Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a ("driver: base: Disable
   CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
   made default to 'n',
2. It is not recommended (help message: "This should not be used today
   [...] creates a high system load") and was kept only for ancient
   userland,
3. Certain userland specifically requests it to be disabled (systemd
   README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When testing out gpio-keys with a button, a spurious
interrupt (and therefore a key press or release event)
gets triggered as soon as the driver enables the irq
line for the first time.

This patch clears any potential bogus generated interrupt
that was caused by the switching of the associated irq's
type and polarity.
Signed-off-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

"git diff" says:

    \ No newline at end of file

after modifying the file.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
[mpe: Rebase since addition of another test]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit ddf35cf3 ("powerpc: Use barrier_nospec in copy_from_user()")
Added barrier_nospec before loading from user-controlled pointers. The
intention was to order the load from the potentially user-controlled
pointer vs a previous branch based on an access_ok() check or similar.

In order to achieve the same result, add a barrier_nospec to the
raw_copy_in_user() function before loading from such a user-controlled
pointer.

Fixes: ddf35cf3 ("powerpc: Use barrier_nospec in copy_from_user()")
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When emulating tsr, treclaim and trechkpt, we incorrectly set CR0. The
code currently sets:
    CR0 <- 00 || MSR[TS]
but according to the ISA it should be:
    CR0 <-  0 || MSR[TS] || 0

This fixes the bit shift to put the bits in the correct location.

This is a data integrity issue as CR0 is corrupted.

Fixes: 4bb3c7a0 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Cc: stable@vger.kernel.org # v4.17+
Tested-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The powernv platform uses @dma_iommu_ops for non-bypass DMA. These ops
need an iommu_table pointer which is stored in
dev->archdata.iommu_table_base. It is initialized during
pcibios_setup_device() which handles boot time devices. However when a
device is taken from the system in order to pass it through, the
default IOMMU table is destroyed but the pointer in a device is not
updated; also when a device is returned back to the system, a new
table pointer is not stored in dev->archdata.iommu_table_base either.
So when a just returned device tries using IOMMU, it crashes on
accessing stale iommu_table or its members.

This calls set_iommu_table_base() when the default window is created.
Note it used to be there before but was wrongly removed (see "fixes").
It did not appear before as these days most devices simply use bypass.

This adds set_iommu_table_base(NULL) when a device is taken from the
system to make it clear that IOMMU DMA cannot be used past that point.

Fixes: c4e9d3c1 ("powerpc/powernv/pseries: Rework device adding to IOMMU groups")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing
which reads "assigned-addresses" of every PCI device and initializes
the device resources. However if the property is missing or zero sized,
then there is no fallback of any kind and the PCI resources remain
undiscovered, i.e. pdev->resource[] array remains empty.

This adds a fallback which parses the "reg" property in pretty much same
way except it marks resources as "unset" which later make Linux assign
those resources proper addresses.

This has an effect when:
1. a hypervisor failed to assign any resource for a device;
2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try
assigning a resource.
Neither is likely to happen under PowerVM.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

So far the pseries platforms has always been using IOMMU making
SWIOTLB unnecessary. Now we want secure guests which means devices can
only access certain areas of guest physical memory; we are going to
use SWIOTLB for this purpose.

This allows SWIOTLB for pseries. By default there is no change in
behavior.

This enables SWIOTLB when the "swiotlb" kernel parameter is set to
"force".

With the SWIOTLB enabled, the kernel creates a directly mapped DMA
window (using the usual DDW mechanism) and implements SWIOTLB on top
of that.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The commit 8617a5c5 ("powerpc/dma: handle iommu bypass in
dma_iommu_ops") merged direct DMA ops into the IOMMU DMA ops allowing
SWIOTLB as well but only for mapping; the unmapping and bouncing parts
were left unmodified.

This adds missing direct unmapping calls to .unmap_page() and
.unmap_sg().

