Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NStanley Miao <stanley.miao@windriver.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.

Cc: Hunyue Yau <hyau@mvista.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

board-omap3touchbook.c adds an LCD device, but the kernel doesn't
contain a driver for the device. So let's remove the unneeded LCD
device.

Cc: Gregoire Gentil <gregoire@gentil.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

RX51 uses the new DSS2 display driver, but the board file still
contained some code for the old omapfb driver. The old code can be
removed.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

An on-board projector named picodlp is available for OMAP4430 SDP.

Entry for this picodlp as a panel is being added in dss_devices array to
the board file.  It needs 4 GPIO pins for interfacing with host
processor and these are defined and two of them are configured in board
file.  Two GPIOs power_on and display_select are configured here.
picodlp also needs an i2c client over i2c controller-2 at address 0x1b.
Signed-off-by: NMayuresh Janorkar <mayur@ti.com>
Signed-off-by: NMythri P K <mythripk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

4430SDP has two Taal DSI panels, connected to DSI 1 and DSI 2 modules.
The panels use a common PWM backlight, which will be implemented later
when the PWM driver has been improved to support the backlight.

Until the PWM driver has been improved, the following hack added to
arch/arm/mach-omap2/board-4430sdp.c can be used to set the backlight to
max:

static int omap_4430sdp_hack_backlight(void)
{
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2OFF);
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2ON);
       twl_i2c_write_u8(TWL6030_MODULE_ID1, 0x30, TWL6030_TOGGLE3);
       return 0;
}
late_initcall(omap_4430sdp_hack_backlight);
Signed-off-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

4430SDP board file contains some unused old LCD configurations. They are
not used and can be removed.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add i2c bus number for DVI output for boards with DVI output where the
i2c bus has been confirmed to be connected and working. The driver uses
this to detect if a panel is connected and to read EDID.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP3 Stalker board has definitions for LCD, but uses the generic driver
without any information what kind of LCD it has. The board should use a
particular panel type from panel-generic-dpi driver, not the generic
one.

As I haven't gotten response the signer-off of stalker board about the
issue, this patch removes the LCD support from the board file. This will
allow us to clean up the panel-generic-dpi driver and make it support
only fixed size panels.

CC: Jason Lam <lzg@ema-tech.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Multiple OMAP3/4 boards have a DVI framer output. This patch makes the
boards use the new panel-dvi driver, instead of the panel-generic-dpi
driver.

Separate drivers for fixed size panels and DVI framer gives us cleaner
driver code.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.

Cc: Mythri P K <mythripk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Change lcd driver from generic to AT070TN83.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Implement dsi_mux_pads for OMAP4. On enable the function enables the DSI
pins and disables pull down. On disable the function disables the pins
and enables pull down.

It is unclear from the TRM whether the pull down is active if the pins
are disabled, so this implementation may leave the pins floating when
the DSI device is disabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP DSS normally gets power from VCXIO on OMAP4. Add configuration for
this into twl-common.c

Mark VCXIO as always_on, as VCXIO is used by multiple components,
including the MPU, and turning it off when DSS doesn't need it would
lead the device to halt.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.

Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a missing array terminator to omap2430_usbhsotg_addrs[].  Without
this terminator, the omap_hwmod resource building code runs off the
end of the array, resulting in at least this error -- if not worse
behavior:

[    0.578002] musb-omap2430: failed to claim resource 4
[    0.583465] omap_device: musb-omap2430: build failed (-16)
[    0.589294] Could not build omap_device for musb-omap2430 usb_otg_hs

This should have been part of commit
78183f3f ("omap_hwmod: use a null
structure record to terminate omap_hwmod_addr_space arrays") but was
evidently missed.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The oscillator that supplies GPT12_FCLK and WDT1_FCLK exists in the
WKUP powerdomain[1].  This resolves at least one boot-time warning:

omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.

1. _OMAP34xx Multimedia High Security (HS) Device Silicon Revision 3.1.x
   Security Addendum Version K (SWPU119K)_  Figure 3-29.  August 2010.

Fix the following compile warning:

arch/arm/mach-omap2/clock44xx_data.c: In function 'omap4xxx_clk_init':
arch/arm/mach-omap2/clock44xx_data.c:3371:6: warning: 'cpu_clkflg' may be used uninitialized in this function

The approach taken here is intended to work if omap4xxx_clk_init() is
converted into an initcall.

Thanks to Bjarne Steinsbo <bsteinsbo@gmail.com> for proposing another
approach.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Bjarne Steinsbo <bsteinsbo@gmail.com>

After commit 665d0013 ("OMAP2+: hwmod:
Follow the recommended PRCM module enable sequence"), device drivers
for OMAP IP blocks that do not use runtime PM can cause oopses or
kernel instability[1][2].

