TRIM support added through vendor unique command.

Signed-off-by: Sam Bradshaw < sbradshaw@micron.com>
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This patch contains
	* parallel command completion using workers
	* bind the workers to the chosen numa node
	* bind isr to the chosen numa node
	* allocating memory in the chosen numa node
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSam Bradshaw <sbradshaw@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Hi Jens,

Another tiny patch.

Removed __packed before the struct smart_attr and added __packed at end of
the structure to fix padding issue.
Signed-off-by: NSelvan Mani  <smani@micron.com>
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The dereference to port should be moved below the NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

If we're building a 32-bit kernel and CONFIG_LBADF isn't set,
sector_t is 32-bits wide. The shifts by 32 and 40 are thus
larger than we support.

Cast the sector offset to a u64 to avoid these warnings.
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Previous commit use value 3 for erasemode mask.
Changing the mask to correct value to 2
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Earlier lba address was assigned directly to lba_low and lba_low_ex,
which would result in a different number (bytes reversed) in
big-endian systems. Now assigning lba address byte-by-byte to fis.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The mtip driver lifted this code from elsewhere and then added a special
handling check for SEC_ERASE_UNIT. If the caller tries to do a security
erase but passes no output data for the command then outbuf is not
allocated and the driver duly explodes.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Added appropriate timeout value for secure erase based on identify device data
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Current user_buffer check is incorrect and causes hdparm to fail

# hdparm -I /dev/rssda
 HDIO_DRIVE_CMD(identify) failed: Input/output error

/dev/rssda:

Patching linux-3.6-rc5 hdparm works as expected

# hdparm -I /dev/rssda
/dev/rssda:

ATA device, with non-removable media
	Model Number:       DELL_P320h-MTFDGAL350SAH
	Serial Number:      00000000121302025F01
	Firmware Revision:  B1442808
<snip>
Reported-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Removed the dead code in mtip_hw_read_registers() and mtip_hw_read_flags().

Reported-by: Coverity
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Changed printk to be compliant with latest style changes
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Proper reporting of write protect status on big-endian
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Increased timeout for standby command to work with larger capacity drives
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Return error for NCQ commands when the drive is in security locked state
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Added supported device IDs in pci table
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSelvan Mani <smani@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

On module load, creates a debugfs parent 'rssd' in debugfs root. Then for each
device, create a new node with corresponding disk name. Under the new node, two
entries 'registers' and 'flags' are created.

NOTE: These entries were removed from sysfs in the previous patch
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This patch removes entries 'registers' and 'flags' from sysfs. Updated ABI file
to reflect this change.
Reported-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

version.h header file inclusion is no longer required.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>

* Formatted the output of 'registers' entry
* Added "Commands in Q' to output of 'registers' entry
* Added a new entry 'flags'
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Convert macro definitions for flags bits to enum
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

When checking for command completions if the register value is zero, proceed
to next register.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Fix to support more than one sector in exec_drive_command().
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

'cmd_issue_lock' is for only acquiring a free slot, and it is not used
in interrupt context. So replaced irq version with non-irq version of spinlock.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Set the following block queue boundary variables
	* max_hw_sectors
	* max_segment_size
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>

Removed setting of q->nr_requests.
Signed-off-by: NJens Axboe <axboe@kernel.dk>

If a PIO (IOCTL/internal) command resulted in TFE, signal the wait event or break out of polling.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

For the ioctl command HDIO_GET_IDENTITY, return the stored copy of IDENTIFY
DATA instead of sending the command to the device - similar to libata.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This change sets custom timeouts depending on PIO command.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Fix clearing an incorrect register in mtip_init_port
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Release the semaphore in an error path in mtip_hw_get_scatterlist(). This
fixes the smatch warning inconsistent returns.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This removes the HOTPLUG_PCI_PCIE dependency on the driver and makes it
depend on PCI.

Cc: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Dump tagmap on failure, instead of individual tags.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

* If a ncq  command time out and a non-ncq command is active, skip restart port
* Queue(pause) ncq commands during operations spanning more than one non-ncq commands - secure erase, download microcode
* When a non-ncq command is active, allow incoming non-ncq commands to wait instead of failing back
* Changed timeout for download microcode and smart commands
* If the device in write protect mode, fail all writes (do not send to device)
* Set maximum retries to 2
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Shortened macros used to represent mtip_port->flags and dd->dd_flag
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

* Handle the interrupt completion of polled internal commands
* Do not check remove pending flag for standby command
* On rebuild failure,
    - set corresponding bit dd_flag
    - do not send standby command
* Free ida index in remove path
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

* Add support for detecting the following device status
        - write protect
        - over temp (thermal shutdown)
* Add new sysfs entry 'status', possible values - online, write_protect, thermal_shutdown
* Add new file 'sysfs-block-rssd' to document ABI (Reported-by: Greg Kroah-Hartman)
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Moved setting completion time into mtip_issue_ncq_command()
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

* Merged the following flags into one variable 'dd_flag':
        * drv_cleanup_done
        * resumeflag
* Added the following flags into 'dd_flag'
        * remove pending
        * init done
* Removed 'ftlrebuildflag' (similar flag is already part of mti_port->flags)
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Ensure that block device is properly unregistered, if
pci_register_driver() fails.
Signed-off-by: NRyosuke Saito <raitosyo@gmail.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()

This patch includes two changes:
	* fix incorrect value set for drv_cleanup_done
	* re-initialize and start port in mtip_restart_port()
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NSam Bradshaw <sbradshaw@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>