't
use the ENABLE_IRQ/DISABLE_IRQ cruft. Remove it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>