On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.

We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.

And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.

Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

During readout we cannot assume the planes are actually using the
slices they are supposed to use. The BIOS may have misprogrammed
things and put the planes onto the wrong dbuf slices. So let's
do the readout more carefully to make sure we really know which
dbuf slices are actually in use by the pipe at the time.

Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-2-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Reintroduce the !join_mbus single pipe cases for adlp+.

Due to the mbus relative dbuf offsets in PLANE_BUF_CFG we
need to know the actual slices used by the pipe when doing
readout, even when mbus joining isn't enabled. Accurate
readout will be needed to properly sanitize invalid BIOS
dbuf configurations.

This will also make it much easier to play around with the
!join_mbus configs for testin/workaround purposes.

Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-1-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Make sure all unused power wells left enabled by BIOS get disabled
during driver loading and system resume.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5028Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202104249.2680843-1-imre.deak@intel.com

Architectures others than x86 have a stub implementation calling
WARN_ON_ONCE(). The appropriate headers need to be included, otherwise
the header-test target will fail with:

  HDRTEST drivers/gpu/drm/i915/i915_mm.h
In file included from <command-line>:
./drivers/gpu/drm/i915/i915_mm.h: In function ‘remap_io_mapping’:
./drivers/gpu/drm/i915/i915_mm.h:26:2: error: implicit declaration of function ‘WARN_ON_ONCE’ [-Werror=implicit-function-declaration]
   26 |  WARN_ON_ONCE(1);
      |  ^~~~~~~~~~~~

v2: Do not include <linux/printk.h> since call to pr_err() has been
removed

Fixes: 67c430bb ("drm/i915: Skip remap_io_mapping() for non-x86 platforms")
Cc: Siva Mullati <siva.mullati@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NSiva Mullati <siva.mullati@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220131165926.3230642-3-lucas.demarchi@intel.com

Following what was done in drm_cache.c, when the stub for
remap_io_mapping() was added in commit 67c430bb ("drm/i915: Skip
remap_io_mapping() for non-x86 platforms"), it included a log message
with pr_err().  However just the warning is already enough and switching
to WARN_ONCE() allows us to keep the log message while avoiding log
spam.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220131165926.3230642-4-lucas.demarchi@intel.com

A couple hunks didn't get applied while resolving the conflicts on
commit 0d6419e9 ("drm/i915: Move GT registers to their own header
file").  Add the second half of the patch as a follow-up commit.

Fixes: 0d6419e9 ("drm/i915: Move GT registers to their own header file")
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-6-matthew.d.roper@intel.com

Several of our i915 header files, have been including i915_reg.h.  This
means that any change to i915_reg.h will trigger a full rebuild of
pretty much every file of the driver, even those that don't have any
kind of register access.  Let's delete the i915_reg.h include from all
headers and add an explicit include from the .c files that truly
need the register definitions; those that need a definition of
i915_reg_t for a function definition can get it from i915_reg_defs.h
instead.

We also remove two non-register #define's (VLV_DISPLAY_BASE and
GEN12_SFC_DONE_MAX) into i915_reg_defs.h to allow us to drop the
i915_reg.h include from a couple of headers.

There's probably a lot more header dependency optimization possible, but
the changes here roughly cut the number of files compiled after 'touch
i915_reg.h' in half --- a good first step.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-7-matthew.d.roper@intel.com

This is a huge, chaotic mass of registers copied over as-is without any
real cleanup.  We'll come back and organize these better, align on
consistent coding style, remove dead code, etc. in separate patches
later that will be easier to review.

v2:
 - Add missing include in intel_pxp_irq.c
v3:
 - Correct a few indentation errors (Lucas)
 - Minor conflict resolution

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-6-matthew.d.roper@intel.com

The various MI_PREDICATE registers have per-engine instances.  Today we
only utilize the RCS0 instance of each, but that will likely change in
the future; switch to parameterized register definitions to make these
easier to work with going forward.

