This patch adds SD8887 support to mwifiex.
SD8887 is Marvell's 1x1 11ac solution.

The corresponding firmware image file is located at:
"mrvl/sd8887_uapsta.bin"
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds some more defitions to card specific register structure
and removes static defines for these registers.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When mwifiex device becomes GO, unicast traffic between client1 and GO stops
when client2 connects to GO. Reason behind this was PTK getting
overwritten by key_material command for client2 as it did not have client
mac address. So, client1 can no more decode GO's ping packets though it
responds to its broadcast packets.

This patch adds case to check for BSS_ROLE instead of bss_type to set
client mac address while configuring keys when device becomes GO.
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SKB lists have their own lock. So this lock is not needed.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes an issue with rx processing function where we were
decrementing rx_pending count twice.

Patch also queues correct main_work item when rx_pending count reaches
low watermark.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A soft lockup was observed on ARM multicore platform while UDP
RX iperf was running on station.

Reason for this is delay_main_task was not taken into consideration while
jumping to process_start. Now if delay_main_task is true, we would exit
mwifiex_main_process instead of going to process_start again.
This ensure other process is scheduled on this CPU and soft lockup is avoided.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKevin Gan <ganhy@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We will now dump MAC, APU, CIU, ICU firmware memory segments also
for PCIe interface. Following is the updated userspace script which
reads firmware dump information.

    mwifiex_pcie_fw_dump.sh: #!/bin/bash
    ethtool --set-dump mlan0 0
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/ITCM.log

    ethtool --set-dump mlan0 1
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/DTCM.log

    ethtool --set-dump mlan0 2
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/SQRAM.log

    ethtool --set-dump mlan0 3
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/IRAM.log

    ethtool --set-dump mlan0 4
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/APU.log

    ethtool --set-dump mlan0 5
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/CIU.log

    ethtool --set-dump mlan0 6
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/ICU.log

    ethtool --set-dump mlan0 7
    ethtool --get-dump mlan0
    ethtool --get-dump mlan0 data /tmp/MAC.log
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch takes care of missing error paths in firmware dump.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check for scan channel gap only when user_scan_in is not NULL.
user_scan_in is NULL for internal scans and if we check scan channel gap
at this place, it may result into crash.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch sets uAP BA window sizes to 64.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds RX work queue support to mwifiex.
Packets received are queued to internal queue which are then
processed by scheduling a work item for RX process.

RX work is enabled only on SMP systems.
Reviewed-by: NJames Cameron <quozl@laptop.org>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have a logic in driver to delay or abort low priority scan
to serve Tx traffic effectively. With scan channel
gap support added, firmware now allows driver to send Tx data while
scan operation is in progress. Hence low priority scan handling
in driver is not required now. This patch removes related code.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This variable is never used, get rid of it.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With channel scan gap, FW comes back to connected channel after each
single channel scan. So we can safely transfer data to FW during scan.
FW would send this data once on connected channel.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With scan channel gap in place, FW comes back to connected channel
after each scan; so we dont need to restrict FW to scan
single channel while connected.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With scan channel gap when any station/AP is active, FW comes back
to connected channel for any pending data transfter after scanning each
channel.
We set scan channel gap TLV to FW in scan command when any of the
interface is active. This enables scan channel gap in FW.
Also when scan channel gap is enabled, we would scan maximum channels
allowed by FW.

Scan channel gap is supported only on FW with V15 FW API.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was observed that station would sent probe request even when
scan type has been set as passive during iw scan.
This was happening because driver sets passive scan type only
when channel has IEEE80211_CHAN_NO_IR flag set.
Along with this, add condition to check if no ssids are specified in
scan request so as to mark such scan request passive.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'mp_data_port_mask' and 'mp_end_port' gives correct information
even for the chipsets supporting SDIO new mode (32 ports).
We will get rid of this chip specific handling.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When aggregation port limit is reached, we stop aggregation and
the data is sent to firmware. It is observed that one less packet
than the port limit is aggregated in this case. ex. 15 instead of
16.
The reason is we have redundant port limit checks before current
packet is added to aggregation buffer.

