Source needs to write DPCD 103-106 after receiving a PHY request to change
swing/pre-emphasis after reading DPCD 206-207. This is especially needed if
there is a retimer between source and sink and the retimer implements AUX_CH
interception scheme to manage DP PHY settings (e.g. adjusting Swing/Pre-emphasis
equalization level) for DP output channel. If the source doesn't write to
DPCD 103-106, the retimer may not output the requested swing/pre-emphasis and
eventually we fail compliance.

v2: Rebase and use crtc->lane_count (Imre)
Signed-off-by: NKhaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226081554.984307-1-khaled.almahallawy@intel.comReviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>

In verify_mpllb_state() encoder is retrieved from best_encoder
of connector_state. As there will be only one connector_state
for bigjoiner and checking encoder may not be needed for
bigjoiner-slave. This code path related to mpll is done on dg2
and need this fix to avoid null pointer dereference issue.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-30-matthew.d.roper@intel.com

The PSR enable/disable sequences now require that we program an extra
register in the PHY to adjust the lane disable power setting.

Bspec: 49274
Bspec: 53885
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-29-matthew.d.roper@intel.com

Initialization of the PHY is handled by the hardware/firmware, but the
driver should wait up to 25ms for the PHY to report that its calibration
has completed.

Bspec: 49189
Bspec: 50107
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-28-matthew.d.roper@intel.com

DG2 has some changes to the expected modesetting sequences when compared
to gen12.  Adjust our driver logic accordingly.  Although the DP
sequence is pretty similar to TGL's, there are some steps that change,
so let's split the handling for that out into a separate function.

v2:
 - Switch wait_for_us() -> _wait_for() so that we can parameterize the
   timeout rather than duplicating the macro call.  (Jani)

Bspec: 54128
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-27-matthew.d.roper@intel.com

Vswing programming for SNPS PHYs is just a single step -- look up the
value that corresponds to the voltage level from a table and program it
into the SNPS_PHY_TX_EQ register.

Bspec: 53920
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-26-matthew.d.roper@intel.com

At the moment we don't have a proper algorithm that can be used to
calculate PHY settings for arbitrary HDMI link rates.  The PHY tables
here should support the regular modes of real-world HDMI monitors.

Bspec: 54032
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-25-matthew.d.roper@intel.com

DG2's SNPS PHYs incorporate a dedicated port PLL called MPLLB which
takes the place of the shared DPLLs we've used on past platforms.  Let's
add the MPLLB programming sequences; they'll be plugged into the rest of
the code in future patches.

Bspec: 54032
Bspec: 53881
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NNidhi Gupta <nidhi1.gupta@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-24-matthew.d.roper@intel.com

ADL-P now has its own set of DDI buf translation tables (except for eDP
which appears to be the same as TGL).  Add the new values (last updated
in bspec 2021-07-22) to the driver.

v2:
 - Actually hook up the new tables via encoder->get_buf_trans()

v3:
 - Create extra table wrapper structures for the tables from past
   platforms that we're re-using, with names that more accurately
   reflect the link rate they apply to on ADL-P specifically.  (Jose)

Bspec: 49291
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Acked-by: NKhaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728221045.2363614-2-matthew.d.roper@intel.com

The hardware team updates the translation tables on 2021-06-23.  Let's
update the driver accordingly.

Bspec: 49291
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728221045.2363614-1-matthew.d.roper@intel.com

The driver doesn't depend atm on the common mode timing generator
functionality (it would be used for some power saving feature and panel
timing synchronization), however DMC will corrupt the CMTG registers
across DC5 entry/exit sequences unless the CMTG clock gating is
disabled. This in turn can lead to at least the DPLL0/1 configuration
getting stuck at their last state, which means we can't reprogram them
to a new config.

Add the corresponding Bspec workaround to prevent the above.

v2: Fix checkpatch errors. (CI, Jose)

Cc: Uma Shankar <uma.shankar@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134400.101290-1-imre.deak@intel.com

ADL_P requires that we disable underrun recovery when downscaling (or
using the scaler for YUV420 pipe output), using DSC, or using PSR2.
Otherwise we should be able to enable the underrun recovery.