This adds missing sync callbacks and directs them to the direct DMA
hooks.

Fixes: 8617a5c5 ("powerpc/dma: handle iommu bypass in dma_iommu_ops")
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NThiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use the dma_get_mask() helper from dma-mapping.h instead, as they are
functionally identical.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If you compile with KVM but without CONFIG_HAVE_HW_BREAKPOINT you fail
at linking with:
  arch/powerpc/kvm/book3s_hv_rmhandlers.o:(.text+0x708): undefined reference to `dawr_force_enable'

This was caused by commit c1fe190c ("powerpc: Add force enable of
DAWR on P9 option").

This moves a bunch of code around to fix this. It moves a lot of the
DAWR code in a new file and creates a new CONFIG_PPC_DAWR to enable
compiling it.

Fixes: c1fe190c ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: NMichael Neuling <mikey@neuling.org>
[mpe: Minor formatting in set_dawr()]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In commit c1fe190c ("powerpc: Add force enable of DAWR on P9
option") the following piece of code was added:

   smp_call_function((smp_call_func_t)set_dawr, &null_brk, 0);

Since GCC 8 this triggers the following warning about incompatible
function types:

  arch/powerpc/kernel/hw_breakpoint.c:408:21: error: cast between incompatible function types from 'int (*)(struct arch_hw_breakpoint *)' to 'void (*)(void *)' [-Werror=cast-function-type]

Since the warning is there for a reason, and should not be hidden behind
a cast, provide an intermediate callback function to avoid the warning.

Fixes: c1fe190c ("powerpc: Add force enable of DAWR on P9 option")
Suggested-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NMathieu Malaterre <malat@debian.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

ISA v3.0 radix modes provide SLBIA variants which can invalidate ERAT
for effPID!=0 or for effLPID!=0, which allows user and guest
invalidations to retain kernel/host ERAT entries.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This makes it clear to the caller that it can only be used on POWER9
and later CPUs.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
[mpe: Use "ISA_3_0" rather than "ARCH_300"]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Branch to the relocated 0xc000 address early (still in real mode), to
simplify subsequent branches. Have the virt mode handler avoid just
'windup' and redo the exception from scratch, rather than branching
back to the trampoline.

Rearrange the stack setup instruction location to match the system
reset handler (e.g., right before EXCEPTION_PROLOG_COMMON).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Follow convention and move tramp ahead of common.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The idle wake up code in the system reset interrupt is not very
optimal. There are two requirements: perform idle wake up quickly;
and save everything including CFAR for non-idle interrupts, with
no performance requirement.

The problem with placing the idle test in the middle of the handler
and using the normal handler code to save CFAR, is that it's quite
costly (e.g., mfcfar is serialising, speculative workarounds get
applied, SRR1 has to be reloaded, etc). It also prevents the standard
interrupt handler boilerplate being used.

This pain can be avoided by using a dedicated idle interrupt handler
at the start of the interrupt handler, which restores all registers
back to the way they were in case it was not an idle wake up. CFAR
is preserved without saving it before the non-idle case by making that
the fall-through, and idle is a taken branch.

Performance seems to be in the noise, but possibly around 0.5% faster,
the executed instructions certainly look better. The bigger benefit is
being able to drop in standard interrupt handlers after the idle code,
which helps with subsequent cleanup and consolidation.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
[mpe: Fixup BE by using DOTSYM for idle_return_gpr_loss call]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The bad stack test in interrupt handlers has a few problems. For
performance it is taken in the common case, which is a fetch bubble
and a waste of i-cache.

For code development and maintainence, it requires yet another stack
frame setup routine, and that constrains all exception handlers to
follow the same register save pattern which inhibits future
optimisation.

Remove the test/branch and replace it with a trap. Teach the program
check handler to use the emergency stack for this case.

This does not result in quite so nice a message, however the SRR0 and
SRR1 of the crashed interrupt can be seen in r11 and r12, as is the
original r1 (adjusted by INT_FRAME_SIZE). These are the most important
parts to debugging the issue.

