This patch (as1079) cleans up the way URB_* flags are exported in
usbfs.

	The URB_NO_INTERRUPT flag is now exported (this is the
	only behavioral change).

	USBDEVFS_URB_* macros are added for URB_NO_FSBR,
	URB_ZERO_PACKET, and URB_NO_INTERRUPT, making explicit the
	fact that the kernel accepts them.

	The flag matching takes into account that the URB_* values
	may change as the kernel evolves, whereas the USBDEVFS_URB_*
	values must remain fixed since they are a user API.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1072) fixes some recently-introduced compile problems
that show up in ehci-hcd when CONFIG_PM is turned off.

	PORT_WAKE_BITS needs to be defined always.

	ehci_port_power() is called during initialization by all the
	EHCI variants other than the PCI version, in which it is
	"defined but not used".  So add a call to it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Simplify processing of completed qtds, and correct handling of short
reads, by removing two state variables:

 - "qtd_status" wasn't needed.  The current URB's status is either
   OK (-EINPROGRESS) or some fault status.  Once a fault appears,
   the queue halts and any later QTDs are immediately removed, so
   no temporary status is needed.  (Or for typical short reads,
   it's not treated as a fault, so no queue halt is needed.)

 - "do_status" was erroneous.  Because of how the queue is set up,
   short control reads can (and should!) be treated like full size
   reads, and cleaned up the usual way.  The status stage will be
   executed transparently, and usbcore handles the choice of whether
   to report this status as unexected.
 
The "do_status" problem caused a rather perplexing timing-dependent
problem with usbtest case 10.  Sometimes it would make the controller
skip a dozen transactions while (wrongly) trying to clean up after a
short transfer.  Fortunately, removing a dcache contention issue made
this become trivial to reproduce (on one test rig), so enough clues
finally presented themselves ... I think this has been around for a
very long time, but was worsened by recent urb->status changes.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix bogus assignment of "unsigned char *" to "char *":  preserve
unsignedness.  These values are used directly as descriptor lengths
when iterating through the buffer, so this *could* cause oddness
that potentially includes oopsing.  (IMO not likely, except as
part of a malicious device...)

Fix the bogus warning in CDC ACM which highlighted this problem
(by showing a negative descriptor type).  It uses the undesirable
legacy err() for something that's not even an error; switch to
use dev_dbg, and show descriptor types in hex notation to match
the convention for such codes.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add Documentation about callbacks in USB.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled.  Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub.  This approach turns out to be subject to races, resulting
in unnecessary polling.

The patch does away with the method entirely.  Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present.  This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1068b) disables the RD interrupt flag when an OHCI root
hub is suspended with remote wakeup disabled.  Although the spec
clearly states that this flag permits the controller to issue an
interrupt when a resume request from downstream is detected and not
when a local status change occurs, some controllers mistakenly use it
for both types of event.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting.  The setting
is then saved in the do_remote_wakeup flag.

Later on, however, the device_may_wakeup() value can change because of
user activity.  So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup().  This patch (as1076)
makes that change for root hubs in several places.

The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.

And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1061) makes g_file_storage more compliant with the
Bulk-Only Transport specification.  After an invalid CBW is received,
the gadget must ignore any further bulk-OUT data until it is reset.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove the unused check for num_interrupt and friends as well as remove
them from the header file because no usb-serial drivers no longer
reference them.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb-serial core no longer checks these fields so remove them from
all of the individual drivers.  They will be removed from the usb-serial
core in a patch later in the series.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Setting DTR et al. should work for all interfaces
if you actually pass the interface number. :-P
 
This should help with devices that have important pseudo-serial ports
that aren't on the first interface in the device.
Signed-off-by: NChris Collins <chris@ursys.com.au>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds documentation about the new usb anchor infrastructure.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Provide better comments about qh_completions() and QTD handling.
That code can be *VERY* confusing, since it's evolved over a few
years to cope with both hardware races and silicon quirks.

Remove two unlikely() annotations that match the GCC defaults
(and are thus pointless); add an "else" to highlight code flow.

This patch doesn't change driver behavior.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1077) logs an error message whenever the kernel is
unable to enumerate a new USB device.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Comments here are so outdated that they are plain wrong. We cannot expect
people to write correct drivers if the headers have incorrect comments.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Given that most of drivers/usb/serial/Kconfig is wrapped inside:

  if USB_SERIAL
  ...
  endif # USB_SERIAL

remove the consequently redundant dependencies on USB_SERIAL.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the ability to trigger asynchronous unlinks of anchored URBs. This
is needed for error handling in the comntext of completion handlers, which
cannot sleep.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can
support SH7366 USB host by changing several R8A66597 code.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the problem that enumeration of a USB device was slow.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver ignored the value of bInterval and revised the problem
that performed interrupt transfer.

