- 25 9月, 2006 37 次提交
-
-
由 Tony Lindgren 提交于
Fix spinlock recursion for dyntick. Modified version based on Imre Deak's earlier patch. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Komal Shah 提交于
ARM11 can't access the IVA interrupt controller from IVA slave port. From Richard Woodruff: "The 0x40000000 is an IVA-ARM7 local bus address. The IVA-INTC is NOT accessible through the IVA-L3-Slave Port. The current TRM does say this directly and indirectly in a few spots and in figures." Signed-off-by: NKomal Shah <komal_shah802003@yahoo.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Tony Lindgren 提交于
This is needed to reset GPIO after free_irq(). Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Juha Yrjola 提交于
After adjusting clock parameters, OMAP2 CPUs need a memory barrier to make sure the changes go into effect immediately. Otherwise bad things will happen if we try to access the peripheral whose clock is just being enabled. Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Samuel Ortiz 提交于
A forgotten parenthesis in clock.c caused the PLL stabilization loop to not be executed correctly. Signed-off-by: NSamuel Ortiz <samuel.ortiz@solidboot.com> Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Timo Teras 提交于
This patch makes the OMAP2 dmtimers module using the interface clocks only while the registers are accessed (except GPT1 which has iclk enabled all the time). Signed-off-by: NTimo Teras <timo.teras@solidboot.com> Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Tony Lindgren 提交于
Also export some omap24xx specific DMA functions. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Imre Deak 提交于
Add support for assigning memory regions dynamically to peripherals attached to GPMC interface. Platform specific code should now call gpmc_cs_request to get a free GPMC memory region instead of using a fixed address. Make the H4 and Apollon platform initialization use the new API. Signed-off-by: NImre Deak <imre.deak@solidboot.com> Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Jonathan McDowell 提交于
This patch adds some further #defines regarding GPIOs and latch bits for the Amstrad Delta; the drivers that use them will be submitted at a later date but there's no reason not to have the information already there and available for use. Signed-off-by: NJonathan McDowell <noodles@earth.li> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Jonathan McDowell 提交于
The recent MPUIO range change fix breaks compilation if CONFIG_ARCH_OMAP24XX isn't defined; it should be OMAP_MAX_GPIO_LINES not MAX_GPIO_LINES I believe. This one liner fixes it. Signed-off-by: NJonathan McDowell <noodles@earth.li> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Mark Howell 提交于
This patch adds pin mux info for the SPI master/slave interface on OMAP16xx. Data from OMAP 1611/1612 TRM and errata. Works for me on my 1611/H2 with current git kernel. Signed-off-by: NMark Howell <mhowell@northlink.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Imre Deak 提交于
We have to make sure that the LCD DMA external destination bit is cleared by default, otherwise OMAP won't sleep. Signed-off-by: NImre Deak <imre.deak@solidboot.com> Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Imre Deak 提交于
- MPUIO doesn't exist on OMAP2 - no error was returned for too big MPUIO numbers Signed-off-by: NImre Deak <imre.deak@solidboot.com> Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Tony Lindgren 提交于
McBSP does not need sys_ck or sys_clkout. If the devices connected to McBSP need sys_clkout, they need to request it. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Kyungmin Park 提交于
Apollon board MMC supports on OMAP2 TODO: We have to check MMC on H4 Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Kevin Hilman 提交于
ARM: OMAP: Fix SRAM static mapping for EMU devices. Fix SRAM static mapping for EMU devices. Signed-off-by: NKevin Hilman <khilman@deeprooted.net> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Samuel Ortiz 提交于
Signed-off-by: NSamuel Ortiz <samuel.ortiz@solidboot.com> Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Imre Deak 提交于
Reprogramming takes places before putting the CPU into idle mode if the dynamic tick option is enabled. The timer is then set to expire at the next pending timer event. Because some time has already passed since the last reported jiffy we have to wait less than the time specified in jiffies. Also make sure we don't set a load value of 0 whose outcome is unspecified according to the TRM. Signed-off-by: NImre Deak <imre.deak@solidboot.com> Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Tony Lindgren 提交于
If we call clk_get() from arch_reset we get ugly messages before reboot. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
To whoever had written that code: a) priority of >> is higher than that of & b) priority of typecast is higher than that of any binary operator c) learn the fscking C Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
ql3xxx_probe() does ioremap and stores result in ->mem_map_registers. On failure exit it does iounmap() of the same thing. OTOH, ql3xxx_remove() does iounmap() of ->mmap_virt_base which is (a) never assigned and (b) never used other than in that iounmap() call. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
the driver is still shite, though... Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Matthew Wilcox 提交于
Some user tools parse /proc/scsi/scsi, so we can't yet change the names. Change the existing ones back to their old names, and add an admonition to not make the same mistake that I did. Andrew Morton reports that this was breaking YDL 4.1 userspace. Signed-off-by: NMatthew Wilcox <matthew@wil.cx> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
git://git.infradead.org/~dwmw2/khdrs-2.6由 Linus Torvalds 提交于
* git://git.infradead.org/~dwmw2/khdrs-2.6: Don't remove $(INSTALL_HDR_PATH)/install before headers_install.