Of special note is MI_PREDICATE_RESULT_2; we only use it in one place in
the driver today in HSW-specific code.  It turns out that the bspec
(page 94) lists two different offsets for this register on HSW; one is
in the standard location shared by all other platforms (base + 0x3bc)
and the other is an unusual location (0x2214).  We're using the second,
non-standard offset in i915 today; that offset doesn't exist on any
other platforms (and it's not even 100% clear that it's correct for HSW)
so I've renamed the current non-standard definition to
HSW_MI_PREDICATE_RESULT_2; the new cross-platform parameterized macro
(which is still unused at the moment) uses the standard offset.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-5-matthew.d.roper@intel.com

At the moment we only use R_PWR_CLK_STATE in the context of the RCS
engine, but upcoming support for compute engines will start using
instances relative to the CCS engine base offsets.  Let's parameterize
the register and move it to the engine reg header.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-4-matthew.d.roper@intel.com

Let's use 'struct i915_range' to express sets of b-counter and mux
registers in the perf code.  This makes the code more similar to how we
handle things like multicast register ranges, forcewake tables, shadow
tables, etc. and also lets us avoid needing symbolic register name
definitions for the various range end points.  With this change, many of
the OA register definitions are no longer used in the code, so we can
drop their #define's for simplicity.

v2:  Drop 'inline' from reg_in_range_table().  (Jani)

v3:  Split the first range in gen12_oa_mux_regs[] so that 0xd08 isn't
     whitelisted.  (Umesh)

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Acked-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NUmesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-3-matthew.d.roper@intel.com

The OA unit registers are only used by the perf code; move them to their
own header file.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-2-matthew.d.roper@intel.com

The only user of the VGA registers has switched to using the definitions
in linux/vga.h, so these have become redundant. Remove them.
Suggested-by: NMatt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202112509.1886660-2-jani.nikula@intel.com

The video/vga.h has macros for the VGA registers. Switch to use them.

v2: Use direct 0x01 instead of the confusing VGA_SEQ_CLOCK_MODE (Ville)
Suggested-by: NMatt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202112509.1886660-1-jani.nikula@intel.com

Use DISPLAY_VER rather than GRAPHICS_VER to determine
availability of display hardware features.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124193136.2397-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

When reprogramming M/N live on BDW+ we must write the LINK_N
register last as it's the one that arms the double buffered
register update for all the M/N registers. Document this so
that we don't accidentally break things.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-18-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

No point in special casing the check of dp_m2_n2 on pre-bdw platforms.
Either the transcoder has M2/N2 in which case the values should be
set to something sensible, or it doesn't in which case dp_m2_n2 is
always zeroed.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-17-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

No point in special casing the dp_m2_n2 dumping. Just do it always.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-16-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Program the PCH transcoder M2/N2 values appropriately. We're
still missing a few things for PCH port DRRS but at least this
means we can do readout/state check for dp_m2_n2 unconditionally.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-15-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Make life simpler by always programming DP M2/N2 with a consistent
value. This will lets use do state readout+chec unconditionally.

I was first going to just set M2/N2=M1/N1 but then it occurred
to me that it might interfere with fastboot on account of BIOS
likely leaving the registers zeroed. So let's zero out the values
instead (except TU where a zero register value actually means '1').
Still not sure that's the best approach but lets go with it for
now.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-14-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

M2/N2 values are present for all ilk-ivb,vlv,chv (and hsw edp).
Make the code reflect that.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-13-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Pull the "can we do DRRS?" check into helper in order
to reduce the clutter in intel_drrs_compute_config().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-12-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Currently we allow DRRS on IVB PCH ports, but we're missing a
few programming steps meaning it is guaranteed to not work.
And on HSW DRRS is not supported on anything but port A ever
as only transcoder EDP has the M2/N2 registers (though I'm
not sure if HSW ever has eDP on any other port).

Starting from BDW all transcoders have the dynamically
reprogrammable M/N registers so DRRS could work on any
port.

Stop initializing DRRS on ports where it cannot possibly work.