On DG2 we need to keep underrun recovery disabled at all times, but the
chicken bit in PIPE_CHICKEN has an inverted meaning (it's an enable bit
instead of disable).

v2:
 - Reverse the condition (clear the disable bit when supported, set
   disable bit when not supported).

Bspec: 50351
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727145056.2049720-1-matthew.d.roper@intel.com

HDMI and DisplayPort sequences states that audio and PSR should be
disabled before planes are disabled.
Not following it did not caused any problems up to Alderlake-P but
for this platform it causes underruns during the PSR2 disable
sequence.

Specification don't mention that DRRS should be disabled before planes
but it looks safer to switch back to the default refresh rate before
following with the rest of the pipe disable sequence.

BSpec: 49191
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726181559.80855-1-jose.souza@intel.com

PSF GV points are an additional factor that can limit the
bandwidth available to display, separate from the traditional
QGV points.  Whereas traditional QGV points represent possible
memory clock frequencies, PSF GV points reflect possible
frequencies of the memory fabric.

Switching between PSF GV points has the advantage of incurring
almost no memory access block time and thus does not need to be
accounted for in watermark calculations.

This patch adds support for those on top of regular QGV points.
Those are supposed to be used simultaneously, i.e we are always
at some QGV and some PSF GV point, based on the current video
mode requirements.
Bspec: 64631, 53998

v2: Seems that initial assumption made during ml conversation
    was wrong, PCode rejects any masks containing points beyond
    the ones returned, so even though BSpec says we have around
    8 points theoretically, we can mask/unmask only those which
    are returned, trying to manipulate those beyond causes a
    failure from PCode. So switched back to generating mask
    from 1 - num_qgv_points, where num_qgv_points is the actual
    amount of points, advertised by PCode.

v3: - Extended restricted qgv point mask to 0xf, as we have now
      3:2 bits for PSF GV points(Matt Roper)
    - Replaced val2 with NULL from PCode request, since its not being
      used(Matt Roper)
    - Replaced %d to 0x%x for better readability(thanks for spotting)
Signed-off-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531064845.4389-2-stanislav.lisovskiy@intel.com

The fast path only updates cursor register what will not cause
any updates in the screen when using PSR2 selective fetch.

The only option that we have is to go through the slow patch that will
do full atomic commit, that will trigger the PSR2 selective fetch
compute and programing calls.

Without this patch is possible to see a mouse movement lag in Gnome
when PSR2 selective fetch is enabled.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717011227.204494-3-jose.souza@intel.com

Without this planes that were added by intel_psr2_sel_fetch_update()
that intersect with pipe damaged area will not
have skl_program_plane() and intel_psr2_program_plane_sel_fetch()
called, causing panel to not be properly updated.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717011227.204494-2-jose.souza@intel.com

Commit 5a9d38b2 ("drm/i915/display: hide workaround for broken vbt
in intel_bios.c") moved the workaround for broken or missing VBT to
intel_bios.c. However is_port_valid() only protects the handling of
different skus of the same display version. Since in
intel_setup_outputs() we share the code path with version 9, this would
also create port F for SKL/KBL, which does not exist.

Missing VBT can be reproduced when starting a headless QEMU with no
opregion available.

Avoid the issue by splitting versions 9 and 10 in intel_setup_outputs(),
which also makes it more clear what code path it's taking for each
version.

v2: move generic display version after Geminilake since that one has
a different set of outputs

Fixes: 5a9d38b2 ("drm/i915/display: hide workaround for broken vbt in intel_bios.c")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by: NChristoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210722232922.3796835-1-lucas.demarchi@intel.com

A new step has been added to the DP modeset sequences for all platforms
with display version 12 and beyond:  if enabling DP MST with FEC, we
need to set a chicken bit before enabling the transcoder.  The chicken
bit should be disabled again before disabling the transcoder (which we
can do unconditionally since it shouldn't be set anyway in non-MST
cases).