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
marked as such... Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
no ioread*(), for one thing Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 David Woodhouse 提交于
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2由 Linus Torvalds 提交于
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (28 commits) ocfs2: Teach ocfs2_drop_lock() to use ->set_lvb() callback ocfs2: Remove ->unblock lockres operation ocfs2: move downconvert worker to lockres ops ocfs2: Remove unused dlmglue functions ocfs2: Have the metadata lock use generic dlmglue functions ocfs2: Add ->set_lvb callback in dlmglue ocfs2: Add ->check_downconvert callback in dlmglue ocfs2: Check for refreshing locks in generic unblock function ocfs2: don't unconditionally pass LVB flags ocfs2: combine inode and generic blocking AST functions ocfs2: Add ->get_osb() dlmglue locking operation ocfs2: remove ->unlock_ast() callback from ocfs2_lock_res_ops ocfs2: combine inode and generic AST functions ocfs2: Clean up lock resource refresh flags ocfs2: Remove i_generation from inode lock names ocfs2: Encode i_generation in the meta data lvb ocfs2: Free up some space in the lvb ocfs2: Remove special casing for inode creation in ocfs2_dentry_attach_lock() ocfs2: manually d_move() during ocfs2_rename() [PATCH] Allow file systems to manually d_move() inside of ->rename() ...
-
git://git.infradead.org/~dwmw2/khdrs-2.6由 Linus Torvalds 提交于
* git://git.infradead.org/~dwmw2/khdrs-2.6: New 'make headers_install_all' target. Use dependencies for 'make headers_install'. [S390] Unexport <asm/z90crypt.h>, export <asm/zcrypt.h> in its place. Remove dead netfilter_logging.h from include/linux/Kbuild Remove offsetof() from user-visible <linux/stddef.h> Clean up exported headers on CRIS Fix v850 exported headers Don't advertise (or allow) headers_{install,check} where inappropriate. Remove UML header export Remove ARM26 header export. Fix H8300 exported headers. Fix m68knommu exported headers Fix exported headers for SPARC, SPARC64 Fix 'make headers_check' on m32r Fix 'make headers_check' on sh64 Fix 'make headers_check' on sh [HEADERS] Fix ARM 'make headers_check' Initial pass of manual conflict resolution in top-level Makefile over conflicting build rule and headers_install changes.
-
git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (28 commits) kbuild: add distclean info to 'make help' and more details for 'clean' dontdiff: add utsrelease.h kbuild: fix "mkdir -p" usage in scripts/package/mkspec kbuild: correct and clarify versioning info in Makefile kbuild: fixup Documentation/kbuild/modules.txt kbuild: Extend kbuild/defconfig tags support to exuberant ctags kbuild: fix for some typos in Documentation/makefiles.txt kbuild: clarify "make C=" build option Documentaion: update Documentation/Changes with minimum versions kbuild: update help in top level Makefile kbuild: fail kernel compilation in case of unresolved module symbols kbuild: remove debug left-over from Makefile.host kbuild: create output directory for hostprogs with O=.. build kbuild: add missing return statement in modpost.c:secref_whitelist() kbuild: preperly align SYSMAP output kbuild: make -rR is now default kbuild: make V=2 tell why a target is rebuild kbuild: modpost on vmlinux regardless of CONFIG_MODULES kbuild: ignore references from ".pci_fixup" to ".init.text" kbuild: linguistic fixes for Documentation/kbuild/makefiles.txt ...
-
- 26 9月, 2006 1 次提交
-
-
由 Jesper Juhl 提交于
Add distclean info, that was previously missing, to 'make help'. Also add a few more details to the 'make clean' help text. Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com> Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
-
- 25 9月, 2006 2 次提交
-
-
由 Randy Dunlap 提交于
Add auto-generated utsrelease.h to dontdiff file. Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
-
由 Rolf Eike Beer 提交于
"mkdir -p" does not only mean not to complain if the directory already exists, but also to create the parent directories if needed. This patch removes "lib" from the list of directories to create as we will also create "lib/modules". Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
-