It's been observed that sometimes link credit restore takes
a lot of time than the current timeout. This patch increases
the default timeout value and return the proper error value
on failure.

Fixes: 1c74b891 ("octeontx2-af: Wait for TX link idle for credits change")
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CN10K platforms uses RPM(0..2)_MTI_MAC100(0..3)_COMMAND_CONFIG
register for lmac TX/RX enable whereas CN9xxx platforms use
CGX_CMRX_CONFIG register. This config change was missed when
adding support for CN10K RPM.

Fixes: 91c6945e ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rvu_nix_get_bpid() lbk_bpid_cnt is being read from
wrong register. Due to this backpressure enable is failing
for LBK VF32 onwards. This patch fixes that.

Fixes: fe1939bb ("octeontx2-af: Add SDP interface support")
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes possible null pointer dereference in files
"rvu_debugfs.c" and "rvu_nix.c"

Fixes: 8756828a ("octeontx2-af: Add NPA aura and pool contexts to debugfs")
Fixes: 9a946def ("octeontx2-af: Modify nix_vtag_cfg mailbox to support TX VTAG entries")
Signed-off-by: NRakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support to flush or invalidate CPT CTX entries as part of FLR
and also provides a mailbox to flush CPT CTX entries in case of
graceful exit.
This patch also adds support for AF -> CPT PF uplink mailbox messages
and adds a new mbox message to submit a CPT instruction from AF.
Signed-off-by: NSrujana Challa <schalla@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.

Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon receiving ptp config request from netdev interface , Octeontx2 MAC
block CGX is configured to append timestamp to every incoming packet
and NPC config is updated with DMAC offset change.

Currently this configuration is not reset in FLR handler. This patch
resets the same.
Signed-off-by: NHarman Kalra <hkalra@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimized KPU1 entry processing for variable-length custom L2 headers
of size 24B, 90B by
	- Moving LA LTYPE parsing for 24B and 90B headers to PKIND.
	- Removing LA flags assignment for 24B and 90B headers.
	- Reserving a PKIND 55 to parse variable length headers.

Also, new mailbox(NPC_SET_PKIND) added to configure PKIND with
corresponding variable-length offset, mask, and shift count
(NPC_AF_KPUX_ENTRYX_ACTION0).
Signed-off-by: NKiran Kumar K <kirankumark@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per HW errata AQ modification to CQ could be discarded on heavy
traffic. This patch implements workaround for the same after each
CQ write by AQ check whether the requested fields (except those
which HW can update eg: avg_level) are properly updated or not.

If CQ context is not updated then perform AQ write again.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case where the condition !is_rvu_otx2(rvu) is false variable
val is not initialized and can contain a garbage value. Fix this by
initializing val to zero and bit-wise or'ing in BIT_ULL(51) to val
for the true condition case of !is_rvu_otx2(rvu).

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 4b5a3ab1 ("octeontx2-af: Hardware configuration for inline IPsec")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On OcteonTX2/CN10K SoC, the admin function (AF) is the only one
with all priviliges to configure HW and alloc resources, PFs and
it's VFs have to request AF via mailbox for all their needs.
This patch adds new mailbox messages for CPT PFs and VFs to configure
HW resources for inline-IPsec.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSrujana Challa <schalla@marvell.com>
Signed-off-by: NVidya Sagar Velumuri <vvelumuri@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For better performance set hardware to use NDC TX for reading packet
data specified NIX_SEND_SG_S.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added mbox for PF/VF drivers to retrieve current ingress bandwidth
profile free count. Also added current policer timeunit
configuration info based on which ratelimiting decisions can be
taken by PF/VF drivers.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for packet IO via SDK links which is used when
Octeon is connected as a end-point. Traffic host to end-point
and vice versa flow through SDP links. This patch also support
dual SDP blocks supported in 98xx silicon.
Signed-off-by: NRadha Mohan Chintakuntla <radhac@marvell.com>
Signed-off-by: NNalla Pradeep <pnalla@marvell.com>
Signed-off-by: NSubrahmanyam Nilla <snilla@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 98xx, there are 2 NIX blocks and 4 LBK blocks present. The way
these NIX-LBK should be configured depends on the use case. By
default loopback functionality is supported in AF VF pairs which
are attached to NIX0 and NIX1 LFs alternatively to ensure load
balancing. NIX0 transmits a packet to LBK1 which will be received
by NIX1 and packet transmitted by NIX1 will get received by NIX0 via
LBK2.