Bspec: 49190, 54128, 55424
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723170618.1477415-1-matthew.d.roper@intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

PORT_A to PORT_F are regular integers defined in the enum port,
while for_each_port_masked requires a bit mask for the ports.

Current given mask: 0b111
Desired mask: 0b111111

I noticed this while Christoph was reporting a bug found on headless
GVT configuration which bisect blamed commit 3ae04c0c ("drm/i915/bios:
limit default outputs to ports A through F")

v2: Avoid unnecessary line continuations as pointed by CI and Christoph

Cc: Christoph Hellwig <hch@infradead.org>
Fixes: 3ae04c0c ("drm/i915/bios: limit default outputs to ports A through F")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Tested-by: NChristoph Hellwig <hch@infradead.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723095225.562913-1-rodrigo.vivi@intel.com

PSR2 is not supported on DG2.

Cc: Caz Yokoyama <Caz.Yokoyama@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714031540.3539704-49-matthew.d.roper@intel.com

Although the bspec labels four of DG2's outputs as "combo PHY," the
underlying PHYs in both cases are actually Synopsys PHYs that are
programmed completely differently than the traditional Intel "combo" PHY
units.  As such, we don't want intel_phy_is_combo to take us down legacy
programming paths, so just return false from it on DG2.  Instead add a
new intel_phy_is_snps() that will return true for all DG2 PHYs.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714031540.3539704-46-matthew.d.roper@intel.com

Add support to load latest DMC version.
The Release Notes mentions that this version fixes
timeout issues.

Cc: Madhumitha Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NMadhumitha Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721215238.24980-4-anusha.srivatsa@intel.com

Add support to the latest DMC firmware.

Cc: Madhunitha Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NMadhumitha Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721215238.24980-3-anusha.srivatsa@intel.com

Lets use RUNTIME_INFO->step since all platforms now have their
stepping info in intel_step.c. This makes intel_get_stepping_info()
a lot simpler.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721215238.24980-2-anusha.srivatsa@intel.com

DG2 doesn't have a SAGV or QGV points that determine memory bandwidth.
Instead it has a constant amount of memory bandwidth available to
display that does not need to be reduced based on the number of active
planes.

For simplicity, we'll just modify driver initialization to create a
single dummy QGV point with the proper amount of memory bandwidth,
rather than trying to query the pcode for this information.

Bspec: 64631
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-19-matthew.d.roper@intel.com

Although the BW_BUDDY registers still exist, they are not used for
anything on DG2.  This change is expected to hold true for future dgpu's
too.

Bspec: 49218
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-17-matthew.d.roper@intel.com

DG2 extends our DDB to four DBuf slices; pipes A+B only have access to
the first two slices, whereas pipes C+D only have access to the second
two.

Confusingly, our bspec decided to switch from 1-based numbering
of dbuf slices (S1, S2) to 0-based numbering (S0, S1, S2, S3) in
Display13.  At the moment we're using the 0-based number scheme for the
DBUF_CTL_S() register addressing, but the 1-based number scheme in the
actual slice assignment tables.  We may want to consider switching the
assignment over to 0-based numbering too at some point...

Bspec: 49255
Bspec: 50057
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-16-matthew.d.roper@intel.com

DG2 has outputs on DDI A-D attached to what the bspec diagram shows as
"Combo PHY A-D."  Note that despite being labelled "combo" the PHYs on
these outputs are Synopsys PHYs rather than traditional Intel combo PHY
technology.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-15-matthew.d.roper@intel.com

On DG2 we're supposed to just wait 600us after programming the well
before moving on; there won't be an ack from the hardware.

Bspec: 49296
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-14-matthew.d.roper@intel.com

DG2 has no shared DPLL's or DDI clock muxing.  The Port PLL is embedded
within the PHY.

