This fixes this rant from sparse:

  CHECK   drivers/net/wireless/ath/ath9k/xmit.c
drivers/net/wireless/ath/ath9k/xmit.c:107:13: warning: context imbalance in 'ath_txq_lock' - wrong count at exit
drivers/net/wireless/ath/ath9k/xmit.c:112:13: warning: context imbalance in 'ath_txq_unlock' - unexpected unlock
drivers/net/wireless/ath/ath9k/xmit.c:123:30: warning: context imbalance in 'ath_txq_unlock_complete' - unexpected unlock
  CC [M]  drivers/net/wireless/ath/ath9k/xmit.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes these sparse warnings:

  CHECK   drivers/net/wireless/ath/ath9k/ar9003_rtt.c
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:36:6: warning: symbol 'ar9003_hw_rtt_enable' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:41:6: warning: symbol 'ar9003_hw_rtt_disable' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:46:6: warning: symbol 'ar9003_hw_rtt_set_mask' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:52:6: warning: symbol 'ar9003_hw_rtt_force_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:102:6: warning: symbol 'ar9003_hw_rtt_load_hist' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:135:6: warning: symbol 'ar9003_hw_rtt_fill_hist' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:143:6: warning: symbol 'ar9003_hw_rtt_clear_hist' was not declared. Should it be stati
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Joe changed ath_dbg() to simpify code but while his patch was
being merged dfs.c was born and as such did not get the change
Joe envisioned. This fixes that. Test compiled with:

 make allmodconfig

Cc: Joe Perches <joe@perches.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: John W. Linville <linville@tuxdriver.com>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DFS_DEBUG_H is very generic, instead use something more specific
to ath9k such as ATH9K_DFS_DEBUG_H.
Reported-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: simplify tx locking" introduced a soft lockup triggered
by mac80211 sending a BAR frame triggered by a driver call to
ieee80211_tx_send_bar or ieee80211_tx_status.
Fix these issues by queueing processed tx status skbs and submitting them
to mac80211 outside of the lock.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.

This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.

On MIPS this reduces the total size for the modules by about 20k.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.

Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

its not used anywhere in the current code
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

before concluding that the recieved beacon is for us, let us make sure
that the BSSID is non-zero. when I configured ad-hoc mode as creator and
left it for some time without joining I found we recieved few frames whose
BSSID is zero, which we concluded wrongly as 'my_beacons'
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This initial DFS module provides basic functionality to deal
with radar pulses reported by the Atheros DFS HW pulse detector.

The reported data is evaluated and basic plausibility checks
are performed to filter false pulses. Passing radar pulses are
forwarded to pattern detectors which are not yet implemented.

(Some modifications to actually use ATH9K_DFS_DEBUGFS based on comments
from Julian Calaby <julian.calaby@gmail.com>. -- JWL)
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to enable DFS upstream we want to be sure
DFS has been tested for each chipset. Push for public
documentation of the requirements we want in place and
allow for enabling each chipset through a single upstream
commit.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The receiver will discard them anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of releasing and taking back the lock over and over again in the
tx path, hold the lock a bit longer, requiring much fewer lock/unlock pairs.
This makes locking much easier to review and should not have any noticeable
performance/latency impact.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tid->seq_next is initialized on A-MPDU start anyway, and the comment next
to this chunk of code seems to be bogus as well.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When processing A-MPDU tx status, only send a BAR for the failed packet
with the highest sequence number.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of limiting a subframe to 10 A-MPDU software transmission attempts,
count hardware retransmissions as well and raise the limit a bit. That way
there will be fewer software retransmission attempts when traffic suffers
from lots of hardware retransmissions.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the regulatory got updated by country IE for the world
roaming cards, need to reconfigure the tx power immediately to
increase the power level.
Reviewed-by: NSam Leffler <sleffler@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

in my previous patches of handling MCI interrupt I overlooked
the case of interrupt status/mask variable being zeroed out in
the below code, so ath_isr does not cache the MCI interrupt
in the intrstatus. finally MCI interrupt handling won't be
handled in ath9k_tasklet for the scheduled interrupts.
Fix this by moving the MCI interrupt code in the appropriate
position in ar9003_hw_get_isr