There are some requirements where only one AF VF is used and respective
NIX is expected to operate in a mode where it can receive it own packet
back. This can be achieved if NIX0 sends packet to LBK0 and not LBK1.
Adding a flag in LF alloc request mailbox which can setup NIX0 to use
LBK0 and NIX1 can use LBK3.
Signed-off-by: NHarman Kalra <hkalra@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike OcteonTx2, the channel numbers used by CGX/RPM
and LBK on CN10K silicons aren't fixed in HW. They are
SW programmable, hence we cannot derive transmit link
from static channel numbers anymore. Get the same from
admin function via mailbox.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before C0 HW revision, The RSS adder was computed based the
following static formula.

rss_adder<7:0> = flow_tag<7:0> ^ flow_tag<15:8> ^
flow_tag<23:16> ^ flow_tag<31:24>

The above scheme has the following drawbacks:
1) It is not in line with other standard NIC behavior.
2) There can be an SW use case where SW can compute the hash
upfront using Toeplitz function and predict the queue selection
to optimize some packet lookup function. The nonstandard
way of doing XOR makes the consumer to not predict the queue selection.

C0 HW revision onwards, The HW can configure the
rss_adder<7:0> as flow_tag<7:0> to align with standard NICs.

This patch adds an option to select legacy RSS adder mode
vs standard NIC behavior by setting NIX_LF_RSS_TAG_LSB_AS_ADDER flag.

Since this bit field is used as reserved in old HW revisions,
No need to have an additional HW version check.
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting from 96xx C0 onwards all silicons support traffic shaping.
This patch enables that feature along with other changes
- When PIR/CIR shaping config is modified, toggle SW_XOFF
  for config to take effect
- Before SMQ flush, clear SW_XOFF at all parent schedulers
- Support to read current transmit scheduler configuration via mbox
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIX_AF_TX_LINKX_NORM_CREDIT holds running counter of
tx credits available per link. But, tx credits should be
configured based on MTU config. So MTU change needs tx
credit count update.

An issue exists whereby when both PF & VF are enabled and
PF traffic is flowing, if VF requests for MTU update,
updating the NORM_CREDIT register will lead to corruption
of credit count and subsequent deadlock of tx link as
the NORM_CREDIT register holds running count.

This patch provides workaround by pausing link traffic
using NIX_AF_TL1X_SW_XOFF, waiting for existing packets to
drain, and used credits be returned before updating new
credit count.
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bandwidth profiles (ipolicer structure)is implemented only on CN10K
platform. But current code try to free the ipolicer memory without
checking the capibility flag leading to driver crash on OCTEONTX2
platform. This patch fixes the issue by add capability flag check.

Fixes: e8e095b3 ("octeontx2-af: cn10k: Bandwidth profiles config support")
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add appropriate error codes to be used when returning from AF
mailbox handlers due to some error condition.
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Program SQ, MDQ, TL4 to TL2 transmit scheduler queues' DWRR
weight based on DWRR MTU programmed at NIX_AF_DWRR_RPM_MTU.
The DWRR MTU from admin function is retrieved via mbox.

On OcteaonTx2 silicon, admin function driver responds with DWRR
MTU as '1'. This helps to avoid silicon specific transmit
scheduler DWRR quantum/weight configuration logic.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On OcteonTx2 DWRR quantum is directly configured into each of
the transmit scheduler queues. And PF/VF drivers were free to
config any value upto 2^24.

