I checked ext2_ioctl and could not find anything in there that would need the
BKL.  So convert it over to use unlocked_ioctl
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a new block bitmap is read from disk in read_block_bitmap() there are a
few bits that should ALWAYS be set.  In particular, the blocks given
corresponding to block bitmap, inode bitmap and inode tables.  Validate the
block bitmap against these blocks.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a new block bitmap is read from disk in read_block_bitmap() there are a
few bits that should ALWAYS be set.  In particular, the blocks given
corresponding to block bitmap, inode bitmap and inode tables.  Validate the
block bitmap against these blocks.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some Supermicro BIOSes describe a SATA PCI BAR as a motherboard resource.
The PNP system driver claims motherboard resources, and this prevents the
sata_nv driver from requesting it later.

This patch disables the PNP0C01/PNP0C02 resources so they won't be claimed
by the PNP system driver, so they'll available for sata_nv.

This fixes the bugs below, where sata_nv detects only two out of four SATA
drives.  The signature includes dmesg lines similar to these:

  pnp: 00:09: iomem range 0xdfefc000-0xdfefcfff has been reserved
  pnp: 00:09: iomem range 0xdfefd000-0xdfefd3ff has been reserved
  pnp: 00:09: iomem range 0xdfefe000-0xdfefe3ff has been reserved

  PCI: Unable to reserve mem region #6:1000@dfefd000 for device 0000:80:07.0
  sata_nv: probe of 0000:80:07.0 failed with error -16
  PCI: Unable to reserve mem region #6:1000@dfefe000 for device 0000:80:08.0
  sata_nv: probe of 0000:80:08.0 failed with error -16

References:
    https://bugzilla.redhat.com/show_bug.cgi?id=280641
    https://bugzilla.redhat.com/show_bug.cgi?id=313491
    http://lkml.org/lkml/2008/1/9/449
    http://thread.gmane.org/gmane.linux.acpi.devel/27312

This is post-2.6.24 material.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The PNP_DRIVER_RES_DO_NOT_CHANGE flag is meant to signify that the PNP core
should not change resources for the device -- not that it shouldn't
disable/enable the device on suspend/resume.

ALSA ISAPnP drivers set PNP_DRIVER_RES_DO_NOT_CHANAGE (0x0001) through
setting PNP_DRIVER_RES_DISABLE (0x0003).  The latter including the former
may in itself be considered rather unexpected but doesn't change that
suspend/resume wouldn't seem to have any business testing the flag.

As reported by Ondrej Zary for snd-cs4236, ALSA driven ISAPnP cards don't
survive swsusp hibernation with the resume skipping setting the resources
due to testing the flag -- the same test in the suspend path isn't enough
to keep hibernation from disabling the card it seems.

These tests were added (in 2005) by Piere Ossman in commit
68094e32, "alsa: Improved PnP suspend
support" who doesn't remember why.  This deletes them.
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Changed the isapnp semaphore to a mutex.

[akpm@linux-foundation.org: no externs-in-c]
[akpm@linux-foundation.org: build fix]
Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are three kind of parse functions provided by PNP acpi/bios:
 - get current resources
 - set resources
 - get possible resources
The first two may be needed later at runtime.
The possible resource settings should never change dynamically.
And even if this would make any sense (I doubt it), the current implementation
only parses possible resource settings at early init time:
  -> declare all the option parsing __init

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NThomas Renninger <trenn@suse.de>
Acked-By: NRene Herman <rene.herman@gmail.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make pnp_activate_dev() and pnp_disable_dev() return only 0 (success) or a
negative error value, as pci_enable_device() and pci_disable_device() do.

Previously they returned:

    0:	device was already active (or disabled)
    1:	we just activated (or disabled) device
    <0:	-EBUSY or error from pnp_start_dev() (or pnp_stop_dev())

Now we return only 0 (device is active or disabled) or <0 (error).

All in-tree callers either ignore the return values or check only for
errors (negative values).
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

raid5's 'make_request' function calls generic_make_request on underlying
devices and if we run out of stripe heads, it could end up waiting for one of
those requests to complete.  This is bad as recursive calls to
generic_make_request go on a queue and are not even attempted until
make_request completes.

So: don't make any generic_make_request calls in raid5 make_request until all
waiting has been done.  We do this by simply setting STRIPE_HANDLE instead of
calling handle_stripe().

If we need more stripe_heads, raid5d will get called to process the pending
stripe_heads which will call generic_make_request from a

This change by itself causes a performance hit.  So add a change so that
raid5_activate_delayed is only called at unplug time, never in raid5.  This
seems to bring back the performance numbers.  Calling it in raid5d was
sometimes too soon...

Neil said:

  How about we queue it for 2.6.25-rc1 and then about when -rc2 comes out,
  we queue it for 2.6.24.y?
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Tested-by: Ndean gaudet <dean@arctic.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Finish ITERATE_ to for_each conversion.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As this is more in line with common practice in the kernel.  Also swap the
args around to be more like list_for_each.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As this is more consistent with kernel style.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As suggested by Andrew Morton.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Due to possible deadlock issues we need to use a schedule work to kobject_del
an 'rdev' object from a different thread.

A recent change means that kobject_add no longer gets a refernce, and
kobject_del doesn't put a reference.  Consequently, we need to explicitly hold
a reference to ensure that the last reference isn't dropped before the
scheduled work get a chance to call kobject_del.

Also, rename delayed_delete to md_delayed_delete to that it is more obvious in
a stack trace which code is to blame.

Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, a given device is "claimed" by a particular array so that it cannot
be used by other arrays.

This is not ideal for DDF and other metadata schemes which have their own
partitioning concept.

So for externally managed metadata, just claim the device for md in general,
require that "offset" and "size" are set properly for each device, and make
sure that if a device is included in different arrays then the active sections
do not overlap.

