Repeated variable use and line wrapping is hard to read.
Use temp variables instead of direct references.

struct fifo_info *fifo = &mac_control->fifos[i];
struct ring_info *ring = &mac_control->rings[i];
struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pfifo_fast_enqueue has this check:
        if (skb_queue_len(list) < qdisc_dev(qdisc)->tx_queue_len) {

which allows each band to enqueue upto tx_queue_len skbs for a
total of 3*tx_queue_len skbs. I am not sure if this was the
intention of limiting in qdisc.

Patch compiled and 32 simultaneous netperf testing ran fine. Also:
# tc -s qdisc show dev eth2
qdisc pfifo_fast 0: root bands 3 priomap  1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
 Sent 16835026752 bytes 373116 pkt (dropped 0, overlimits 0 requeues 25) 
 rate 0bit 0pps backlog 0b 0p requeues 25 
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch compiled and 32 simultaneous netperf testing ran fine.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch compiled and 32 simultaneous netperf testing ran fine.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dropped skb's should be documented by an appropriate return value.
Use the correct NET_RX_DROP and NET_RX_SUCCESS values for that reason.
Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the tests that check whether Frame* bits are not set
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements suspend/resume and WOL support for UCC Ethernet
driver.

We support two wake up events: wake on PHY/link changes and wake
on magic packet.

In some CPUs (like MPC8569) QE shuts down during sleep, so magic packet
detection is unusable, and also on resume we should fully reinitialize
UCC structures.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes currently unused UGETH_MAGIC_PACKET Kconfig symbol
and code, i.e. magic_packet_detection_{enable,disable} functions.

The two functions each contain just two steps that we'll place into
suspend/resume code path under CONFIG_PM.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch factors out MAC initialization into ucc_geth_init_mac()
function that we'll use for suspend/resume.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some CPUs (i.e. MPC8569) QE shuts down completely during sleep,
drivers may want to know that to reinitialize registers and buffer
descriptors.

This patch implements qe_alive_during_sleep() helper function, so far
it just checks if MPC8569-compatible power management controller is
present, which is a sign that QE turns off during sleep.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 3e73fc9a ("ucc_geth: Fix IO
memory (un)mapping code") I fixed ug_regs IO memory leak by properly
freeing the allocated memory. But ethtool_stats() callback doesn't
check for ug_regs being NULL, and that causes following oops if
'ethtool -S' is executed on a closed eth device:

  Unable to handle kernel paging request for data at address 0x00000180
  Faulting instruction address: 0xc0208228
  Oops: Kernel access of bad area, sig: 11 [#1]
  ...
  NIP [c0208228] uec_get_ethtool_stats+0x38/0x140
  LR [c02559a0] ethtool_get_stats+0xf8/0x23c
  Call Trace:
  [ef87bcd0] [c025597c] ethtool_get_stats+0xd4/0x23c (unreliable)
  [ef87bd00] [c025706c] dev_ethtool+0xfe8/0x11bc
  [ef87be00] [c0252b5c] dev_ioctl+0x454/0x6a8
  ...
  ---[ end trace 77fff1162a9586b0 ]---
  Segmentation fault