Bspec: 54032
Bspec: 54034
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-13-matthew.d.roper@intel.com

Note that DG2 only has a single possible refclk frequency (38.4 MHz).

v2:
 - Drop two now-unused cdclk entries

Bspec: 54034
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-12-matthew.d.roper@intel.com

Workarounds are documented in the bspec with an exclusive upper bound
(i.e., a "fixed" stepping that no longer needs the workaround).  This
makes our driver's use of an inclusive upper bound for stepping ranges
confusing; the differing notation between code and bspec makes it very
easy for mistakes to creep in.

Let's switch the upper bound of our IS_{GT,DISP}_STEP macros over to use
an exclusive upper bound like the bspec does.  This also has the benefit
of helping make sure workarounds are properly handled for new minor
steppings that show up (e.g., an A1 between the A0 and B0 we already
knew about) --- if the new intermediate stepping pulls in hardware fixes
early, there will be an update to the workaround definition which lets
us know we need to change our code.  If the new stepping does not pull a
hardware fix earlier, then the new stepping will already be captured
properly by the "[begin, fix)" range in the code.

We'll probably need to be extra vigilant in code review of new
workarounds for the near future to make sure developers notice the new
semantics of workaround bounds.  But we just migrated a bunch of our
platforms from the IS_REVID bounds over to IS_{GT,DISP}_STEP, so people
are already adjusting to the new macros and now is a good time to make
this change too.

[mattrope: Split out display changes to apply through intel-next tree]
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-8-matthew.d.roper@intel.com

RKL doesn't have PSR2 support, so PSR2-related workarounds no longer
apply.

Bspec: 53273
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-7-matthew.d.roper@intel.com

Bspec: 53273
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-6-matthew.d.roper@intel.com

Currently when we do the HW state readout, we dont set the shared dpll to NULL
for the bigjoiner slave which should not have a DPLL assigned. So it has
some garbage while the HW state readout is NULL. So explicitly reset
the shared dpll for bigjoiner slave pipe.

Bug: https://gitlab.freedesktop.org/drm/intel/-/issues/3465
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Tested-by: NSwati Sharma <swati2.sharma@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714223414.9849-1-manasi.d.navare@intel.com

This is now a requirement for all display 12 and newer, not only for
tigerlake.

BSpec: 50422
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625235600.765677-2-jose.souza@intel.com

Implements changes around PSR for alderlake-P:

- EDP_SU_TRACK_ENABLE was removed and bit 30 now has other function
- Some bits of PSR2_MAN_TRK_CTL moved and SF_PARTIAL_FRAME_UPDATE was
  removed setting SU_REGION_START/END_ADDR will do this job
- SU_REGION_START/END_ADDR have now line granularity but will need to
  be aligned with DSC when the PSRS + DSC support lands

BSpec: 50422
BSpec: 50424
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625235600.765677-1-jose.souza@intel.com

Set DSC BPP to the value forced through
debugfs. It can go from bpc to bpp-1.

v2: Use default dsc bpp when we are just
    doing force_dsc_en, use default dsc bpp
    for invalid force_dsc_bpp values. (Jani)
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NSwati Sharma <swati2.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720064907.9771-4-vandita.kulkarni@intel.com

This patch creates a per connector debugfs node to expose
the Compressed BPP. The same node can be used from userspace
to force DSC to a certain BPP(all accepted values).

This is useful to verify all supported/requested
compression bpp's through IGT

v2: Remove unnecessary logic (Jani)
v3: Drop pipe bpp in debugfs node (Vandita)
v4: Minor cleanups (Vandita)
v5: Fix NULL pointer dereference
v6: Fix dim tool checkpatch errors
    Release the lock before return (Vandita)
v7: Rename to file to dsc_bpp, remove unwanted
    dsc bpp range check from v6, permissions (Jani)

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Navare Manasi D <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NPatnana Venkata Sai <venkata.sai.patnana@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720064907.9771-3-vandita.kulkarni@intel.com

Though there is a write option available on  fec_suport
debugfs file, so far it has been registering with read
permissions only.
Suggested-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720064907.9771-2-vandita.kulkarni@intel.com