The oversampling rate of the DAC and ADC can be controlled to optimise
for either low power consumption or maximum performance.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Tune the FLL gain for optimal performance according to evaluation
results.
Signed-off-by: NMario Becroft <mb@gem.win.co.nz>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Acc to WM8580 manual, the default value for R8 is 0x10, not 0x1c.
Signed-off-by: NSeungwhan Youn <sw.youn@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Deemphasis control's .get callback should update control's value instead
of returning it - return value of callback function is used for indicating
error or success of operation.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NUk Kim <w0806.kim@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Fix mismerge from the out of tree BSP where this support was developed.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In case of SNDRV_PCM_FORMAT_S32_LE, we need to set WM8580_AIF_LENGTH_32,
rather than WM8580_AIF_LENGTH_24.
Also, the BCLK has to be 64fs, for sample size of 20, 24 and 32 bits.
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

SPKOUTL_BOOST start from third bit, SPKOUTLR_BOOST start from 0 bit.
Signed-off-by: NUk Kim <w0806.kim@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

When we disable the WM8994 FLL code path sharing means that we end up
writing out a configuration. Currently this is the currently active
input and output frequency (which causes snd_soc_update_bits() to
suppress actual writes both immediately and in the common case where
we reenable the same configuration later) but we allow machine drivers
to pass through a source of zero. Since the register values written
are one less than the source constants this causes corruption of other
bitfields in the register.

Fix this by using the most recently configured FLL source when none is
provided.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

We want the index of DAI's driver here.
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In alc5623_i2c_probe(),
the default case for checking alc5623->id behaves the same as case 0x23.
However, In alc5623_probe() the default case for checking alc5623->id
becomes to be the same as case 0x21.
This makes the meaning of default case inconsistent.

Since we have checked codec id in alc5623_i2c_probe() by comparing
vid2 with id->driver_data, it is not possible to run into the default case now.

In case we may add more supported devices to alc5623_i2c_table in the future,
this patch changes the default case return -EINVAL to let people know that
they should not run into this case. They should also add a new case accordingly
for the new id.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Update some of the default configuration for the device to improve
the performance.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The deemphasis filter should be selected based on sample rate for
optimal performance.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This is much more maintainable than the array.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The mute/unmute is controled by SMUTE (Soft Mute Control bit):
        0: Normal Operation (Default)
        1: DAC outputs soft-muted

I think this change improves readability.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

We need a post notification as we need to shut down the MBC after the
data stops flowing rather than before.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

According to the datasheet the bypass path enable/disable is
bit 3 therefore we need 0x8 and not 0x4.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Simplify pm860x_probe error handling and return actual error code we got.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This allows us to communicate our power management state back to the
parent device, allowing it to do a full power down when the device is
idle.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8994 and WM8958 register map is relatively sparse so benefits
from compression. The rbtree compression gives better results than
LZO for both memory and CPU consumption on a map as sparse as this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In the process we convert the driver to read registers one at a time
when initialising the cache. This has the effect of working around
limitations in the sizes of I2C transactions which can be done by some
CPUs. Due to the sparseness of the register map the overhead from this
should be minimual unless I2C transactions are very expensive to start.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 contains an advanced accessory detection feature which allows
detection of up to seven different impedence levels on the microphone
bias output, including detection of video outputs. Since some of the
more involved accessory interfaces may involve noticable interactions
with external components a simple detection scheme is provided by
default with the option to provide custom handling of accessory detect.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 features a multi-band compressor which can be enabled on
any of the AIF inputs. The MBC allows different gains to be applied to
differnt audio bands, providing an improvement in perceived loudness
of the signal by avoiding overdriving the output transducers. This
patch enables support for the MBC.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Additional audio routing options are available on the WM8958 audio
interface 3. Add support for these.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 is a WM8994 derivative. This patch merely ensures that some
revision specific configuration for WM8994 is not enabled on WM8994,
additional patches will add support for the new features introduced on
the WM8958.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Devices which do not have a DCS correction applied can use the explicit
DC servo startup mode for optimal startup performance. This most
immediately affects the WM8958.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

If aic3x_read failed , val is used uninitialized.
Fix it by initializing val to 0.

This patch fixes below compile warning:
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_get_gpio':
sound/soc/codecs/tlv320aic3x.c:1183: warning: 'val' may be used uninitialized in this function
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_headset_detected':
sound/soc/codecs/tlv320aic3x.c:1211: warning: 'val' may be used uninitialized in this function
sound/soc/codecs/tlv320aic3x.c: In function 'aic3x_button_pressed':
sound/soc/codecs/tlv320aic3x.c:1219: warning: 'val' may be used uninitialized in this function
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8737 is a low power, flexible stereo ADC designed for portable
applications. This driver supports most of the functionality of the
WM8737, though some features such as the ALC are not yet implemented.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

MCLKDIV bit of Register 04h Clocking1:
	0 : Divide by 1
	1 : Divide by 2

Thus in the case of freq <= 16500000, we should clear MCLKDIV bit.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

DACSLOPE bit of Register 06h ADC and DAC Control 2:
        0: Normal mode
        1: Sloping stop-band mode

Thus in the case of normal mode, we should clear DACSLOPE bit.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>