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-11-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Follow the path laid out by hsw+ and extract helpers to configure
the cpu transcoder for earlier platforms as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-10-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Let's do the cpu transcoder M/N setup next to where we program
most other cpu transcoder timings/etc.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-9-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Do the PCH transcoder M/N setup next to where all the other
PCH transcoder stuff is programmed. Matches the spec modeset
sequence better.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-8-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Instead of passing in the whole crtc state let's pass in just
the bits of state we need. This will help with the DRRS code
which shouldn't really be accessing the atomic state stuff directly
as it gets called outside the normal atomic flows.

v2: Fix set_m1_n1 vs. set_m2_n2 fumble for i9xx (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-7-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

As with intel_cpu_transcoder_set_m_n() let's split the readout
counterpart into explicit M1/N1 vs. M2/N2 variants as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-6-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Make things a bit more explicit by splitting
intel_cpu_transcoder_set_m_n() into separate variants for M1/N1 vs.
M2/N2. Makes the DRRS M/N programming at least more obvious.

Note that for the MST and DRRS cases we don't need to call the
M2/N2 variant at all since the transcoders that support those
do not have the M2/N2 registers.

Same could be said for i9xx_crtc_enable() but I want to do a
higher level code sharing between that valleyview_crtc_enable()
later in which case we do need the M2/N2 variant. This is also
why I keep the transcoder_has_m2_n2() in intel_cpu_transcoder_set_m2_n2()
so the caller doesn't have necessarily care what the chosen
transcoder supports.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-5-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Get rid of the entirely pointless ilk_get_fdi_m_n_config() wrapper
and just call the CPU transcoder function directly.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

As with intel_dp_set_m_n() let's get rid of the wrapper and just
call the relevant PCH vs. CPU transcoder functions directly.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-3-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

I want to make a clean split betwen the CPU vs. PCH transcoder
programming. To that end eliminate intel_dp_set_m_n() and just
call the individual CPU/PCH transcoder functions directly.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-2-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Don't see why we should skip the wakeref tracking when the
platform doesn't support runtime pm. We still want all the
code to be 100% leak free so let's track this unconditionally.

Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com> # stackdepot
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126081539.23227-2-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

We call __save_depot_stack() unconditionally so the stack depot
must always be initialized or else we'll oops on platforms without
runtime pm support.

Presumably we've not seen this in CI due to stack_depot_init()
already getting called via drm_mm_init()+CONFIG_DRM_DEBUG_MM.

Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com> # stackdepot
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Fixes: 2dba5eb1 ("lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126081539.23227-1-ville.syrjala@linux.intel.comAcked-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NImre Deak <imre.deak@intel.com>

Catch-up with 5.17-rc2 and trying to align with drm-intel-gt-next
for a possible topic branch for merging the split of i915_regs...
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Pull irq fixes from Borislav Petkov:

 - Drop an unused private data field in the AIC driver

 - Various fixes to the realtek-rtl driver

 - Make the GICv3 ITS driver compile again in !SMP configurations

 - Force reset of the GICv3 ITSs at probe time to avoid issues during kexec

 - Yet another kfree/bitmap_free conversion

 - Various DT updates (Renesas, SiFive)

* tag 'irq_urgent_for_v5.17_rc2_p2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: interrupt-controller: sifive,plic: Group interrupt tuples
  dt-bindings: interrupt-controller: sifive,plic: Fix number of interrupts
  dt-bindings: irqchip: renesas-irqc: Add R-Car V3U support
  irqchip/gic-v3-its: Reset each ITS's BASERn register before probe
  irqchip/gic-v3-its: Fix build for !SMP
  irqchip/loongson-pch-ms: Use bitmap_free() to free bitmap
  irqchip/realtek-rtl: Service all pending interrupts
  irqchip/realtek-rtl: Fix off-by-one in routing
  irqchip/realtek-rtl: Map control data to virq
  irqchip/apple-aic: Drop unused ipi_hwirq field

Pull perf fixes from Borislav Petkov:

 - Prevent accesses to the per-CPU cgroup context list from another CPU
   except the one it belongs to, to avoid list corruption

 - Make sure parent events are always woken up to avoid indefinite hangs
   in the traced workload

* tag 'perf_urgent_for_v5.17_rc2_p2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix cgroup event list management
  perf: Always wake the parent event

Pull scheduler fix from Borislav Petkov:
 "Make sure the membarrier-rseq fence commands are part of the reported
  set when querying membarrier(2) commands through MEMBARRIER_CMD_QUERY"

* tag 'sched_urgent_for_v5.17_rc2_p2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/membarrier: Fix membarrier-rseq fence command missing from query bitmask