Add a new operation to disable the DA, SA and VTU priority override.

Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.

Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new operation to disable the limiting of learnt MAC addresses.

Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.

Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).

Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".

The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).

Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.

Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.

Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.

Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.

Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.

Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.

All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".

This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a mv88e6xxx_port_mask() helper to get the bitmask of ports in a
switch chip, that will be used in several features.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the ops needed to support the watchdog for the MV88E6390
family.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch contains a watchdog looking for issues with the internal
gubbins of the switch. Hook the interrupt the watchdog triggers and
log the value of the control register indicating why the watchdog
fired. The watchdog can only be cleared with a switch reset, which
will destroy the current configuration. Rather than doing this, just
disable the interrupt.

The mv88e6390 family has different watchdog registers. So use an ops
structure, so support for the mv88e6390 family can be added later.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel.  There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.

Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.

This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move it out from the middle for the #defines to just before it is
needed.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 MDIO bus controllers can support for clause 45 accesses.
The internal SERDES interfaces need this, and it is likely external
10GHz PHYs will be clause 45.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().

Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().

The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.

When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.

When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.

At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.

It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family
88E6352 and switches of family 88E6390.

This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With all the infrastructure in place, implement access to the external
MDIO bus on the 6390 family.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 has multiple MDIO busses. Generalize the parsing of the
device tree to support multiple mdio nodes. The external mdio bus has
a compatible strings to indicate it is external.

Keep a linked list of busses, placing the external mdio bus at the
tail of the list. When within the driver an mdio bus is needed,
e.g. for EEE or SERDES, use the head of the list which should be the
internal bus.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have the MDIO bus driver code allocate a private structure and make
the chip a member of it. This will allow us to add further members in
the future.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for supporting multiple MDIO busses, pass the mii_bus
structure to all PHY operations. It will in future then be clear on
which MDIO bus the operation should be performed.

For reads/write from phylib, the mii_bus is readily available. However
some internal code also access the PHY, e.g. for EEE and SERDES. Make
this code use the one and only currently available MDIO bus.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 6352 chip has a 8-bit address/16-bit data EEPROM access.
The Marvell 6390 chip has a 16-bit address/8-bit data EEPROM access.

This patch implements the 8-bit data EEPROM access in the mv88e6xxx
driver and adds its support to chips of the 6390 family.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This chip needs MV88E6XXX_FLAG_G2_INT
Signed-off-by: NVolodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Marvell chips can enable/disable the PPU on demand. This is needed
to access the PHY registers when there is no indirection mechanism.

Add two new ppu_enable and ppu_disable ops to describe this and finally
get rid of the MV88E6XXX_FLAG_PPU* flags.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell chips have different way to issue a software reset.

Old chips (such as 88E6060) have a reset bit in an ATU control register.

Newer chips moved this bit in a Global control register. Chips with
controllable PPU should reset the PPU when resetting the switch.

Add a new reset operation to implement these differences and introduce a
mv88e6xxx_software_reset() helper to wrap it conveniently.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 has a number flow control registers accessed via the
Flow Control register. Use these to set the pause control.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 has a different mechanism for configuring pause.
Refactor the code into an ops function, and for the moment, don't add
any mv88e6390 code yet.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two different rate limiting configurations, depending on the
switch generation. Refactor this into ops.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some switches support jumbo frames. Refactor this code into operations
in the ops structure.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older chips only support DSA tagging. Newer chips have both DSA and
EDSA tagging. Refactor the code by adding port functions for setting the
frame mode, egress mode, and if to forward unknown frames.

This results in the helper mv88e6xxx_6065_family() becoming unused, so
remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older chips support a single tagging protocol, DSA. New chips support
both DSA and EDSA, an enhanced version. Having both as an option
changes the register layouts. Up until now, it has been assumed that
if EDSA is supported, it will be used. Hence the register layout has
been determined by which protocol should be used. However, mv88e6390
has a different implementation of EDSA, which requires we need to use
the DSA tagging. Hence separate the selection of the protocol from the
register layout.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 changes the monitor control register into the Monitor
and Management control, which is an indirection register to various
registers.

Add ops to set the CPU port and the ingress/egress port for both
register layouts, to global1
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 does not have the two registers to set the frame
priority map. Instead it has an indirection registers for setting a
number of different priority maps. Refactor the old code into an
function, implement the mv88e6390 version, and use an op to call the
right one.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: NStefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v2:
  Rename functions to avoid _ prefix.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>