rx_params are getting updated two times in driver, which is not required.
Hence, removing duplicate updation of rx_params from rsi_prepare_skb().
Signed-off-by: NAmol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently, RSI_NEEDED_HEADROOM is '80' for rsi driver, which is wrong.
As per rsi internal frame format, the RSI_NEEDED_HEADROOM shall be '84',
which is 64(dword_align) + 4(extended_desc) + 16(frame_desc).
Hence, corrected the needed headroom.
Signed-off-by: NAmol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Removing redundant device id's from both usb and sdio idtables, as rsi
driver currently supporting only one module(RS9113). Also, replaced ids
with specific defines.
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Due to multiple calls of add interface routine, vif is getting duplicated
and at certain instance, we are out of vifs, causing the driver to behave
abnormal.

Fix: Every vif has a unique mac-id, when we got a vif with same mac-id as
the previous id's, we will override the respective vif.
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NSushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

System is unable to wake-up through magic-packet in secured connections.
Because key descriptor is getting corrupted and firmware is unable to
decrypt the magic packet. Fixed the issue by properly preparing it
before sending it to firmware.
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NSushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Radio capabilities packet is not prepared properly for 40MHZ case,
ppe_ack_rate is a two byte variable which is initialized wrongly,
hence we are unable to connect, resolved by assigning it properly.
Signed-off-by: NGanapathi Raju <ganapathi.kondraju@redpinesignals.com>
Signed-off-by: NSushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

observed low throughput rates during verification. This is because, QoS
enable flag is overridden by sequence number in the data descriptor frame.
Hence, added the fix for same.
Signed-off-by: NSiva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: NSushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Mwifiex firmware inserts only Microsoft information element
Allow other vendor specific IEs to pass from userspace
Signed-off-by: NRoman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Driver is using boolean variables to maintain vairous status
information of adapter. These status variables are accessed by
multiple threads and there is a possibility of a race. To avoid
this, convert these variables to a set of bitops flags, to be
operated atomically.

Below variables of mwifiex_adapter are converted to bitop flags:
surprise_removed
is_cmd_timedout
is_suspended
is_hs_configured
hs_enabling
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Driver must ensure that whenever it holds a pointer to the list
entry mwifiex_rx_reorder_tbl, it must protect the same with
rx_reorder_tbl_lock. At present there are many places where
driver does not ensure this. To cover all cases, spinlocks in
below funcions are moved out and made sure that the caller will
hold the spinlock:
mwifiex_11n_dispatch_pkt_until_start_win()
mwifiex_11n_scan_and_dispatch()
mwifiex_del_rx_reorder_entry()
mwifiex_11n_get_rx_reorder_tbl()
mwifiex_11n_find_last_seq_num()
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

At present driver spinlock protects iteration of list
rx_reorder_tbl_ptr with rx_reorder_tbl_lock. To protect the
individual items in this list, it uses rx_pkt_lock. But, we can
use a single rx_reorder_tbl_lock for both purposes. This patch
replaces rx_pkt_lock by rx_reorder_tbl_lock.
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use 11M as tx rate for CCK protection control frames

Fixes: 7bc04215 ("mt76: add driver code for MT76x2e")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Introduce mac80211 rts threshold handler in order to add frame
protection support to mt76x2 driver
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set MFP_CAPABLE bit in hw flag capabilities exported by the driver
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fall back to software encryption for hw unsupported ciphers in order
to enable 802.11w
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: NAndrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: NSergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2018-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

First batch of iwlwifi patches for 4.19

* Implement 802.11ax D2.0;
* Changes in the base code to support the new 22560 devices;
* Support for the new 22560 device family;

The smallest rb size supported today is 4k rx buffers.
22560 devices use 2k rxb's, so allow using 2k buffers.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In 22560 devices the firmware will do all the hw configurations,
but that's not ready yet.
Update the correct registers in the driver until the FW is ready
and does it by itself.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

22560 devices RFH uses different structures, which act similar
to the legacy rxq management lists - free and used list.

The iwl_rx_transfer_desc struct is part of the free list,
and consists of pointers to the empty rb's the driver wants to
pass to the fw.

The iwl_rx_completion_desc struct is part of the used list,
and consists of pointers to the buffer the fw filled up
with new rx, both commands and data, for the host.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

22560 devices use a new tx cmd api. Update the code to use
the new api.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

22560 devices tfd queue max size is 2^16. Allow a configurable
max size in the driver for supporting different devices.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Nowadays, the tfd queue max size is 2^8, and the reserved size in the
command header sequence field for the tfd entry index is 8 bits,
allowing an injective function from the hw pointers to the tfd entry index
in the sequence field.

In 22560 devices the tfd queue max size is 2^16, meaning that
the hw pointers are 16 bit long (allowing to point to each entry
in the tfd queue). However, the reserved space in the sequence field for
the tfd entry doesn't change, and we are limited to 8 bit.
This requires cancelling the injective function from hw pointer to
tfd entry in the sequence number.

Use iwl_pcie_get_cmd_index to wrap the hw pointer's to the n_window
size, which is maximum 256 in tx queues, and so, keep the injective
function between the window wrapped hw pointers to tfd entry index in
the sequence.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In 22560 devices the ROM sendis an interrupt to the host
once the IML reading is done.
Handle this interrupt, and indicate sw error in case the
value is fail.

Additionally, the cause for sw error in 22560 devices
have been changed, so update the cause list.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In 22560 devices we can start debug using context info gen3. Configure
the fw to start collecting logs to the dram before init.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For devices which use the image loader image, the length of the frame
must be updated in the byte count in bytes, and not dwords as today.
Avoid dividing the input length by 4.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Context information structure was added to 22000 devices for
firmware self init.

In the next generation of devices the context information
changes significantly, and the original context information
is divided roughly to three data structures: context information gen3,
prph information and prph scratch.

In addition, the init flow changes so the firmware is loaded
by the IML, and so we must allocate the IML on the DRAM and
give the ROM the IML's address before kicking the firmware's
self init.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The hw now refers to two new blocks:
* rx tr tail - The Tail index on the free buffers queue TR,
which is update by the device after reading the free buffer
from the tr.
* rx cr tail - Updated by the driver when completing
processing a new completion descriptor in the cr.

Add these two new struct to the rxq, allocate and free them
when needed.

In addition, the register for rx write pointer had been changed
to HBUS_TARG_WRPTR. The way to differentiate tx from rx is the
queue number. TX range is 0-511, and RX's is 512-527.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Device 22560 have many different hw and sw features than 22000 family,
so introduce a new family of devices - 22560.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.

Additionally, support 22560 device csr flags and addresses.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for the new 22560 family of devices and, while at it,
reorganize the 22000 family so it fits better with the new one.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Our current HE devices don't support BlockAck with the large bitmap,
so can't do TX aggregation with 256 frames. Restrict to the lower HT
size.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add HE information to the radiotap data.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a module parameter to disable 802.11ax features in supported
devices.  This is useful for testing or if there are interoperability
issues with some APs.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for the HE in the iwlwifi driver conforming with
P802.11ax_D2.0.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add the FW API definitions for HE support.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

ath.git patches for 4.19. Major changes:

wcn36xx

* fix WEP in client mode

wil6210

* add support for Talyn-MB (Talyn ver 2.0) device

* add support for enhanced DMA firmware feature