We move the display-specific code into it's own functions, called
from the general GPU state save/restore functions. This will be needed
later by the GPU reset code.
Signed-off-by: NBen Gamari <bgamari.foss@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch adds framebuffer compression (good for about ~0.5W power
savings in the best case) support for pre-GM45 chips.  GM45+ have a new,
more flexible FBC scheme that will be added in a separate patch.

FBC can't always be enabled: the compressed buffer must be physically
contiguous and reside in stolen space.  So if you have a large display
and a small amount of stolen memory, you may not be able to take
advantage of FBC.  In some cases, a BIOS setting controls how much
stolen space is available.  Increasing this to 8 or 16M can help.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Some laptop platforms will disable pipes and/or planes at lid close time
and not restore them when the lid is opened again.  So catch the lid
event, and if the lid was opened, force a mode restore.

Fixes fdo bug #21230.
Acked-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Test on the IGD chip, which is a G33-like graphic device.
Signed-off-by: NLi Peng <peng.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NFabian Henze <hoacha@quantentunnel.de>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The driver gets the bridge device in a number of places, upcoming
vga arb code paths need the bridge device, however they need it in
under a lock, and the pci lookup can allocate memory. So clean
this code up before then and get the bridge once for the driver lifetime.
Signed-off-by: NDave Airlie <airlied@redhat.com>

According to the docs, the ringbuffer is not allowed to wrap in the middle
of an instruction.

G45 PRM, Vol 1b, p101:
  While the “free space” wrap may allow commands to be wrapped around the
  end of the Ring Buffer, the wrap should only occur between commands.
  Padding (with NOP) may be required to follow this restriction.

Do as commanded.

[Having seen bug reports where there is evidence of split commands, but
apparently the GPU has continued on merrily before a bizarre and untimely
death, this may or may not fix a few random hangs.]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
CC: Eric Anholt <eric@anholt.net>
Signed-off-by: NEric Anholt <eric@anholt.net>

There are several sources of unnecessary power consumption on Intel
graphics systems. The first is the LVDS clock. TFTs don't suffer from
persistence issues like CRTs, and so we can reduce the LVDS refresh rate
when the screen is idle. It will be automatically upclocked when
userspace triggers graphical activity. Beyond that, we can enable memory
self refresh. This allows the memory to go into a lower power state when
the graphics are idle. Finally, we can drop some clocks on the gpu
itself. All of these things can be reenabled between frames when GPU
activity is triggered, and so there should be no user visible graphical
changes.
Signed-off-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NBen Gamari <bgamari.foss@gmail.com>
[anholt: hand-applied for conflicts]
Signed-off-by: NEric Anholt <eric@anholt.net>

Use VBT information to determine which DDC bus to use for CRTDCC.
Fall back to GPIOA if VBT info is not available.
Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>
Tested on: 855 (David), and 945GM, 965GM, GM45, and G45 (anholt)

The lack of a proper LRU was partially worked around by taking the fence
from the object containing the oldest seqno.  But if there are multiple
objects inactive, then they don't have seqnos and the first fence reg
among them would be chosen.  If you were trying to copy data between two
mappings, this could result in each page fault stealing the fence from
the other argument, and your application hanging.

https://bugs.freedesktop.org/show_bug.cgi?id=23566
https://bugs.freedesktop.org/show_bug.cgi?id=23220
https://bugs.freedesktop.org/show_bug.cgi?id=23253
https://bugs.freedesktop.org/show_bug.cgi?id=23366

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NEric Anholt <eric@anholt.net>

This adds embedded DisplayPort support on next mobile chip which
aims to replace origin LVDS port. VBT's driver feature block has
been used to determine the type of current internal panel for eDP
or LVDS.

Currently no panel fitting support for eDP and backlight control
would be added in future.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch refactors the existing error detection and collection code,
placing most of it in i915_handle_error(). Additionally, we introduce a
work queue for scheduling post-crash tasks such as generating a uevent.
Using the uevent facility, userspace should be able to capture a
post-mortem dump for diagnostics.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NBen Gamari <bgamari.foss@gmail.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

As of 52dc7d32, we could leave an old
linear GTT mapping in place, so that apps trying to GTT-mapped write in
tiled data wouldn't get the fence added, and garbage would get displayed.
Signed-off-by: NEric Anholt <eric@anholt.net>

This wasn't even used as far as I could tell and will only confuse
people (like me).
Signed-off-by: NBen Gamari <bgamari.foss@gmail.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch from jbarnes and myself adds FIFO watermark control to the
driver.  This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.

It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch enables error detection by enabling several types of error
interrupts.  When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.).  The new
record is then available from sysfs.  The current code will also dump
the error state to the system log.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NKeith Packard <keithp@keithp.com>

The fence register value also depends upon the stride of the object, so we
need to clear the fence if that is changed as well.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[anholt: Added 8xx and 965 paths, and renamed the confusing
i915_gem_object_tiling_ok function to i915_gem_object_fence_offset_ok]
Signed-off-by: NEric Anholt <eric@anholt.net>

With the work by Jesse Barnes to eliminate allocation of fences during
execbuffer, it becomes possible to write to the scan-out buffer with it
never acquiring a fence (simply by only ever writing to the object using
tiled GPU commands and never writing to it via the GTT). So for pre-i965
chipsets which require fenced access for tiled scan-out buffers, we need
to obtain a fence register.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

Update interrupt handling methods for IGDNG with new registers
for display and graphics interrupt functions. As we won't use
irq-based vblank sync in dri2, so display interrupt on new chip
will be used for hotplug only in future.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Using the new PNP resource checking code, this patch allows the i915
driver to allocate MCHBAR space if needed and use the BAR to determine
current memory settings.

