A new MMU hwmod class and data structures are created
to represent the MMUs within the IPU and DSP processor
subsystems in OMAP5. The MMUs in OMAP5 are identical to
those in OMAP4.

Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: NSuman Anna <s-anna@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP iommu driver performs the reset management for the
iommu instances in processor sub-systems using the omap_device
API which are currently supplied as platform data ops. Use pdata
quirks to maintain the functionality as the OMAP iommu driver
gets converted to use DT nodes, until the reset portions are
decoupled from omap_hwmod/omap_device into a separate reset
driver.

This patch adds the pdata quirks for the reset management of
iommus within the DSP (OMAP3 & OMAP4) and IPU subsystems (OMAP4).
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The IOMMU DT adaptation support uses the device name instead
of an iommu object name. Fixup the ISP device archdata MMU
name at runtime if using DT-boot. This allows the OMAP3 camera
to be functional in both legacy and DT boots. The iommu object
names should eventually vanish when all the IOMMU users have
been converted to DT nodes.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The IVA MMU is not functional when used through the hwmod and
omap_device layers. Add fixes to clockdomain and hwmod data
to have it functional. The hwmod changes are needed to enable
the clock, and the SWSUP change is needed to wakeup the domain
because the power domain is programmed to be in RET, and there
is no automatic power domain switching to ON.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

CONFIG_OMAP_IOMMU_IVA2 was defined originally to avoid conflicting
usage by tidspbridge and other iommu users. The same can be achieved
by marking the DT node disabled, so remove this obsolete flag and
the corresponding hwmod data can be enabled.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: revise commit log]
Signed-off-by: NSuman Anna <s-anna@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

EVM board provides two Ethernet ports, this patch sets them into
dual_emac mode to provide two independent network interfaces.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ABB device nodes for OMAP443x family of devices. abb_iva is
populated, but disabled as it is not used on current OMAP443x family,
but the node is used on OMAP446x family. Data is based on OMAP443x
Technical Reference Manual revision AN (April 2013).

ABB device nodes for OMAP4460 device Data is based on OMAP4460
Technical Reference Manual revision Z (April 2013)

[nm@ti.com: co-developer]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NAndrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ABB device node for OMAP36xx family of devices. Data is based on
OMAP36XX Technical Reference Manual revision AB (Dec 2012).

[nm@ti.com: co-developer]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NAndrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add card detect gpio for SD card slot and include dt gpio header.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add card detect gpio for SD card slot
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

enable sd card slot on am437x-gp-evm
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Added device tree bindings for dwc3, usb2 and usb3 PHYs. The documentation
of these can be found at Documentation/devicetree/bindings/phy/phy-bindings.txt
and Documentation/devicetree/bindings/phy/ti-phy.txt.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable the WiLink6 connected to mmc2.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove non-compatible id from examples.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP EHCI and OHCI controllers are not compatible with drivers
other than "ti,ehci-omap" and "ti,ohci-omap3" respectively, so get
rid of the incompatible ids.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.

Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gumstix DuoVero is an OMAP4430-based Computer On Module.
Parlor is one of the available expansion board.

Tested features:
- GPMC ethernet
- HSUSB2 and OTG
- Audio out
- WiFi and Bluetooth (w2cbw0015 SDIO module)
- LED and button
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge tag 'for_3.15/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.15/dt

Add craneboard devices
Add more N900 devices
Add am43x-epos-evm and am437x-gp-evm devices
Add OMAP4 DMM devices

Conflicts:
	arch/arm/boot/dts/am43x-epos-evm.dts
	arch/arm/boot/dts/dra7.dtsi

Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.

Add documentation for the DMM bindings.

Originally worked on by Andy Gross <andygro@gmail.com>

Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add gpio keys node for am43x gp evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This patch:
 - enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
 - adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
   present on following boards:

   am43x-epos-evm:
	On this board, NAND Flash control lines are muxed with QSPI, Thus only
        one of the two can be used at a time. Selection is controlled by:
        (a) dynamically driving following GPIO pin from software
            GPMC_A0(GPIO) == 0 NAND is selected (default)
            GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
    commit ac65caf5
    ARM: OMAP2+: cleaned-up DT support of various ECC schemes
    Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch has following updates, specific to MTD/NAND DT
 - update MTD NAND partition table to keep compatibility between
   different boards and mainline u-boot.
 - prefix 'NAND.' in names of NAND device MTD partitions to differentiate them
   from other MTD device partitions (like NOR and QSPI)
               Partition_Name            Partition_Size
    /dev/mtd0  NAND.SPL                  1 block-size*
    /dev/mtd1  NAND.SPL.backup1          1 block-size*
    /dev/mtd2  NAND.SPL.backup2          1 block-size*
    /dev/mtd3  NAND.SPL.backup3          1 block-size*
    /dev/mtd5  NAND.u-boot-spl-os        2 block-size* [for falcon boot]
    /dev/mtd4  NAND.u-boot               1 MB
    /dev/mtd6  NAND.u-boot-env           1 block-size*
    /dev/mtd7  NAND.u-boot-env.backup1   1 block-size*
    /dev/mtd8  NAND.kernel               till 0xA00000
    /dev/mtd9  NAND.file-system          till end of device

* am335x-evm uses NAND device with block-size=128KiB
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch
 - refactors gpmc_hwecc_bch_capable()
 - add checks for new platforms like dra7xx, am43xx
 - add checks for OMAP3 SoC, w.r.t. new ECC schemes spawned in following commit:
    commit ac65caf5
    ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add node for bma180 driver.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This requires vaux4.

Reset line isn't used yet, so wifi isn't reliable.
But it does work once per boot.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds basic sound support for gta04 board.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define twl4030 charger node used for charging.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gta04 using tcs2007 touchscreen. Add support for that.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add magnetometer hmc5843 node.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add pwm backlight support for gp evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add SPI dts data.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add I2C2 dts data.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AM43xx devices have an extra MUX_MODE for certain pins.
Updating dt include to have MUX_MODE8 which maps to 0x8.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add pwm backlight support for am43x epos evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add "pwm-cells" node for all ecap, ehrpwm in am43x dtsi files.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This adds support for the bq24150a chip to the
Nokia N900 DTS file.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>