The issue is fixed by removing these checks. We already have
necessary check in precopy current buffer handling.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When assocaiting to an AP , mwifiex set supported data rates
based on target AP's capability. For 5G AP(11a mode), a/n/ac mode
would possibly be set.
However, for some chips which dont support 11AC mode current config_bands
will be used instead.

For example, if we join an IBSS in 11b mode ,adapter->config_bands
will be set to 1(11b mode). Then we leave IBSS ,and try to connect
5G a/n mode AP. At this time , only 11b mode data rates will be
supported in assoc request , which result in assoc failure with
reason code 18: Association denied due to requesting station not
supporting all rates.

This patch fix such a cornel case, by adding additional check for
current chip's 11ac capability.
Reported-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for writing CPU event interrupt done back
to device.
Patch also increases interrupt buffer ring size from 4 to 8.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was an issue with internal scan during association wherein
we would complete internal scan on first scan command response.
This would cause association failure if AP is not found in first scan
response e.g. APs from A band.
This patch fixes this issue by completing internal scan only when all
scan commands from scan pending queue and command pending queue are
sent to FW and response to last scan command is received.
Tested-by: NXinmin Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If rx_len received in interface header from FW is more than
RX buffer size, skb_put for such length results into skb_panic.
Avoid this by not processing such packets. We just print a warning
for such packets and free skb.
Reviewed-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Size of RSN IE buffer in driver is 254 while maximum size of received buffer
to be copied to RSN IE buffer can be 255. Add boundary check to copy maximum
of 254 bytes into RSN IE buffer.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we dont set FW API info here, for older FW releases where FW API
is not available in GET_HW_SPEC, API version would remain 0.
This may cause issues with 11ac if older FW is used with newer driver.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the much more common pr_warn instead of pr_warning.

Other miscellanea:

o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer firmware returns API revision in GET_HW_SPEC command
response. We will make use of it instead of parsing this
information from FW release number.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We will remove 'fw' prefix from these variable and macro
names and make them generic.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While updating 'left_len' in each iteration, we should subtract
last TLV length not the accumulated length of TLVs parsed till
now.
This bug in parsing logic is exposed by newer firmware which adds
two TLVs in GET_HW_SPEC command response. Earlier firmwares used to
add only one TLV.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).

For good measure, use it in ath6kl.

Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.

Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.

Found by using regex suggested by Joe Perches.
Signed-off-by: NHans Wennborg <hans@hanshq.net>
Acked-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

mmc_rescan will scan for non-removable cards only once, hence the card
will not be rediscovered.
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need wall-clock time here, and in most configurations
that care, there are already timestamps in the kernel using
CONFIG_PRINTK_TIME=y.
Reported-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In managed mode if the driver is getting a re-associate command
from cfg80211, driver deauthenticates with the AP internally and
sends a disconnected event to cfg80211 before completion of its
association process. The disconnected event then modifies the
SSID length as wdev->ssid_len = 0. So, upon receiving the connect
result event from driver, cfg80211 is unable to get that BSS from
the device's BSS list and generates the following WARN_ON message.

WARNING: CPU: 0 PID: 857 at net/wireless/sme.c:658
         __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]()

Avoid re-association while the device is already associated to a
network. Also remove the internal deauthentication from the
association path.
Signed-off-by: NUjjal Roy <royujjal@gmail.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This local variable is not used anywhere in function.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The unwanted frame types are already handled in 'default' case
of the switch/case below.
The str_ptr is allocated but it can be leaked if the length check
fails in the REQUEST/RESP cases. Fix it by allocating sta_ptr
after the length checks.
Reported-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert
all users to pass NET_NAME_UNKNOWN.

Coccinelle patch:

@@
expression sizeof_priv, name, setup, txqs, rxqs, count;
@@

(
-alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs)
+alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs)
|
-alloc_netdev_mq(sizeof_priv, name, setup, count)
+alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count)
|
-alloc_netdev(sizeof_priv, name, setup)
+alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup)
)

v9: move comments here from the wrong commit
Signed-off-by: NTom Gundersen <teg@jklm.no>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes this typo.
Reported-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>