Signed-off-by: NUk Kim <w0806.kim@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

When we disable the WM8994 FLL code path sharing means that we end up
writing out a configuration. Currently this is the currently active
input and output frequency (which causes snd_soc_update_bits() to
suppress actual writes both immediately and in the common case where
we reenable the same configuration later) but we allow machine drivers
to pass through a source of zero. Since the register values written
are one less than the source constants this causes corruption of other
bitfields in the register.

Fix this by using the most recently configured FLL source when none is
provided.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

Update some of the default configuration for the device to improve
the performance.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

We need a post notification as we need to shut down the MBC after the
data stops flowing rather than before.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This allows us to communicate our power management state back to the
parent device, allowing it to do a full power down when the device is
idle.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8994 and WM8958 register map is relatively sparse so benefits
from compression. The rbtree compression gives better results than
LZO for both memory and CPU consumption on a map as sparse as this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In the process we convert the driver to read registers one at a time
when initialising the cache. This has the effect of working around
limitations in the sizes of I2C transactions which can be done by some
CPUs. Due to the sparseness of the register map the overhead from this
should be minimual unless I2C transactions are very expensive to start.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 contains an advanced accessory detection feature which allows
detection of up to seven different impedence levels on the microphone
bias output, including detection of video outputs. Since some of the
more involved accessory interfaces may involve noticable interactions
with external components a simple detection scheme is provided by
default with the option to provide custom handling of accessory detect.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 features a multi-band compressor which can be enabled on
any of the AIF inputs. The MBC allows different gains to be applied to
differnt audio bands, providing an improvement in perceived loudness
of the signal by avoiding overdriving the output transducers. This
patch enables support for the MBC.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Additional audio routing options are available on the WM8958 audio
interface 3. Add support for these.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 is a WM8994 derivative. This patch merely ensures that some
revision specific configuration for WM8994 is not enabled on WM8994,
additional patches will add support for the new features introduced on
the WM8958.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

They went AWOL during the multi-component merge.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

There is no need to include soc-dapm.h since soc.h includes it.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Makes the WM8994 driver file itself substantially smaller.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Allow the application to choose if the ADC data presented on the left
and right channels is sourced from the internal left or right channel.
This allows a mono recording to be presented as stereo on the external
bus.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

During the multi-component conversion the WM8994 register cache init
got lost.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.

This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.

This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.

Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We now have trace in the ASoC core so we don't need to our own trace in
the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Providing the analogue configuration of the output path remains the same
the DC offset corrected by the DC servo will remain identical so we can
skip the callibration, reducing the startup time for the headphone output.
Implement this for the wm_hubs devices as has been done for several other
CODECs.

Don't do this if we have any analogue paths enabled since offsets may be
being introduced by the analogue paths which could vary outside the
control of the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Remove unused vol from struct access_mask

Reduces object size ~3kb.

$ size sound/soc/codecs/wm8994.o*
   text	   data	    bss	    dec	    hex	filename
  40727	   4384	   4480	  49591	   c1b7	sound/soc/codecs/wm8994.o.new
  43879	   4384	   4480	  52743	   ce07	sound/soc/codecs/wm8994.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

WM8994 relies on the DAIs having IDs that match the AIF numbers.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NIan Lartey <ian@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow selection of the channel used for input to the AIFnDAC signals.
This isn't integrated into DAPM since we treat the data as a single
mono channel until just beyond this selection so it ends up having
no visible effect on the routing.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This makes it that little bit easier to spot the diagnostics in the
logs.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Any subsequent revisions will have these configuration changes applied
by default.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Change the chip defaults to optimise performance of some of the DSP
functionality.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.

 struct snd_soc_codec    --->  struct snd_soc_codec (device data)
                          +->  struct snd_soc_codec_driver (driver data)

 struct snd_soc_platform --->  struct snd_soc_platform (device data)
                          +->  struct snd_soc_platform_driver (driver data)

 struct snd_soc_dai      --->  struct snd_soc_dai (device data)
                          +->  struct snd_soc_dai_driver (driver data)

 struct snd_soc_device   --->  deleted

This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.

The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.

This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.

Other notable multi-component changes:-

 * Stream operations now de-reference less structures.
 * close_delayed work() now runs on a DAI basis rather than looping all DAIs
   in a card.
 * PM suspend()/resume() operations can now handle N CODECs and Platforms
   per sound card.
 * Added soc_bind_dai_link() to bind the component devices to the sound card.
 * Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
   DAI link components.
 * sysfs entries can now be registered per component per card.
 * snd_soc_new_pcms() functionailty rolled into dai_link_probe().
 * snd_soc_register_codec() now does all the codec list and mutex init.

This patch changes the probe() and remove() of the CODEC drivers as follows:-

 o Make CODEC driver a platform driver
 o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
 o Removed all static codec pointers (drivers now support > 1 codec dev)
 o snd_soc_register_pcms() now done by core.
 o snd_soc_register_dai() folded into snd_soc_register_codec().

CS4270 portions:
Acked-by: NTimur Tabi <timur@freescale.com>

Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>

TI CODEC and OMAP fixes
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>

Samsung platform and misc fixes :-
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NSeungwhan Youn <sw.youn@samsung.com>

MPC8610 and PPC fixes.
Signed-off-by: NTimur Tabi <timur@freescale.com>

i.MX fixes and some core fixes.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

J4740 platform fixes:-
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>

CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

AIF1ADC TDM mode has no effect other than causing the ADCDAT line to
be tristated rather than driven low on clock cycles where there is no
data to be transmitted. If the clock cycle is idle then there should
be no devices using the data so tristating should have no adverse
effects.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8994 can output a clock derived from its internal SYSCLK, called
OPCLK.  The rate can be selected as a sysclk, with a division from the
SYSCLK rate specified (multiplied by 10 since a division of 5.5 is
supported) and the clock can be disabled by specifying a divisor of
zero.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Very handy for debug.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

If the FLL is not configured attempting to resume it will produce a
warning message so skip the resume.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It's a little verbose during path changes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>