This is because those non-runtime PM drivers do not use the hwmod
code, which implements the correct IP block enable and disable
sequence.

Several options for dealing with this problem have been proposed:

1. Add a new field to the OMAP struct clk to mark clocks that are
   currently used by non-runtime PM drivers.  Modify the clock code to
   use the old clockdomain sequence for these marked clocks.  As
   drivers are converted to use runtime PM, remove the annotation from
   the clocks.

2. Similar to #1, but associate the flag with the struct omap_clk
   instead.

3. Add IDLEST wait support to the OMAP4 clock code, similar to the way
   it is implemented for OMAP2/3, and enable it in each struct clk
   currently used by non-runtime PM drivers.  As drivers are converted
   to use runtime PM, remove the annotation from the clocks.

4. Do nothing; leave the problem to those responsible for the
   unconverted drivers.

5. Re-enable clock-based clockdomain control in the OMAP4 clock code.
   This would revert back to the behavior of Linux 3.0, simply with a
   slightly longer module enable/disable latency.

Unfortunately, no approach seemed particularly good.  Options 1
through 3 seemed unwise due to the following reasons:

A. The OMAP struct clks are intended primarily to describe hardware
   clock nodes, and the intention is that no driver-specific data
   should be stored there (applies to #1)

B. The resulting patch would have been quite large for the -rc series
   (applies to #1, #2, #3)

C. The patch would have been a new, yet temporary hack; and similar fixes
   have drawn negative comments in the recent past (see for example [3])

Option 4 is undesirable because commit
665d0013 ("OMAP2+: hwmod: Follow the
recommended PRCM module enable sequence") has resulted in a less
stable kernel; and kernel stability is more important than OMAP4 power
management.

Option 5 is the approach taken in this patch.  This seemed to be the
least intrusive approach for 3.1-rc.

The approach in this patch was originally proposed by Ohad Ben-Cohen
<ohad@wizery.com>.  I'm simply writing the commit message and passing
it along.

...

Thanks to Luciano Coelho <coelho@ti.com> for reporting the problem.
Thanks to Ohad Ben-Cohen <ohad@wizery.com> for tracking the problem
down, generating a temporary workaround, and proposing a patch to deal
with the problem.  Thanks to Rajendra Nayak <rnayak@ti.com> for
proposing another patch to deal with the problem.  Thanks to Felipe
Balbi <balbi@ti.com> for comments.

1. Coelho, Luciano <coelho@ti.com>.  _Re: Oops on ehci_hcd when
   booting 3.0.0-rc2 on panda_.  Tue, 09 Aug 2011 14:26:08 +0300.
   Posted to the <linux-omap@vger.kernel.org> mailing list.  Available
   from (among others)
   http://www.spinics.net/linux/lists/linux-omap/msg55213.html

2. Munegowda, Keshava <keshava_mgowda@ti.com>. _Re: Oops on ehci_hcd
   when booting 3.0.0-rc2 on panda_.  Thu, 11 Aug 2011 13:51:05 +0530.
   Posted to the <linux-omap@vger.kernel.org> mailing list.  Available
   from (among others)
   http://www.spinics.net/linux/lists/linux-omap/msg55371.html

3. King, Russell <linux@arm.linux.org.uk>.  _Re: [PATCH 5/8] OMAP4:
   PM: TEMP: Prevent l3init from idling/force sleep_.  Thu, 23 Jun
   2011 16:22:49 +0100.  Posted to the <linux-omap@vger.kernel.org>
   mailing list.  Available from (among others)
   http://www.mail-archive.com/linux-omap@vger.kernel.org/msg51392.htmlSigned-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Luciano Coelho <coelho@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

While using clockdomain force wakeup method, not waiting for powerdomain
to be effectively ON may end up locking the clockdomain FSM until a
next wakeup event occurs.

One such issue was seen on OMAP4430, where L4_PER was periodically
getting stuck in in-transition state when transitioning from from OSWR to ON.

This issue was reported and investigated by Patrick Titiano <p-titiano@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Reported-by: NPatrick Titiano <p-titiano@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated to apply; added transition wait on clkdm_deny_idle();
 remove two superfluous pwrdm_wait_transition() calls]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Program all powerdomain target state as ON; this is to prevent domains
from hitting low power states (if bootloader has target states set to
something other than ON) and potentially even losing context while PM
is not fully initialized, which can cause the system to crash.  The PM
late init code can then program the desired target state for all the
power domains.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: dropped comment typo hunk; fixed comment indent and moved
 to kerneldoc; moved code to pwrdm_init(); changed pwrdm_init() argument name
 to prevent clash; cleaned up patch description]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

If CONFIG_OMAP_32K_TIMER is not selected and dmtimer is used as clocksource, the
timer stops counting once overflow occurs as it was not set in autoreload mode.
This results into timekeeping failure: for example, 'sleep 1' at the shell after
the timer counter overflow would hang.