This patch fixes the issue.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.101.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the tx_prod, tx_cons, tx_pending, tx_ring, and
tx_buffers transmit ring device members to a per-interrupt structure.
It also adds a new transmit producer mailbox member (prodmbox) and
converts the code to use it rather than a preprocessor constant.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the rx_rcb, rx_rcb_mapping, and rx_rcb_ptr return ring
device members to a per-interrupt structure.  It also adds a new return
ring consumer mailbox register member (consmbox) and converts the code
to use it rather than a preprocessor constant.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the last_tag, last_tag_irq, and hw_status device
members to a per-interrupt structure.  It also adds a new interrupt
mailbox member (int_mbox) and converts the code to use it rather than a
direct preprocessor constant.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the napi interrupt handler functions to accept and
use tg3_napi structures.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch migrates the ISR parameter from struct net_device to struct
tg3_napi.  Checkpatch complains about the existence of the preexisting
IRQF_SAMPLE_RANDOM flag.  I've opted to keep this patch conservative and
let it continue to exist until the flag gets officially purged from the
kernel.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch creates a per-interrupt data structure, moves the napi
member over, and creates a tg3 pointer back to the device structure.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Later patches will be adding MSIX support, which will complicate
interrupt initialization.  This patch prepares for the integration by
breaking out the interrupt setup and teardown code into separate
functions and cleaning up the error return paths.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5717 only uses extended buffer descriptors for the jumbo producer
ring.  Extended buffer descriptors are available on all devices that
support a separate jumbo producer ring so make the change universal.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch migrates most of the rx producer ring variables to a new
tg3_rx_prodring_set structure and modifies the code accordingly.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Later patches are going to complicate the ring initialization routines.
This patch breaks out the setup and teardown of the rx producer rings
into separate functions to make the code more readable.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves where the jumbo capable and msi support flags are
located.  This is prep work for the addition of msix support flags.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch separates the code that sets up the mini producer ring from
the code that sets up the jumbo producer rings.  The 5717 asic rev
devices do not have a mini ring, but do have a jumbo frame
implementation similar to the 5704 and previous devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes up the NVRAM detection switch statements to conform
to the kernel coding style.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device firmware uses the MDIO bus during early setup.  If the driver
modifies the MDIO bus configuration while it is in use by the firmware,
any number of bad things can happen.  This patch delays MDIO setup until
after the firmware posts its magic signature, signifying initialization
is complete.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the bearer_priority to be less than TIPC_MIN_LINK_PRI and greater than
TIPC_MAX_LINK_PRI is logically impossible.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

create_proc_read_entry() is going to be removed soon.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
 - no_ether_link          : If set to 1, do not use ETHER_LINK
 - ether_link_active_low  : If set to 1, ETHER_LINK is active low.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On TI's DA850/OMAP-L138 EVM, MAC address is stored in SPI
flash which is accessed using MTD interface.

This patch delays the initialization of DaVinci EMAC driver
by changing module_init to late_initcall. This helps SPI and
MTD drivers to get initialized before EMAC thereby enabling
EMAC driver to read the MAC address while booting and use it.

Tested with NFS on DM644x, DM6467, DA830/OMAP-L137 and
DA850/OMAP-L138 EVMs.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix lmc_proto_type() invocation.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NJens Rosenboom <jens@mcbone.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the copy of the MD5 authentication key from tcp_check_req().
This key has already been copied by tcp_v4_syn_recv_sock() or
tcp_v6_syn_recv_sock().
Signed-off-by: NJohn Dykstra <john.dykstra1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Maintain a per-qdisc bitmap for pfifo_fast giving  availability
of skbs for each band. This allows faster lookup for a skb when
there are no high priority skbs. Also, it helps in (rare) cases
when there are no skbs on the list, where an immediate lookup is
faster than iterating through the three bands.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When processing a received IPv6 Router Advertisement, the kernel
creates or updates an IPv6 Neighbor Cache entry for the sender --
but presently this does not occur if IPv6 forwarding is enabled
(net.ipv6.conf.*.forwarding = 1), or if IPv6 Router Advertisements
are not accepted (net.ipv6.conf.*.accept_ra = 0), because in these
cases processing of the Router Advertisement has already halted.

This patch allows the Neighbor Cache to be updated in these cases,
while still avoiding any modification to routes or link parameters.

This continues to satisfy RFC 4861, since any entry created in the
Neighbor Cache as the result of a received Router Advertisement is
still placed in the STALE state.
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Better small packet receive performance.
- Better handling of Flow control on 5709.
- Fixed iSCSI TMP ABORT TASK problem.
- Added iSCSI TCP timestamp option.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>