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

in ar9003_hw_get_isr we bail out if we don't have any primary
interrupts and synchronous interrupts, also make sure we don't
have any asynchronous interrupts
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The stations always chooses 1Mbps for all trasmitting frames,
whenever the AP is configured to lock the supported rates.
As the max phy rate is always set with the 4th from highest phy rate,
this assumption might be wrong if we have less than that. Fix that.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Reported-by: NAjay Gummalla <agummalla@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  Enable ANI for ar9100 since it seems to be working fine (and as a
matter of fact ANI was always performed for ar9100 since code which
was supposed to disable it didn't achieve this goal).
  This patch sets config.enable_ani to default (true) value for
ar9100.
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  Currently in ath9k code there is an attempt which is meant to
disable ANI for ar9100 and ar9340. But it doesn't really achieve
this. All it does is disable ANI init and setup (i.e. calls to
ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is
not called ah->config.ani_poll_interval is never initialized (i.e. it
is always zero) and ath_ani_calibrate always executes ANI procedures
(over uninitialized ANI parameters).
  Moreover, ath_ani_calibrate is being called each 1ms because
common->ani.timer is set to zero interval because
ah->config.ani_poll_interval==0 (and thus smallest value of all
intervals). Normally it should not be called this often.
  This patch changes the code so config.enable_ani is used to check if
ANI should be performed.
  config.enable_ani is initialized to true by default. This patch sets
it to false for ar9100 and ar9340.
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  To help debugging write a log entry when long calibration, short
calibration or ANI is performed.
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  Add missed space and change typo in calibration debugging log.
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recently more places in mac80211 call drv_flush to ensure proper order
for state changes wrt. powersave, channel changes, etc. On some systems
such calls lead to spurious logspam about failing to stop tx dma, as well
as hardware resets that go along with that.
Instead of dropping packets in a place where it's completely unnecessary,
only do it when drop == true.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Turning off the radio when mac80211 tells the driver that it's idle is not
a good idea, as idle interfaces might still occasionally scan or send packets.
The only time the radio can be safely turned off is when drv_stop has been
called. In the mean time, use sc->ps_idle only to indicate network sleep vs
full sleep.
Move the LED GPIO changes out of the PCI suspend/resume path, the start/stop
functions already take care of that.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After waking up from full sleep, registers are accessible, but rx/tx
typically fails. A fast channel change will not recover from this, so
ensure that a full-sleep -> wake transition is always followed by a full
reset.

The reason why this hasn't created any serious problems yet is that it's
hidden by the (wrong) behavior of enabling/disabling the radio when the
wiphy idle state changes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

max_streams for AR9462 is '2'. it does not fixes anything, but
improves the code readability
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

based on systems change to improve rx dynamic range,
and enables heavy clip for 5G HT40 MCS0 to improve
spectral mask power. also remove an unused function
declaration

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

fixes a regression on single-stream chips introduced in
commit 43c35284
"ath9k: implement .get_antenna and .set_antenna"
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the default tx/rx chainmask for AR9462 is 0x3.
this patch helps to assign 0x3 rather than 0x7 for
AR9462 with the help of fix_chainmask module if something
goes wrong in reading tx/rx chain mask from OTP/EEPROM
card(though its very unlikely)
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

only for AR9485 (or) later chipsets TxIQ calibration
runs as part of AGC calibration. without this patch
TX IQ cal completion i.e. ar9003_hw_tx_iq_cal_run won't be executed
for AR9003
Reviewed-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

here we check for BT state and if BT calibration has started,
give 25ms for BT Calibration to finish. we also take care of 2G/5G
switch and LNA transfer incase WLAN is operating in 5G. in case the BT
state is awake when we do WLAN calibration re-calibrate and we reset
the message exchange between WLAN and BT. BT is given preference when
simultaneous CAL request happens. calibration for WLAN/BT is done
assuming that the other co-existing module is in awake state, if not
we continue to do calibration while if the other module's state changes
we need to do restart the calibration handshake

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>