ASIX USB Ethernet adapter comes to work with this host controller
by applying this patch.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removes unimplemented TCFLSH handling from oti6858, because it was 
preventing TCFLSH handling by upper layer (line discipline) drivers (see 
drivers/char/tty_io.c line 3450).
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch refactors some shutdown code so it can be shared between
ehci_stop() and ehci_shutdown().

This also fixes a couple potential bugs:
 - ehci_shutdown() was not locking ehci->lock before halting the HC.
 - ehci_shutdown() didn't disable the watchdog and IAA timers.
 - ehci_stop() was resetting the host controller when it may have been
   running, which the EHCI spec says "may result in undefined behavior".

ehci_stop() was calling port_power() to turn off the ports, which waited
20ms after applying the port change.  The msleep was for the case where
the HC might take 20ms to turn the ports on; since we're shutting them
off, we can avoid the msleep and just use ehci_turn_off_ports().

ehci_stop() doesn't need to clear the intr_enable register or revert
ownership of the companion controllers to the BIOS, because the host
controller reset should have done that.  There might be a buggy host
controller that doesn't follow the reset rules, but for now we assume
it's redundant code and remove it.

[ A subsequent patch will cancel the timers later ... this version
carries forward existing bugs where timers could get re-armed
after they're canceled. ]
Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The at91sam9 chip are ARMv5 so they support preload instructions.
Use preloading to load the FIFO a bit faster.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1075) changes dummy-hcd to dynamically allocate its
platform_device structures, using the core platform_device_alloc()
interface.  This is what it should have done all along, because the
dynamically-allocated structures have a release method in the driver
core and are therefore immune to being released after the module has
been unloaded.

Thanks to Richard Purdie for pointing out the need for this change.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Restore some section annotations:  they were switched to "__devinit"
while they should have been "__init", because of bogus warnings.  The
warnings are now fixed, so the runtime footprint of various drivers
can now shrink a bit.  On ARMv5, it's about 600 bytes except for the
Ethernet gadget, where it can save a bit more.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removing an interface's sysfs files before unregistering the interface
doesn't work properly, because usb_unbind_interface() will reinstall
altsetting 0 and thereby create new sysfs files.  This patch (as1074)
removes the files after the unregistration is finished.  It's not
quite as clean, but at least it works.

Also, there's no need to check if an interface has been registered
before removing its sysfs files.  If it hasn't been registered then
the files won't have been created, so usb_remove_sysfs_intf_files()
will simply do nothing.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The kernel is written in C, not C++, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed.  These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.

Until now these jobs have been carried out when the root hub is
resumed, not when the controller is.  Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed.  But this is wasteful and
unnecessary.

To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers.  They can call the new routine instead of
resuming their root hubs.  And ohci-pci.c can call it instead of using
its own special-purpose handler.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers.  They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.

To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume.  It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator.  However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications.  This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB is moving to transfering status as a parameter. To ease the transition
urb->status is to be touched only once in a function. The xpad driver has
been overlooked. Dmitry wants this to go through the USB tree.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1063) fixes a bug in the way ohci-hcd resumes its
controllers.  It leaves the Master Interrupt Enable bit turned off.

If the root hub is resumed immediately this won't matter.  But if the
root hub is suspended (say because no devices are plugged in), it won't
ever wake up by itself.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a messed up combination of two nested switch statements in
drivers/usb/gadget/dummy_hcd.c.

According to the USB spec (section 5.8.3) the maximum packet size for bulk
endpoints can be 512 for high-speed devices and 8, 16, 32 or 64 for full-speed
devices.  Low-speed devices must not have bulk endpoints.
Signed-off-by: NIngo van Lil <inguin@gmx.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In drivers/usb/gadget/amd5536udc.c::udc_pci_probe(), sizeof(struct udc)
storage is allocated for 'dev'.

There are many exit points from the function where 'dev' is not free'd but has
also not yet been used for anything.  The following patch free's 'dev' at the
return points where it has not yet been used.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1060) makes usb-storage set the DMA alignment mask for
SCSI slaves to match the maxpacket size of the bulk-IN endpoint,
rather than always setting it to 511.  For full-speed devices that
mask is too restrictive, and wireless USB devices can have maxpacket
sizes larger than 512.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

G_PRINTER: Bug fix for blocking reads and a fix for a memory leak.

This fixes bugs in blocking IO calls. When the poll() entry point
is called receive transfers will be setup if they have not already
been. Another bug fix is that the poll() entry point now checks the
current receive buffer for data when reporting if any data had been
received. A memory leak was fixed that could have occurred when a
USB reset happened.
Signed-off-by: NCraig W. Nadler <craig@nadler.us>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

platform_get_resource() may return null, so although it seems it will never
do so here unless there's a bug elsewhere, it does no harm to be defensive
and test.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove obsolete contact addresses.
Signed-off-by: NMatti Linnanvuori <mattilinnanvuori@yahoo.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove useless @type note for rh_string() and @r note for usb_hcd_irq()
since this two parameters were removed.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>