We now:
 * check for a v3 controller before setting 8-bit bus width
 * offer a callback for platform code to switch to 8-bit mode, which
   allows non-v3 controllers to support it
 * rely on mmc->caps |= MMC_CAP_8_BIT_DATA; in platform code to specify
   that the board designers have indeed brought out all the pins for
   8-bit to the slot.

We were previously relying only on whether the *controller* supported
8-bit, which doesn't tell us anything about the pin configuration in
the board design.

This fixes the MMC card regression reported by Maxim Levitsky here:
   http://thread.gmane.org/gmane.linux.kernel.mmc/4336
by no longer assuming that 8-bit works by default.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Tested-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some board/card/host configurations are not capable of powering off the
card after boot.

To support such configurations, and to allow smoother transition to
runtime PM behavior, MMC_CAP_POWER_OFF_CARD is added, so hosts need to
explicitly indicate whether it's OK to power off their cards after boot.

SDIO core will enable runtime PM for a card only if that cap is set.
As a result, the card will be powered down after boot, and will only
be powered up again when a driver is loaded (and then it's up to the
driver to decide whether power will be kept or not).

This will prevent sdio_bus_probe() failures with setups that do not
support powering off the card.
Reported-and-tested-by: NDaniel Drake <dsd@laptop.org>
Reported-and-tested-by: NArnd Hannemann <arnd@arndnet.de>
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Power off the card in mmc_sdio_detect __before__ a potential error
handler, which completely removes the card, executes, and only if the
card was successfully powered on beforehand.

While we're at it, use the _sync variant of the runtime PM put API, in
order to ensure that the card is left powered off in case an error
occurred, and the card is going to be removed.

Reproduced and tested on the OLPC XO-1.5.
Reported-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

While booting OMAP4 ES2.0 boards, cards on MMC1 and MMC2 controllers
are not getting detected sometimes.

During reset of command/data line, wrong pointer to base address
was passed while read operation to SYSCTL register, thus impacting
the updated reset logic.

Passing the correct base address fixes the issue.
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC hosts that poll for card detection by defining the MMC_CAP_NEEDS_POLL
flag have a race on rmmod, where the delayed work is cancelled without
waiting for completed polling. To prevent this a _sync version of the work
cancellation has to be used.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDHC2 is newly added in C0 stepping of Langwell. Without the Moorestown
specific quirk, the default pci_probe will be called and crash the kernel.

This patch unblocks the crash problem on C0 by using the same probing
function as HC1, which limits the number of slots to one.
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Only these CPUs list the bug in their errata.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes timeout problems on i.MX's sdhci as suggested by
Richard Zhu.

Tested on:
- i.MX257: not needed
- i.MX357: needed
- i.MX515: needed

More details can be found here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-October/029748.htmlSigned-off-by: NEric Bénard <eric@eukrea.com>
Tested-by: NShawn Guo <shawn.gsc@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

A little more work was needed for SDIO IRQ wakeups to be functional.

Wake-on-WLAN on the SD WiFi adapter in the XO-1.5 laptop is now working.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Improves error handling in the ushc driver.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

We should not call mmc_card_set_ddr_mode() if we are in single data
mode.  This sets DDR and causes the kernel log to say the card is DDR
when it is not.

Explicitly set ddr to 0 rather then rely on MMC_SDR_MODE being 0 when
doing the checks.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Commit 27ae60f8 ("ipw2x00: replace "ieee80211" with "libipw" where
appropriate") changed DRV_NAME to be "libipw", but didn't properly fix
up the places where it was used to specify the name for the /proc/net/
directory.

For backwards compatibility reasons, that directory name remained
"ieee80211", but due to the DRV_NAME change, the error case printouts
and the cleanup functions now used "libipw" instead.  Which made it all
fail badly.

For example, on module unload as reported by Randy:

  WARNING: at fs/proc/generic.c:816 remove_proc_entry+0x156/0x35e()
  name 'libipw'

because it's trying to unregister a /proc directory that obviously
doesn't even exist.

Clean it all up to use DRV_PROCNAME for the actual /proc directory name.
Reported-and-tested-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: BookE: Load the lower half of MSR
  KVM: PPC: BookE: fix sleep with interrupts disabled
  KVM: PPC: e500: Call kvm_vcpu_uninit() before kvmppc_e500_tlb_uninit().
  PPC: KVM: Book E doesn't have __end_interrupts.
  KVM: x86: Issue smp_call_function_many with preemption disabled
  KVM: x86: fix information leak to userland
  KVM: PPC: fix information leak to userland
  KVM: MMU: fix rmap_remove on non present sptes
  KVM: Write protect memory after slot swap

Commit 48821184 ("floppy: switch to one queue per drive instead of
sharing a queue") introduced a use-after-free.  We do "put_disk()" on
the disk device _before_ we then clean up the queue associated with that
disk.

