Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 23 10月, 2010 7 次提交
  3. 16 10月, 2010 1 次提交
    • O
      mmc: sdio: fix SDIO suspend/resume regression · 1c8cf9c9
      由 Ohad Ben-Cohen 提交于 
      Fix SDIO suspend/resume regression introduced by 4c2ef25f "mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume":

  PM: Syncing filesystems ... done.
  Freezing user space processes ... (elapsed 0.01 seconds) done.
  Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
  Suspending console(s) (use no_console_suspend to debug)
  pm_op(): platform_pm_suspend+0x0/0x5c returns -38
  PM: Device pxa2xx-mci.0 failed to suspend: error -38
  PM: Some devices failed to suspend

4c2ef25f moved the card removal/insertion mechanism out of MMC's
suspend/resume path and into pm notifiers (mmc_pm_notify), and that
broke SDIO's expectation that mmc_suspend_host() will remove the card,
and squash the error, in case -ENOSYS is returned from the bus suspend
handler (mmc_sdio_suspend() in this case).

mmc_sdio_suspend() is using this whenever at least one of the card's SDIO
function drivers does not have suspend/resume handlers - in that case
it is agreed to force removal of the entire card.

This patch fixes this regression by trivially bringing back that part of
mmc_suspend_host(), which was removed by 4c2ef25f.
Reported-and-tested-by: NSven Neumann <s.neumann@raumfeld.com>
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: <stable@kernel.org>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Signed-off-by: NChris Ball <cjb@laptop.org>
      1c8cf9c9
  5. 12 8月, 2010 1 次提交
    • A
      mmc: add erase, secure erase, trim and secure trim operations · dfe86cba
      由 Adrian Hunter 提交于 
      SD/MMC cards tend to support an erase operation.  In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.

SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.

"erase_size" is the minimum size, in bytes, of an erase operation.  For
MMC, "erase_size" is the erase group size reported by the card.  Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector.  For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.

SD/MMC cards can erase an arbitrarily large area up to and
including the whole card.  When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:

    1. A single erase command will make all other I/O on the card
       wait.  This is not a problem if the whole card is being erased, but
       erasing one partition will make I/O for another partition on the
       same card wait for the duration of the erase - which could be a
       several minutes.

    2. To be able to inform the user of erase progress.

    3. The erase timeout becomes too large to be very useful.
       Because the erase timeout contains a margin which is multiplied by
       the size of the erase area, the value can end up being several
       minutes for large areas.

"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.

For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.

For SD, "preferred_erase_size" is the allocation unit size specified by
the card.

"preferred_erase_size" is in bytes.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NJens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      dfe86cba
  7. 11 8月, 2010 2 次提交
  9. 28 5月, 2010 1 次提交
  11. 13 3月, 2010 1 次提交
  13. 07 3月, 2010 1 次提交
    • N
      sdio: introduce API for special power management features · da68c4eb
      由 Nicolas Pitre 提交于 
      This patch series provides the core changes needed to allow SDIO cards to
remain powered and active while the host system is suspended, and let them
wake up the host system when needed.  This is used to implement
wake-on-lan with SDIO wireless cards at the moment.  Patches to add that
support to the libertas driver will be posted separately.

This patch:

Some SDIO cards have the ability to keep on running autonomously when the
host system is suspended, and wake it up when needed.  This however
requires that the host controller preserve power to the card, and
configure itself appropriately for wake-up.

There is however 4 layers of abstractions involved: the host controller
driver, the MMC core code, the SDIO card management code, and the actual
SDIO function driver.  To make things simple and manageable, host drivers
must advertise their PM capabilities with a feature bitmask, then function
drivers can query and set those features from their suspend method.  Then
each layer in the suspend call chain is expected to act upon those bits
accordingly.

[akpm@linux-foundation.org: fix typo in comment]
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      da68c4eb
  15. 16 12月, 2009 1 次提交
    • B
      mmc: add module parameter to set whether cards are assumed removable · bd68e083
      由 Ben Hutchings 提交于 
      Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.

In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend.  So there are
two possible behaviours, each of which will cause data loss in some cases:

CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend.  Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.

CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend.  They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.

Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      bd68e083
  17. 23 9月, 2009 7 次提交
  19. 14 6月, 2009 2 次提交
    • S
      MMC core: limit minimum initialization frequency to 400kHz · 8dfd0374
      由 Sascha Hauer 提交于 
      Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
      8dfd0374
    • J
      mmc: mmc_rescan detects card change in one run · 94d89efb
      由 Jorg Schummer 提交于 
      With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.

This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: NJorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>
      94d89efb
  21. 04 5月, 2009 1 次提交
  23. 31 3月, 2009 1 次提交
  25. 25 3月, 2009 3 次提交
  27. 01 1月, 2009 2 次提交
  29. 09 11月, 2008 1 次提交
  31. 02 8月, 2008 1 次提交
  33. 15 7月, 2008 2 次提交
    • P
      mmc,sdio: helper function for transfer padding · ad3868b2
      由 Pierre Ossman 提交于 
      There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.

A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      ad3868b2
    • A
      mmc: add support for card-detection polling · 28f52482
      由 Anton Vorontsov 提交于 
      Some hosts (and boards that use mmc_spi) do not use interrupts on the CD
line, so they can't trigger mmc_detect_change. We want to poll the card
and see if there was a change. 1 second poll interval seems resonable.

This patch also implements .get_cd() host operation, that could be used
by the hosts that are able to report card-detect status without need to
talk MMC.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      28f52482
  35. 19 4月, 2008 2 次提交
  37. 02 11月, 2007 1 次提交
  39. 24 9月, 2007 2 次提交
    • P
      mmc: add led trigger · af8350c7
      由 Pierre Ossman 提交于 
      Add a led trigger for each host controller that indicates if there
is a request active on the controller.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      af8350c7
    • D
      MMC core learns about SPI · af517150
      由 David Brownell 提交于 
      Teach the MMC/SD/SDIO core about using SPI mode.

 - Use mmc_host_is_spi() so enumeration works through SPI signaling
   and protocols, not just the native versions.

 - Provide the SPI response type flags with each request issued,
   including requests from the new lock/unlock code.

 - Understand that cmd->resp[0] and mmc_get_status() results for SPI
   return different values than for "native" MMC/SD protocol; this
   affects resetting, checking card lock status, and some others.

 - Understand that some commands act a bit differently ... notably:
     * OP_COND command doesn't return the OCR
     * APP_CMD status doesn't have an R1_APP_CMD analogue

Those changes required some new and updated primitives:

 - Provide utilities to access two SPI-only requests, and one
   request that wasn't previously needed:
     * mmc_spi_read_ocr() ... SPI only
     * mmc_spi_set_crc() ... SPI only (override by module parm)
     * mmc_send_cid() ... for use without broadcast mode

 - Updated internal routines:
     * Previous mmc_send_csd() modified into mmc_send_cxd_native();
       it uses native "R2" responses, which include 16 bytes of data.
     * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
       helper for command-and-data access
     * Bugfix to that mmc_send_cxd_data() code:  dma-to-stack is
       unsafe/nonportable, so kmalloc a bounce buffer instead.

 - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper

 - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
   those helper routines based on whether they're native or SPI

The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI:  MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      af517150