Since all devices share the same operation here,
there's no need to call it indirectly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The set_pwr_src operation is only ever used from
within the same sub-driver that it is declared
in, so it can just be called directly instead of
being an operation. Also, it is never called to
set the power source to V_aux, so change the two
functions accordingly (but keep the V_aux code
for documentation purposes in a comment).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This operation is only ever called from set_hw_params,
which is also already based on the config/ops, so that
there's no need to have a separate set_ct_kill op and
we can just call the right ct_threshold function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_dump_fh function is only used
by the agn module, so it can be there
instead of being exported by the core.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_dump_csr function is only used
within the agn module, so it can be
moved there instead of being exported
by the core.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_toggle_tx_ant function is only used
by agn code, so it can be moved into the
agn module instead of being exported from
the core.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Code and data related to agn bitrates can be
part of the agn module rather than being in
the core module.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

A number of exports, especially related to
thermal throttling, are unnecessary because
the code lives in the same module that it
is used in, so remove them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The code to print out TX failure reasons is
AGN specific, so it can be in the AGN module.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

By duplicating a little bit of code between 3945
and agn, we can move a lot of code into an agn
specific station management file and thus reduce
the amount of code in core that is dead to 3945.

before:
   text	   data	    bss	    dec	    hex	filename
 212886	   3872	     96	 216854	  34f16	iwlcore.ko
 620542	  10448	    304	 631294	  9a1fe	iwlagn.ko
 314013	   3264	    196	 317473	  4d821	iwl3945.ko

after:
   text	   data	    bss	    dec	    hex	filename
 202857	   3872	     92	 206821	  327e5	iwlcore.ko
 629102	  10448	    308	 639858	  9c372	iwlagn.ko
 314240	   3264	    196	 317700	  4d904	iwl3945.ko

delta:
 -10029   iwlcore.ko
   8560   iwlagn.ko
    227   iwl3945.ko

so it's a net win even if you have both loaded,
likely because a lot of EXPORT_SYMBOLs go away.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

All drivers share the same implementation, so
there's no need to call this via a function
pointer nor to export it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Rename iwl_mac_beacon_update to iwlcore_beacon_update
and make the calling convention a bit different. The
old name with _mac_ indicated that it was a mac80211
callback, but that's no longer true.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The core module doesn't need to carry around
the code for chain settings that is used for
HT drivers (agn) only.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There's no need to go via the indirect function
call from within the 3945 subdriver.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The different drivers need to do different things
after a scan, so create a post_scan hook to allow
them to do this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwl_commit_rxon really should be named
iwlagn_commit_rxon, so rename it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The following commit removed DISABLE_REGWRITE_BUFFER ops. The unnecessary
REGWRITE_BUFFER_FLUSH was not removed properly which is causing failure on
hw reset.

Author: Felix Fietkau <nbd@openwrt.org>
Date:   Tue Oct 5 12:03:42 2010 +0200

    ath9k_hw: clean up register write buffering
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the NVS/INI-parameters for the driver/firmware there is the FEM
(front end module) selection option, which may configure the hardware FEM
via autodetection or manual selection. So far, there has been support for
manual selection only.

Add support for FEM autodetection.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 030725d2.

This commit relies on commit 5ed3bc72
("mac80211: use netif_receive_skb in ieee80211_tx_status callpath")
Unfortunately not all drivers are calling ieee80211_tx_status from a
compatible context, so that commit needs to be reverted in 2.6.36.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding MODULE_FIRMWARE define for 130 series of devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

130 series device should use firmware name with 130 in it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This reverts commit 7acc7c68. It was
applied to avoid possible warning in ieee80211_restart_hw, however
reason of the warning were races in mac80211, currently hopefully fixed.

Not reseting device when performing scan is bad for two reasons.

When forcing reset from iwl_check_stuck_queue(), in case of fail,
reset will be repeated until scan finish. But since firmware is in bad
shape, scan only finish after scan_check work (about 7s). So we will
delay the reset, what is not good behaviour.

When forcing reset from iwl_recover_from_statistics(), we will not
repeat the reset, so we will not perform reset at all when needed.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's already set in PHY common code.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drv_config callback is called only after the ack for the nullframe
is received and so driver need not do anything special for this.

So remove NULLFUNC_COMPLETED, PS_ENABLED flags and bf_isnullfunc
flags from ath9k as mac80211 already handles them properly.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After the last rounds of cleanup, these functions are now functionally
equivalent and can thus be merged.
Also get rid of some excessive (and redundant) debug messages.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code gets more concise and readable when making the new ANI functions
fall back to the old ones if ANI v2 is disabled. This also makes further code
cleanup easier.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse
it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old
and ath9k_hw_proc_mib_event_new).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ANI state is kept per channel, so instead of keeping an array of ANI states
with an arbitrary size of 255, move the ANI state into the channel struct.

Move some config settings that are not per-channel out of
the per-channel struct to save some memory.

With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can
be merged into a single function.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after
REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that
makes keeping those ops separate rather pointless, as it only increases
code size and line number counts.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The cycle counters are used by ANI to determine the amount of time that the
radio spent not receiving or transmitting. They're also used for debugging
purposes if the baseband watchdog on AR9003 detects a lockup.
In the future, we want to use these counters to determine the medium utilization
and export this information via survey. For that, we need to make sure that
the counter is only accessed from one place, which also ensures that
wraparounds won't occur at inconvenient points in time.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calibration actual calibration flags are only used by the per chip family
source files, so it makes more sense to define them in those files instead
of globally. That way the code has to test for less flags.

Also instead of using a separate callback for testing whether a particular
calibration type is supported, simply adjust ah->supp_cals in the calibration
init which is called right after the hardware reset, before any of the
calibrations are run.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  wireless-testing
  commit 37e5bf65
  Author: Luis R. Rodriguez <lrodriguez@atheros.com>
  Date:   Sat Jun 12 00:33:40 2010 -0400

    ath9k_hw: fix clock rate calculations for ANI

This commit accidentally broke clock rate calculation by doubling the
calculated clock rate
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

add new structures and defines need to identify 130 devices.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwl5000_tx_resp really should be iwlagn_tx_resp, rename it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

some structure belong to _agn devices, not just 5000. Fix it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>