The original r9-12 and cr0 is lost, which is the main downside.

  kernel BUG at linux/arch/powerpc/kernel/exceptions-64s.S:847!
  Oops: Exception in kernel mode, sig: 5 [#1]
  BE SMP NR_CPUS=2048 NUMA PowerNV
  Modules linked in:
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted
  NIP:  c000000000009108 LR: c000000000cadbcc CTR: c0000000000090f0
  REGS: c0000000fffcbd70 TRAP: 0700   Not tainted
  MSR:  9000000000021032 <SF,HV,ME,IR,DR,RI>  CR: 28222448  XER: 20040000
  CFAR: c000000000009100 IRQMASK: 0
  GPR00: 000000000000003d fffffffffffffd00 c0000000018cfb00 c0000000f02b3166
  GPR04: fffffffffffffffd 0000000000000007 fffffffffffffffb 0000000000000030
  GPR08: 0000000000000037 0000000028222448 0000000000000000 c000000000ca8de0
  GPR12: 9000000002009032 c000000001ae0000 c000000000010a00 0000000000000000
  GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
  GPR20: c0000000f00322c0 c000000000f85200 0000000000000004 ffffffffffffffff
  GPR24: fffffffffffffffe 0000000000000000 0000000000000000 000000000000000a
  GPR28: 0000000000000000 0000000000000000 c0000000f02b391c c0000000f02b3167
  NIP [c000000000009108] decrementer_common+0x18/0x160
  LR [c000000000cadbcc] .vsnprintf+0x3ec/0x4f0
  Call Trace:
  Instruction dump:
  996d098a 994d098b 38610070 480246ed 48005518 60000000 38200000 718a4000
  7c2a0b78 3821fd00 41c20008 e82d0970 <0981fd00> f92101a0 f9610170 f9810178
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Since the system reset interrupt began to use its own stack, and
machine check interrupts have done so for some time, r1 can be
changed without clearing MSR[RI], provided no other interrupts
(including SLB misses) are taken.

MSR[RI] does have to be cleared when using SCRATCH0, however.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Although the 0x1500 interrupt only applies to bare metal, it is better
to just use the standard macro for scratch save.

Runtime code path remains unchanged (due to instruction patching).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Some exception entry requires DAR and/or DSISR to be saved into the
paca exception save area. Add options to the standard exception
macros for these.

Generated code changes slightly due to code structure.

-     554:      a6 02 72 7d     mfdsisr r11
-     558:      a8 00 4d f9     std     r10,168(r13)
-     55c:      b0 00 6d 91     stw     r11,176(r13)
+     554:      a8 00 4d f9     std     r10,168(r13)
+     558:      a6 02 52 7d     mfdsisr r10
+     55c:      b0 00 4d 91     stw     r10,176(r13)
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Restore all SPRs and CR up-front, these are longer latency
instructions. Move register restore around to maximise pairs of
adjacent loads (e.g., restore r0 next to r1).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Duplicate the hmi windup code for both cases, rather than to put a
special case branch in the middle of it. Remove unused label. This
helps with later code consolidation.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move in_mce decrement earlier before registers are restored (but
still after RI=0). This helps with later consolidation.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Trivial code change, r3->r9.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

All supported 64s CPUs support mtmsrd L=1 instruction, so a cleanup
can be made in sreset and mce handlers.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move SPR reads ahead of writes. Real mode entry that is not a KVM
guest is rare these days, but bad practice propagates.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

syscall / hcall entry unnecessarily differs between KVM and non-KVM
builds. Move the SMT priority instruction to the same location
(after INTERRUPT_TO_KERNEL).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change. Final vmlinux is changed only due to change
in bug table line numbers.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Generally, macros that result in instructions being expanded are
indented by a tab, and those that don't have no indent. Fix the
obvious cases that go contrary to style.

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No generated code change.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>