Bit more than minimal conversion. There might be some issues because
of qlcnic_set_netdev_features() if it's called after netdev init.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.

Fixing it by pulling extra frags.

Cc: stable@kernel.org
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert driver to use new ethtool set_phys_id.
Not completely sure that this is correct for all cases of device
up/down and doing operation. Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bumped up version number to 5.0.16
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o In dev->open LRO was enabled by default, enable it depending
  upon netdev->features , kernel may have disabled it.
o Configure LRO when interface is up.
Signed-off-by: NRajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: NAnirban Chakraborty <Anirban.Chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use flash layout table to get flash fw starting address and its size.
If that fails, use legacy method.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleaned up unused codes for interrupt coalescence settings
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Made changes to VLAN code comply with new VLAN infrastructure in kernel
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimized code resulted in achieving lower CPU utilization on transmit path
and higher throughput for small packet sizes (64 bytes).
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 1. Changed adapter structure to move away from embedding hardware and
    receive context structs and use pointers to those objects
 2. Packed all the structs that interface with FW
 3. Removed unused code and structs
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a memory leak in error path of pci info.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this fix, PCI info was available only when multiple NIC functions
are present on the same port.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit d5dbda23 "ethtool: Add
support for vlan accleration.", drivers that have NETIF_F_HW_VLAN_TX,
and/or NETIF_F_HW_VLAN_RX feature, but do not allow enable/disable vlan
acceleration via ethtool set_flags, always return -EINVAL from that
function. Fix by returning -EINVAL only if requested features do not
match current settings and can not be changed by driver.

Change any driver that define ethtool->set_flags to use
ethtool_invalid_flags() to avoid similar problems in the future
(also on drivers that do not have the problem).

Tested with modified (to reproduce this bug) myri10ge driver.

Cc: stable@kernel.org # 2.6.37+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Max rx queues and tx queues are governed by fimware.
So driver should not validate these values.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Remove checks of 1 for auto_fw_reset module parameter.
  auto_fw_reset is of type int and can have value > 1.
o Remove unnecessary #define for 1
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Updating module parameter after driver load is not supported
  except auto_fw_reset parameter. Changing these parameter after
  driver load, can have weird result.

o Update driver version to 5.0.15.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQ diag test was getting executed only when both register test
and link test passed. The test should get executed if ETH_TEST_FL_OFFLINE
flag is set.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver is reading flash fw version from defined address, this address
may be invalid. Indeed Driver should read address for fw version through
flash layout table. Flash layout table has defined region and address for
fw version address should be read from fw image region.

Driver has check for old firmware, this bug can cause driver load fail.
This patch will try to read fw version from flash image region, if that fails,
read from defined address.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: NJoe Perches <joe@perches.com>

Some boot code drivers dont have cleanup routine, so pci function
remains in unknown state prior to driver load. So during driver load
issue FLR unconditionally.

Update driver version to 5.0.14.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OCM window register offset was calculated incorrectly for
pci function greater than zero.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When interface is down, create temporary context to config LED.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently driver set default eswitch configuration values for PF function,
instead of validating values sent by application.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Loopback mode can not be supported in CNA mode. Removing it until FW is fixed.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In kdump environment do not depend upon reset_devices parameter
to reset the pci function as this parameter may become obsolete.
Instead use an adapter specific mechanism to determine if the pci
function needs to be reset.

Per function refcount is maintained in driver, which is set in probe
and reset in remove handler of adapter. If the probe detects the count
as non zero then reset the function.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log LRO off message while disabling rx checksum only when
LRO is already enabled.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add description for CN1000Q adapter
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of kdump environment the function may be in unknown state.
Reset the function using PCI FLR before initializing it.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow minimum bandwidth to be set zero
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Its now illegal to call netif_stop_queue() before register_netdev()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

4095 vlan id is reserved and should not be use.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If eswitch is enabled, rcv ring size can be reduce, as
physical port is partition-ed.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In failover bonding case, same mac address can be programmed on other slave function.
Fw will delete old entry (original func) associated with that mac address.
Need to reporgram mac address, if failover again happen to original function.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added statistics for Nic Partition supported adapter.
These statistics are maintined in device.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>