Move the put_disk() down to avoid dereferencing a free'd data structure.

Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Reported-and-tested-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit d9ca07a0 ("watchdog: Avoid kernel crash when disabling
watchdog") introduces a section mismatch.

Now that we reference no_watchdog from non-__init code it can no longer
be __initdata.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
  inet_diag: Make sure we actually run the same bytecode we audited.
  netlink: Make nlmsg_find_attr take a const nlmsghdr*.
  fib: fib_result_assign() should not change fib refcounts
  netfilter: ip6_tables: fix information leak to userspace
  cls_cgroup: Fix crash on module unload
  memory corruption in X.25 facilities parsing
  net dst: fix percpu_counter list corruption and poison overwritten
  rds: Remove kfreed tcp conn from list
  rds: Lost locking in loop connection freeing
  de2104x: fix panic on load
  atl1 : fix panic on load
  netxen: remove unused firmware exports
  caif: Remove noisy printout when disconnecting caif socket
  caif: SPI-driver bugfix - incorrect padding.
  caif: Bugfix for socket priority, bindtodev and dbg channel.
  smsc911x: Set Ethernet EEPROM size to supported device's size
  ipv4: netfilter: ip_tables: fix information leak to userland
  ipv4: netfilter: arp_tables: fix information leak to userland
  cxgb4vf: remove call to stop TX queues at load time.
  cxgb4: remove call to stop TX queues at load time.
  ...

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: fix race when reading count in AR descriptor
  firewire: ohci: avoid reallocation of AR buffers
  firewire: ohci: fix race in AR split packet handling
  firewire: ohci: fix buffer overflow in AR split packet handling

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: make cifs_set_oplock_level() take a cifsInodeInfo pointer
  cifs: dereferencing first then checking
  cifs: trivial comment fix: tlink_tree is now a rbtree
  [CIFS] Cleanup unused variable build warning
  cifs: convert tlink_tree to a rbtree
  cifs: store pointer to master tlink in superblock (try #2)
  cifs: trivial doc fix: note setlease implemented
  CIFS: Add cifs_set_oplock_level
  FS: cifs, remove unneeded NULL tests

posix-cpu-timers.c correctly assumes that the dying process does
posix_cpu_timers_exit_group() and removes all !CPUCLOCK_PERTHREAD
timers from signal->cpu_timers list.

But, it also assumes that timer->it.cpu.task is always the group
leader, and thus the dead ->task means the dead thread group.

This is obviously not true after de_thread() changes the leader.
After that almost every posix_cpu_timer_ method has problems.

It is not simple to fix this bug correctly. First of all, I think
that timer->it.cpu should use struct pid instead of task_struct.
Also, the locking should be reworked completely. In particular,
tasklist_lock should not be used at all. This all needs a lot of
nontrivial and hard-to-test changes.

Change __exit_signal() to do posix_cpu_timers_exit_group() when
the old leader dies during exec. This is not the fix, just the
temporary hack to hide the problem for 2.6.37 and stable. IOW,
this is obviously wrong but this is what we currently have anyway:
cpu timers do not work after mt exec.

In theory this change adds another race. The exiting leader can
detach the timers which were attached to the new leader. However,
the window between de_thread() and release_task() is small, we
can pretend that sys_timer_create() was called before de_thread().
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (ltc4261) Fix error message format
  hwmon: (ltc4261) Add missing newline in debug message

All the callers already have a pointer to struct cifsInodeInfo. Use it.
Signed-off-by: NSuresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: NPavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: NSteve French <sfrench@us.ibm.com>

adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile: mark "hardwall" device as non-seekable
  asm-generic/stat.h: support 64-bit file time_t for stat()
  arch/tile: don't allow user code to set the PL via ptrace or signal return
  arch/tile: correct double syscall restart for nested signals
  arch/tile: avoid __must_check warning on one strict_strtol check
  arch/tile: bomb raw_local_irq_ to arch_local_irq_
  arch/tile: complete migration to new kmap_atomic scheme

Add MODULE_LICENSE() that matches file comments so that kernel
is not tainted.

	leds_net5501: module license 'unspecified' taints kernel.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NRichard Purdie <rpurdie@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This was preventing the guest from setting any bits in the
hardware MSR which aren't forced on, such as MSR[SPE].
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

It is not legal to call mutex_lock() with interrupts disabled.
This will assert with debug checks enabled.