On CN10K, HW is modified, the quantum configuration at scheduler
queues is in terms of weight. And SW needs to setup a base DWRR MTU
at NIX_AF_DWRR_RPM_MTU / NIX_AF_DWRR_SDP_MTU. HW will do
'DWRR MTU * weight' to get the quantum. For LBK traffic, value
programmed into NIX_AF_DWRR_RPM_MTU register is considered as
DWRR MTU.

This patch programs a default DWRR MTU of 8192 into HW and also
provides a way to change this via devlink params.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIX_RX_SW_SYNC ensures all existing transactions are finished and
pkts are written to LLC/DRAM, queues should be teared down after
successful SW_SYNC. Due to a HW errata, in some rare scenarios
an existing transaction might end after SW_SYNC operation. To
ensure operation is fully done, do the SW_SYNC twice.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently PKINDs are not assigned to LBK channels.
The default value of LBK_CHX_PKIND (channel to PKIND mapping) register
is zero, which is resulting in a overlap of pkind between LBK and CGX
LMACs. When KPU1 parser config is modified when PTP timestamping is
enabled on the CGX LMAC interface it is impacting traffic on LBK
interfaces as well.

This patch fixes the issue by reserving the PKIND#0 for LBK devices.
CGX mapped PF pkind starts from 1 and also fixes the max pkind available.

Fixes: 42157217 ("octeontx2-af: Support to enable/disable HW timestamping")
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove devm_kfree of memory where VLAN entry to RVU PF mapping
info is saved. This will be freed anyway at driver exit.
Having this could result in warning from devm_kfree() if
the memory is not allocated due to errors in rvu_nix_block_init()
before nix_setup_txvlan().

Fixes: 9a946def ("octeontx2-af: Modify nix_vtag_cfg mailbox to support TX VTAG entries")
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of now any communication between CGXs PFs and
their VFs within the system is possible only by
external switches sending packets back to the
system. This patch adds internal switching support.
Broadcast packet replication is not covered here.
RVU admin function (AF) maintains MAC addresses
of all interfaces in the system. When switching is
enabled, MCAM entries are allocated to install rules
such that packets with DMAC matching any of the
internal interface MAC addresses is punted back
into the system via the loopback channel.
On the receive side the default unicast rules
are modified to not check for ingress channel.
So any packet with matching DMAC irrespective of
which interface it is coming from will be forwarded
to the respective PF/VF interface.
The transmit side rules and default unicast rules
are updated if user changes MAC address of an interface.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For enabling VF-VF switching the packets egressing
out of CGX mapped VFs needed to be sent to LBK
so that same packets are received back to the system.
But the LBK link also needs to be enabled in addition
to a VF's mapped CGX_LMAC link otherwise hardware
raises send error interrupt indicating selected LBK
link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register.
Hence this patch enables all LBK links in
TL3_TL2_LINKX_CFG registers.
Also to enable packet flow between PFs/VFs of NIX0
to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC
rules has to be installed such that rules must be hit
for any TX interface i.e., NIX0-TX or NIX1-TX provided
DMAC match creteria is met. Hence this patch changes the
behavior such that MCAM is programmed to match with any
NIX0/1-TX interface for TX rules.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAC block supports 32 dmac filters which are logically
divided among all attached LMACS.

For example MAC block0 having one LMAC then maximum supported
filters are 32 where as MAC block1 having 4 enabled LMACS
them maximum supported filteres are 8 for each LMAC.

This patch adds mbox handlers to add/delete/update mac entry
in DMAC filter table.
Signed-off-by: NSunil Kumar Kori <skori@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for dumping current resource status of bandwidth
profiles and contexts of allocated profiles via debugfs.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CN10K silicons supports hierarchial ingress packet ratelimiting.
There are 3 levels of profilers supported leaf, mid and top.
Ratelimiting is done after packet forwarding decision is taken
and a NIXLF's RQ is identified to DMA the packet. RQ's context
points to a leaf bandwidth profile which can be configured
to achieve desired ratelimit.