This patch sets up autoreload when starting the clocksource timer which fixes
the above issue.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since 7203f8a4 (arm: mach-omap2: remove
NULL board_mux from board files) NULL board_mux is defined in mux.h.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use kstrdup rather than duplicating its implementation

The semantic patch that makes this output is available
in scripts/coccinelle/api/kstrdup.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: NThomas Meyer <thomas@m3y3r.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Builds for multi-OMAP2 (e.g., OMAP2420 with OMAP2430) with
CONFIG_ARCH_OMAP4=n fail with the following errors:

arch/arm/mach-omap2/built-in.o: In function `_enable_module':
arch/arm/mach-omap2/omap_hwmod.c:701: undefined reference to `omap4_cminst_module_enable'
arch/arm/mach-omap2/built-in.o: In function `_disable_module':
arch/arm/mach-omap2/omap_hwmod.c:726: undefined reference to `omap4_cminst_module_disable'
arch/arm/mach-omap2/built-in.o: In function `_wait_target_disable':
arch/arm/mach-omap2/omap_hwmod.c:1179: undefined reference to `omap4_cminst_wait_module_idle'

This is probably due to the preprocessor directives in
arch/arm/plat-omap/include/plat/cpu.h that convert some cpu_is_omap*()
expressions from preprocessor directives into something that is only
resolvable during runtime, if multiple OMAP2 build targets are
selected.

Thanks to Tony Lindgren <tony@atomide.com> for reporting.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit b22f954b (OMAP4: Move common twl6030 configuration to twl-common)
caused compile failures for code for OMAP arch which is not selected by
the config.

Fixes issues like:
With CONFIG_ARCH_OMAP3=y and CONFIG_ARCH_OMAP4=n, I'm getting this:

arch/arm/mach-omap2/built-in.o:(.data+0xf99c): undefined reference to `omap4430_phy_init'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a0): undefined reference to `omap4430_phy_exit'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a4): undefined reference to `omap4430_phy_power'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a8): undefined reference to `omap4430_phy_set_clk'
arch/arm/mach-omap2/built-in.o:(.data+0xf9ac): undefined reference to `omap4430_phy_suspend'

Fix the problem by moving the code to ifdef sections for omap3 and omap4.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap_sr_disable_reset_volt is called with irqs off in omapx_enter_sleep,
as part of idle sequence, this eventually calls sr_disable and
pm_runtime_put_sync. pm_runtime_put_sync calls rpm_idle, which will
enable interrupts in order to call the callback. In this short interval
when interrupts are enabled, scenarios such as the following can occur:
while interrupts are enabled, the timer interrupt that is supposed to
wake the device out of idle occurs and is acked, so when the CPU finally
goes to off, the timer is already gone, missing a wakeup event.

Further, as the documentation for runtime states:"
 However, subsystems can use the pm_runtime_irq_safe() helper function
 to tell the PM core that a device's ->runtime_suspend() and ->runtime_resume()
 callbacks should be invoked in atomic context with interrupts disabled
 (->runtime_idle() is still invoked the default way)."

Hence, replace pm_runtime_put_sync with pm_runtime_put_sync_suspend
to invoke the suspend handler and shut off the fclk for SmartReflex
module instead of using the idle handler in interrupt disabled context.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NColin Cross <ccross@google.com>
[khilman@ti.com: minor Subject edits]
Signed-off-by: NKevin Hilman <khilman@ti.com>

Board code should not touch omap_device internals.  To get the MPU/IVA devices,
use existing APIs: omap2_get_mpu_device(), omap2_get_iva_device().
Signed-off-by: NKevin Hilman <khilman@ti.com>

SmartReflex should be disabled while entering low power mode due to
a) SmartReflex values are not defined for retention voltage, further
b) with SmartReflex enabled, if CPU enters lower c-states, FSM will try
to bump the voltage to current OPP's voltage for which it has entered c-state;
hence SmartReflex needs to be disabled for MPU, CORE and IVA voltage
domains in idle path before enabling auto retention voltage achievement
on the device.