This involves adding another flag to the rdev which makes it awkward to set
"->flags = 0" to clear certain flags.  So now clear flags explicitly by name
when we want to clear things.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If you try to start an array for which the number of raid disks is listed as
zero, md will currently try to read metadata off any devices that have been
given.  This was done because the value of raid_disks is used to signal
whether array details have been provided by userspace (raid_disks > 0) or must
be read from the devices (raid_disks == 0).

However for an array without persistent metadata (or with externally managed
metadata) this is the wrong thing to do.  So we add a test in do_md_run to
give an error if raid_disks is zero for non-persistent arrays.

This requires that mddev->persistent is set corrently at this point, which it
currently isn't for in-kernel autodetected arrays.

So set ->persistent for autodetect arrays, and remove the settign in
super_*_validate which is now redundant.

Also clear ->persistent when stopping an array so it is consistently zero when
starting an array.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.

Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a device fails, we must not allow an further writes to the array until
the device failure has been recorded in array metadata.  When metadata is
managed externally, this requires some synchronisation...

Allow/require userspace to explicitly remove failed devices from active
service in the array by writing 'none' to the 'slot' attribute.  If this
reduces the number of failed devices to 0, the write block will automatically
be lowered.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Add a state flag 'external' to indicate that the metadata is managed
  externally (by user-space) so important changes need to be
  left of user-space to handle.
  Alternates are non-persistant ('none') where there is no stable metadata -
  after the  array is stopped there is no record of it's status - and
  internal which can be version 0.90 or version 1.x
  These are selected by writing to the 'metadata' attribute.

- move the updating of superblocks (sync_sbs) to after we have checked if
  there are any superblocks or not.

- New array state 'write_pending'.  This means that the metadata records
  the array as 'clean', but a write has been requested, so the metadata has
  to be updated to record a 'dirty' array before the write can continue.
  This change is reported to md by writing 'active' to the array_state
  attribute.

- tidy up marking of sb_dirty:
   - don't set sb_dirty when resync finishes as md_check_recovery
     calls md_update_sb when the sync thread finishes anyway.
   - Don't set sb_dirty in multipath_run as the array might not be dirty.
   - don't mark superblock dirty when switching to 'clean' if there
     is no internal superblock (if external, userspace can choose to
     update the superblock whenever it chooses to).
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently an md array with a write-intent bitmap does not updated that bitmap
to reflect successful partial resync.  Rather the entire bitmap is updated
when the resync completes.

This is because there is no guarentee that resync requests will complete in
order, and tracking each request individually is unnecessarily burdensome.

However there is value in regularly updating the bitmap, so add code to
periodically pause while all pending sync requests complete, then update the
bitmap.  Doing this only every few seconds (the same as the bitmap update
time) does not notciably affect resync performance.

[snitzer@gmail.com: export bitmap_cond_end_sync]
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: "Mike Snitzer" <snitzer@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Clean up the coding style in raid6test/test.c.  Break it apart into
subfunctions to make the code more readable.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make both mktables.c and its output CodingStyle compliant.  Update the
copyright notice.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NOliver Pinter <oliver.pntr@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current attr_fgcol_ec / attr_bgcol_ec macros do a simple shift of bits
to get the color from vc_video_erase_char.  For a monochrome display
however the attribute does not contain any color, only attribute bits.
Furthermore the reverse bit is lost because it is shifted out, the
resulting color is always 0.

This can bee seen on a monochrome console either directly or by setting it
to inverse mode via "setterm -inversescreen on" .  Text is written with
correct color, fb_fillrects from a bit_clear / bit_clear_margins will get
wrong colors.
Signed-off-by: NThomas Pfaff <tpfaff@pcs.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ensure that the default display parameter passed in via the
device's platform data is valid. It turns out when mach-bast.c
was updated, the default_display was set outside of the display
array bounds, causing a panic on startup.

If the default_display is bigger than num_displays, then generate
an error and refuse to initialise the driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change the initial pattern in the s3c2410 framebuffer driver
to black.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update the debugging in the s3c2410 framebuffer driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the S3C2412 to the S3C2410 frame buffer driver
by ensuring that any moved registers can be dealt with.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the console suspend to before we save the state of
the framebuffer to ensure that it does not try and change
the fb state again once we have copied it out.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix garbled letters on big endian machines with acceleration enabled.

This makes pm2fb works fine with full acceleration on sparc machine (card
known as Sun PGX-32 or TechSource Raptor GFX-8P).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix modedb typos
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

cleanup sweep:
  - Kill ps3fb_priv.xdr_ea and ps3fb_priv.xdr_size, use info->screen_base and
    info->fix.smem_len instead.
  - Kill superfluous assignments to info->fix.smem_start, info->fix.smem_len,
    and info->screen_base in ps3fb_set_par(). Their values never change.
  - Add sparse annotations to casts to kill address space warnings
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Round up arbitrary video modes until they fit (if possible)
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reorganize modedb handling:
  - Reorder the video modes in ps3fb_modedb, for easier indexing using
    PS3AV_MODE_* numbers,
  - Introduce ps3fb_native_vmode(), to convert from native (PS3AV_MODE_*) mode
    numbers to struct fb_videomode *,
  - Rename and move ps3fb_default_mode() to ps3fb_vmode().
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow all video modes where the visible resolution plus the black borders
matches a native resolution
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Frame buffer offsets don't have to be `unsigned long', `unsigned int' is
sufficient
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kill ps3fb_res[], as all information it contains can be obtained in some other
way.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Open-code the X_OFF(), Y_OFF(), WIDTH(), HEIGHT(), and VP_OFF() macros, as
they're used in one place only
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>