This patch adds logic for management of these bandwidth profiles
ie profile alloc, free, context update etc.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new mailbox to enable PF to configure VF as trusted VF.
Trusted VF feature allows VFs to perform priviliged operations
such as enabling VF promiscuous mode, all-multicast mode and
changing the VF MAC address configured by PF. Refactored the
VF interface flags maintained by the AF driver such that the
flags do not overlap for various configurations.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, multicast packet filtering is accomplished by installing
MCAM rule that matches all-multicast MAC address and has its
NPC_RX_ACTION set to unicast to PF. Similarly promisc feature is
achieved by installing MCAM rule that matches all the traffic received
by the channel and unicast the packets to PF. This approach only applies
to PF and is not scalable across VFs.

This patch adds support for PF/VF multicast and promisc feature by
reserving NIX_RX_MCE_S entries from the global MCE list allocated
during NIX block initialization. The NIX_RX_MCE_S entries create a
linked list with a flag indicating the end of the list, and each entry
points to a PF_FUNC (either PF or VF). When a packet NPC_RX_ACTION is
set to MCAST, the corresponding NIX_RX_MCE_S list is traversed and the
packet is queued to each PF_FUNC available on the list.

The PF or VF driver adds the multicast/promisc packet match entry and
updates the MCE list with correspondng PF_FUNC. When a PF or VF interface
is disabled, the corresponding NIX_RX_MCE_S entry is removed from the
MCE list and the MCAM entry will be disabled if the list is empty.
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CN10k introduces following new LT DEF registers:
1. APAD (alignment padding) LT DEF registers are
enhancement to existing apad calculation algorithm
where not just ipv4 and ipv6 but also other protocols
can be matched and required alignment can be added by NIX.

2. ET LT DEF register defines layer information in NPC_RESULT_S
to identify the Ethertype location in L2 header. Used for
Ethertype overwriting in inline IPsec flow.

This patch adds required structures and some header changes. Also
strict version check (based on minor field) is imposed to highlight
version mismatch between the kernel headers and KPU profile.
Signed-off-by: NHarman Kalra <hkalra@marvell.com>
Signed-off-by: NJerin Jacob Kollanukkaran <jerinj@marvell.com>
Signed-off-by: NKiran Kumar Kokkilagadda <kirankumark@marvell.com>
Signed-off-by: NGeorge Cherian <george.cherian@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Initialize l4_key_offset variable to fix uninitialized
variable compiler warning.

Fixes: b9b7421a ("octeontx2-af: Support ESP/AH RSS hashing")
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A mcam rule described by mcam_rule struct has all the info
such as the hardware MCAM entry number, match criteria and
corresponding action etc. All mcam rules are stored in a
linked list mcam->rules. When adding/updating a rule to the
mcam->rules it is checked if a rule already exists for the
mcam entry. If the rule already exists, the same rule is
updated instead of creating new rule. This way only one
mcam_rule exists for the only one default unicast entry
installed by AF. But a PF/VF can get different NIXLF
(or default unicast entry number) after a attach-detach-attach
sequence. When that happens mcam_rules list end up with two
default unicast rules. Fix the problem by deleting the default
unicast rule list node always when disabling mcam rules.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for multi channel NIX promisc entry. Packets sent
on all those channels by the host should be received by the interface to
which those channels belong. Channel count, if greater than 1, should be
power of 2 as only one promisc entry is available for the interface. Key
mask is modified such that incoming packets from channel base to channel
count are directed to the same pci function.
Signed-off-by: NNalla, Pradeep <pnalla@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow control configuration is different for CGX(Octeontx2)
and RPM(CN10K) functional blocks. This patch adds the necessary
changes for RPM to support 802.3 pause frames configuration on
cn10k platforms.
Signed-off-by: NRakesh Babu <rsaladi2@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OcteonTx3 CN10K silicon supports bigger MTU when compared
to 9216 MTU supported by OcteonTx2 silicon variants. Lookback
interface supports upto 64K and RPM LMAC interfaces support
upto 16K.

This patch does the necessary configuration and adds support
for PF/VF drivers to retrieve max packet size supported via mbox

This patch also configures tx link credit by considering supported
fifo size and max packet length for Octeontx3 silicon.

This patch also removes platform specific name from the driver name.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>