However, since the current pm_runtime setup for SmartReflex devices are
setup to allow callbacks to be invoked with interrupts enabled, calling
SmartReflex enable/disable from other contexts such as idle paths
where preemption is disabled causes warnings such as the following
indicating of a potential race.
[   82.023895] [<c04d079c>] (__irq_svc+0x3c/0x120) from [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c)
[   82.023895] [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c) from [<c0323234>] (rpm_callback+0x4c/0x68)
[   82.023956] [<c0323234>] (rpm_callback+0x4c/0x68) from [<c0323f7c>] (rpm_resume+0x338/0x53c)
[   82.023956] [<c0323f7c>] (rpm_resume+0x338/0x53c) from [<c03243f4>] (__pm_runtime_resume+0x48/0x60)
[   82.023986] [<c03243f4>] (__pm_runtime_resume+0x48/0x60) from [<c008aee0>] (sr_enable+0xa8/0x19c)
[   82.023986] [<c008aee0>] (sr_enable+0xa8/0x19c) from [<c008b2fc>] (omap_sr_enable+0x50/0x90)
[   82.024017] [<c008b2fc>] (omap_sr_enable+0x50/0x90) from [<c00888c0>] (omap4_enter_sleep+0x138/0x168)

Instead, we use pm_runtime_irq_safe to tell the PM core that callbacks can be
invoked in interrupt disabled contexts.
Acked-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: NKevin Hilman <khilman@ti.com>

CONFIG_PM is no longer a user-selectable Kconfig option.  Rather it is
automatically enabled if either CONFIG_SUSPEND or CONFIG_RUNTIME_PM is
enabled, so having a 'select PM' here is redunant when 'select
CONFIG_PM_RUNTIME' is present.
Signed-off-by: NKevin Hilman <khilman@ti.com>

The RX-51 uses the CSIb IO complex for camera operation. The
board file is missing definition for the regulator supplying
the CSIb complex, so this is added for better power
management.
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

oh_core variable is no longer used, so it and its initialization can be
removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

opt_clock_available() is no longer needed, so remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Initialize get_context_loss_count in the DSS board data to
omap_pm_get_dev_context_loss_count, so that omapdss driver can use it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The function to get device's context loss count has changed from

omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()

Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.

Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now most of ARM machines has the alsmot same __clk_get/put() macro

So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files

But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config

Now there are only 3 caese.

1) define the clk structure with clkdev macro => Need to move clk structure to proper header file

arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h

2) export the __clk_get/put function at clock.c

arch/arm/mach-shmobile/include/mach/clkdev.h

3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

Until these drivers are runtime PM converted, their device power
states are managed by calling custom driver hooks late in the
idle/suspend path.  Therefore, do not let the suspend/resume core code
automatically idle these devices since they will be managed manually
by the OMAP PM core very late in the idle/suspend path.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

On OMAP4, the PRCM recommended sequence for enabling
a module after power-on-reset is:
-1- Force clkdm to SW_WKUP
-2- Enabling the clocks
-3- Configure desired module mode to "enable" or "auto"
-4- Wait for the desired module idle status to be FUNC
-5- Program clkdm in HW_AUTO(if supported)

This sequence applies to all older OMAPs' as well,
however since they use autodeps, it makes sure that
no clkdm is in IDLE, and hence not requiring a force
SW_WKUP when a module is being enabled.

OMAP4 does not need to support autodeps, because
of the dyanamic dependency feature, wherein
the HW takes care of waking up a clockdomain from
idle and hence the module, whenever an interconnect
access happens to the given module.

Implementing the sequence for OMAP4 requires
the clockdomain handling that is currently done in
clock framework to be done as part of hwmod framework
since the step -4- above to "Wait for the desired
module idle status to be FUNC" is done as part of
hwmod framework.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[b-cousson@ti.com: Adapt it to the new clkdm hwmod attribute and API]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: dropped mach-omap2/clock.c changes; modified to only
 call the clockdomain code if oh->clkdm is set; disable clock->clockdomain
 interaction on OMAP4]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The OMAP2/3 clock code was written to notify the clockdomain code when
the first clock in a clockdomain is enabled and when the last enabled
clock in a clockdomain is disabled.  OMAP4 requires a different
approach: the hwmod code needs to signal the clockdomain code when to
force-enable and auto-idle a clockdomain during the IP block enable
process.  The current conjecture is that once that hwmod sequence is
implemented, it will no longer be necessary for the clock code to call
into the clockdomain code for "optional clocks" on OMAP4.

Add a static flag to the OMAP2+ clock code, clkdm_control, that by
default preserves the OMAP2/3 behavior.  Also add a function,
omap2_clk_disable_clkdm_control(), intended to be called from OMAP4
and beyond clock initcalls, that disables the old behavior.

Part of this patch was originally based on a patch by Rajendra Nayak
<rnayak@ti.com>.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>