When the RX skb allocation failed, we should recycle
the previously allocated skbuffer. By calling return
we would kill the RX queue completely since the
entry would be invalidated.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to the PLCP signal and bitrates values,
we should validate the MCS value from the RX descriptor
before sending it to mac80211.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The watchdog function must run on a work_queue
which is independent of any other work inside rt2x00.

The main reasons, being that a broken work on the mac80211
work_queue can otherwise prevent the watchdog to run (while
in fact the watchdog could fix the issue). And on the other
hand because the watchdog relies on the completion of the
completion handlers for RX/TX which for the USB case, occur
on the mac80211 workqueue.

This fixes some "Queue %d failed to flush" errors, which were
caused by the watchdog function waiting on the completion
handler which was scheduled to run right after the watchdog.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A lot of functions accept a struct rt2x00_dev combined with
either a struct queue_entry or struct data_queue argument.
This can be simplified by only passing on the queue/entry
argument.

In cases where rt2x00_dev and a sk_buff are send together,
we can send the queue_entry instead.

rt2x00usb_alloc_urb and rt2x00usb_free_urb have a bit
of vague naming. Instead they allocate all the data which
belongs to a rt2x00 data queue entry.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stanse found that urb cannot be NULL in at76_rx_tasklet because it is
dereferenced earlier, so remove the unneeded check.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch attempts to ensure that ath9k's built-in rate control algorithm
does not rely on the value of the ampdu_len and ampdu_ack_len tx status
fields unless the IEEE80211_TX_STAT_AMPDU flag is set.

This patch has not been tested.

Cc: <stable@kernel.org>
Signed-off-by: NBjörn Smedman <bjorn.smedman@venatech.se>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the following problems with the rate control feedback
generated by ath9k for A-MPDU frames:

1. Rate control feedback is carried on the first frame of an aggregate
that is either ACKed, or has execeeded the software retry count and is
considered failed. However, ath9k would incorrectly assume the aggregate
had the length 1 if one of these conditions did not apply to the first
frame of the aggregate, but instead a later frame. This fix therefor
copies the bf_nframes field of the buffer in the same manner as the rates
field of the tx status.

2. Sometimes the ampdu_len and ampdu_ack_len fields of the tx status was
left uninitialized eventhough the IEEE80211_TX_STAT_AMPDU flag was set.
This is now avoid by setting flag and fields in the same place.

3. Even if a frame has been selected for aggregation by mac80211 and
marked with the IEEE80211_TX_CTL_AMPDU flag it can sometimes happen that
ath9k transmits the frame without aggregation. In these cases the
ampdu_ack_len field could be incorrectly computed because the nbad
parameter to ath_tx_rc_status was incorrect.

Cc: <stable@kernel.org>
Signed-off-by: NBjörn Smedman <bjorn.smedman@venatech.se>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1271 driver is under heavy development but on the other hand the older
wl1251 driver is currently considered more as a legacy driver. To make it
easier to develop wl1271 features move wl1251 to it's own directory,
drivers/net/wireless/wl1251.

There are no functional changes, only moving of files. One regression
is that Kconfig won't be updated automatically and user needs to enable
wl1251 manually with an older config file.
Signed-off-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In preparation of moving wl1251 out from drivers/net/wireless/wl12xx
create a separate copy of wl12xx_80211.h.

This file should not even exist, we should instead use generic ieee80211
definitions. This will be fixed in the future so that the file can
be removed.
Signed-off-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the past, carl9170 has been plagued by mysterious
ghosts.

e.g.:
 wlan4: deauthenticated from 02:04:d8:3c:ac:c1 (Reason: 0)

Apparently, the AP sent us a bogus deauthentication
notification. But upon closer inspection the
"management frame" turned out to be a corrupted
scrap of an unsuccessful A-MPDU.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The total/fatal error bit was erroneously prefixed
with AR9170_RX_ERROR instead of AR9170_RX_STATUS.
Luckily, the hardware specification confirmed that
the 0x80 flag will never be set for mac->error.
So, it was always just a dead branch.

This patch also imports the latest version of
shared wlan.h header from the firmware git.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces several identical frame drop
paths with a single shared rx frame error handler.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patches "rt2x00: Improve TX status entry validation" and "rt2x00: rework tx
status handling in rt2800pci" together were causing problems with tx status
processing in rt2800pci:

phy1 -> rt2800pci_txdone: Warning - Got TX status for an empty queue 3, dropping
phy1 -> rt2800pci_txdone: Warning - Got TX status for an unavailable queue 7, dropping

Fix this by using the correct field definition for getting the QID out of the
tx status report.
Reported-by: NLuis Correia <luis.f.correia@gmail.com>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Tested-by: NLuis Correia <luis.f.correia@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to initialize qidx to zero as it will ever be
overwritten by the correct value.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is an error condition that is not supposed to happen. Hence, it is
safe to add unlikely to this check.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since no skb will be mapped for RX and TX at the same time we can
simply shortcut the check for SKBDESC_DMA_MAPPED_TX.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Results for the active channel are updated whenever a new survey dump
is requested, the old data is kept to allow multiple processes to
make their own channel utilization averages.
All other channels only contain the data for the last time that the
hardware was on the channel, i.e. the last scan result or other
off-channel activity.
Running a background scan does not clear the data for the active
channel.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This prevents random memory corruption if the number of channels ever gets
changed without an update to the internal channel array size.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of keeping track of wraparound, clear the counters on every
access and keep separate deltas for ANI and later survey use.
Also moves the function for calculating the 'listen time' for ANI
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, if there is an AP and a STATION, and AP
is removed, the NIC will not revert back to STATION mode.
Reported-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Helps debug multi-VIF scenarios.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add required suspend/resume support to prevent the SDIO
core from removing our card completely during system suspend.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Tested-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Enable runtime PM for the wl1271 SDIO device.

We request power whenever the WLAN interface is brought up,
and release it after the WLAN interface is taken down.

As a result, power is released immediately after probe returns,
since at that point power has not been explicitly requested yet
(i.e. the WLAN interface is still down).
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Tested-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

6000g2 devices need to have temperature offset calibration. The runtime
uCode needs to receive the calibration results just like BB and LO
calibration. To do this, driver reads the offset value from NVM and send
it to uCode after runtime uCode is alive.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn driver uses the IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE
as the chain noise reset calibration index and
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE+1 as the chain noise gain
calibration index, if not specified by the TLV value in the new
firmware format.

However, this is broken if we need to add more calibrations like
the temperature offset calibration because we increased
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE by 1.

To fix this issue, define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE
and use it as the calibration index instead. We still keep the
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE as a sanity check for
the TLV value given by ucode.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For experimental uCode, it should work with the driver
if driver has experimental uCode support option enabled;
remove the API version checking.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The recent scanning code shuffle accidentally
moved the SCAN_HW bit setting _after_ the PAN
parameters are modified, which means that they
don't take the scan into account -- fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The function is used exactly once, and the caller
doesn't even need the special check, it can be
simplified to a simple bit check.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

A number of declarations in iwl-core.h should
be in agn specific files, and also rename the
iwl-calib.h file to iwl-agn-calib.h to better
reflect that it belongs to agn.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since all devices share the same operation here,
there's no need to call it indirectly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The set_pwr_src operation is only ever used from
within the same sub-driver that it is declared
in, so it can just be called directly instead of
being an operation. Also, it is never called to
set the power source to V_aux, so change the two
functions accordingly (but keep the V_aux code
for documentation purposes in a comment).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>