If there's a real need to disable interrupts here, it could be done
after the mutex is acquired -- but I don't see why it's needed at all.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Reviewed-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

The VCPU uninit calls some TLB functions, and the TLB uninit function
frees the memory used by them.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Fix an unresolved symbol with CONFIG_KVM_GUEST plus CONFIG_RELOCATABLE on
Book E.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

smp_call_function_many is specified to be called only with preemption
disabled. Fulfill this requirement.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Structures kvm_vcpu_events, kvm_debugregs, kvm_pit_state2 and
kvm_clock_data are copied to userland with some padding and reserved
fields unitialized.  It leads to leaking of contents of kernel stack
memory.  We have to initialize them to zero.

In patch v1 Jan Kiszka suggested to fill reserved fields with zeros
instead of memset'ting the whole struct.  It makes sense as these
fields are explicitly marked as padding.  No more fields need zeroing.

KVM-Stable-Tag.
Signed-off-by: NVasiliy Kulikov <segooon@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Structure kvm_ppc_pvinfo is copied to userland with flags and
pad fields unitialized.  It leads to leaking of contents of
kernel stack memory.
Signed-off-by: NVasiliy Kulikov <segooon@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

drop_spte should not attempt to rmap_remove a non present shadow pte.

This fixes a BUG_ON seen on kvm-autotest.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Reported-by: NLucas Meneghel Rodrigues <lmr@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

I have observed the following bug trigger:

1. userspace calls GET_DIRTY_LOG
2. kvm_mmu_slot_remove_write_access is called and makes a page ro
3. page fault happens and makes the page writeable
   fault is logged in the bitmap appropriately
4. kvm_vm_ioctl_get_dirty_log swaps slot pointers

a lot of time passes

5. guest writes into the page
6. userspace calls GET_DIRTY_LOG

At point (5), bitmap is clean and page is writeable,
thus, guest modification of memory is not logged
and GET_DIRTY_LOG returns an empty bitmap.

The rule is that all pages are either dirty in the current bitmap,
or write-protected, which is violated here.

It seems that just moving kvm_mmu_slot_remove_write_access down
to after the slot pointer swap should fix this bug.

KVM-Stable-Tag.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We can optimize kernel/relay.c::relay_alloc_page_array() slightly by
using vzalloc.  The patch makes these changes:

 - use vzalloc instead of vmalloc+memset.
 - remove redundant local variable 'array'.
 - declare local 'pa_size' as const.

Cuts down nicely on both source and object-code size.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NPekka Enberg <penberg@kernel.org>
Acked-by: NMathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k, m68knommu: Do not include linux/hardirq.h in asm/irqflags.h
  m68knommu: add back in declaration of do_IRQ

This patch is based on Dan's original patch. His original description is
below:

Smatch complained about a couple checking for NULL after dereferencing
bugs.  I'm not super familiar with the code so I did the conservative
thing and move the dereferences after the checks.

The dereferences in cifs_lock() and cifs_fsync() were added in
ba00ba64 "cifs: make various routines use the cifsFileInfo->tcon
pointer".  The dereference in find_writable_file() was added in
6508d904 "cifs: have find_readable/writable_file filter by fsuid".
The comments there say it's possible to trigger the NULL dereference
under stress.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NSteve French <sfrench@us.ibm.com>

Noticed while reviewing (late) the rbtree conversion patchset (which has been merged
already).

Cc: Jeff Layton <jlayton@redhat.com>
Signed-off-by: NSuresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: NSteve French <sfrench@us.ibm.com>

We were using nlmsg_find_attr() to look up the bytecode by attribute when
auditing, but then just using the first attribute when actually running
bytecode. So, if we received a message with two attribute elements, where only
the second had type INET_DIAG_REQ_BYTECODE, we would validate and run different
bytecode strings.

Fix this by consistently using nlmsg_find_attr everywhere.
Signed-off-by: NNelson Elhage <nelhage@ksplice.com>
Signed-off-by: NThomas Graf <tgraf@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will let us use it on a nlmsghdr stored inside a netlink_callback.
Signed-off-by: NNelson Elhage <nelhage@ksplice.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>