[apw@canonical.com: moved to the new generic PNP resource interface]
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

failure to update-index after git-am --reject to hand-apply
Signed-off-by: NEric Anholt <eric@anholt.net>

The general definition block contains the child device tables, which include
the SDVO device info. For example: device slave address, device dvo port,
device type.

We will get the info of SDVO device by parsing the general definition blocks.
Only when a valid slave address is found, it is regarded as the SDVO device.
And the info of DVO port and slave address is recorded.

http://bugs.freedesktop.org/show_bug.cgi?id=20429Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
[anholt: dropped drm_pciids.h hunk to avoid loading an incomplete driver]
Signed-off-by: NEric Anholt <eric@anholt.net>

keithp didn't like the original 20ms plan because a cooperative client could
be starved by an uncooperative client.  There may even have been problems
with cooperative clients versus cooperative clients.  So keithp changed
throttle to just wait for the second to last seqno emitted by that client.
It worked well, until we started getting more round-trips to the server
due to DRI2 -- the server throttles in BlockHandler, and so if you did more
than one round trip after finishing your frame, you'd end up unintentionally
syncing to the swap.

Fix this by keeping track of the client's requests, so the client can wait
when it has an outstanding request over 20ms old.  This should have
non-starving behavior, good behavior in the presence of restarts, and less
waiting.  Improves high-settings openarena performance on my GM45 by 50%.
Signed-off-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This may fix cursor corruption in X on resume, which would persist until
the cursor was hidden and then shown again.

V2: Also include the cursor control regs.
Signed-off-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NMa Ling <ling.ma@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

It fixed bug #21659
Signed-off-by: NMa Ling <ling.ma@intel.com>
[anholt: hand-applied because git-am is too picky]
Signed-off-by: NEric Anholt <eric@anholt.net>

This makes software fallbacks not do tiling wrong on i965 and later after
resume. It also should fix 945 performance reduction after resume which
would have disabled tiling without causing any visible effect.
Signed-off-by: NKeith Packard <keithp@keithp.com>
[anholt: Fixed up the 915 case to not save/restore the new regs]
Signed-off-by: NEric Anholt <eric@anholt.net>

i386 has inline code for writeq and readq, so just use those instead of ugly
macros which evaluate arguments multiple times.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This had been delayed for some time due to failure to work on the one piece
of G41 hardware we had, and lack of success reports from anybody else.
Current hardware appears to be OK.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: hand-applied due to conflicts with IGD patches]
Signed-off-by: NEric Anholt <eric@anholt.net>

The i915 DRM triggers registration of the ACPI video driver on load. It
should unregister it at unload in order to avoid generating backtraces on
being reloaded.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Save the bit 17 state of the pages when freeing the page list, and
reswizzle them if necessary when rebinding the pages (in case they were
swapped out).  Since we have userland with expectations that the swizzle
enums let it pread and pwrite contents accurately, we can't expose a new
swizzle enum for bit 17 (which it would have to GTT map to handle), so we
handle it down in pread and pwrite by swizzling the copy when bit 17 of the
page address is set.
Signed-off-by: NEric Anholt <eric@anholt.net>

We create a debugfs node (i915_ringbuffer_data) to expose a hex dump
of the ring buffer itself.  We also expose another debugfs node
(i915_ringbuffer_info) with information on the state (i.e. head, tail
addresses) of the ringbuffer.

For batchbuffer dumping, we look at the device's active_list, dumping
each object which has I915_GEM_DOMAIN_COMMAND in its read
domains. This is all exposed through the dri/i915_batchbuffers debugfs
file with a header for each object (giving the objects gtt_offset so
that it can be matched against the offset given in the
BATCH_BUFFER_START command.
Signed-off-by: NBen Gamari <bgamari@gmail.com>
Signed-off-by: NCarl Worth <cworth@cworth.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

This is a baby-step in the direction of having finer-grained
locking than the struct_mutex. Specifically, this will enable
new debugging code to read the active list for printing out
GPU state when the GPU is wedged, (while the struct_mutex is
held, of course).
Signed-off-by: NCarl Worth <cworth@cworth.org>
[anholt: indentation fix]
Signed-off-by: NEric Anholt <eric@anholt.net>

Add VGA port hotplug detection to the i915 driver.  When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: NEric Anholt <eric@anholt.net>

drivers/gpu/drm/i915/i915_drv.c:102: error: too many arguments to
function ‘intel_opregion_init’
Signed-off-by: NLen Brown <len.brown@intel.com>

Intel graphics hardware that implements the ACPI IGD OpRegion spec
requires that the list of display devices be populated before any ACPI
video methods are called. Detect when this is the case and defer
registration until the opregion code calls it. Fixes crashes on HP
laptops.

http://bugzilla.kernel.org/show_bug.cgi?id=11259Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NLen Brown <len.brown@intel.com>