The mode should be stored and used per virtual interface. Remove
the mode from device global structure and rework the code to use
the mode from brcmf_cfg80211_vif.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This attribute indicates successful IBSS or AP connection has been
established. However, this no longer works for virtual interfaces.
As it turns out this attribute is identical to the CONNECTED bit
in struct brcmf_cfg80211_vif::sme_state. This patch removes the
attribute and rework some functions relying on it.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for 4313 iPA variant.
It is a variant of already supported 4313 ePA
and needs some PHY changes to work properly.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move functions in
preparation for 4313iPA changes
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Put basic information about hardware in debugfs.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcms_b_txstatus and brcms_b_recv are off by one when
doing bounds checking on number of packets to process
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcms_c_isr returns true if interrupt was for us
and if dpc should be scheduled which is the same thing.
Simplify it.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The .tx() callback function can drop packets when there is no
space in the DMA fifo. Propagate that information to caller
and make sure the freed sk_buff reference is not accessed.
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Organizational changes need to be reflected in the MAINTAINERS file.
The contact info on wireless.kernel.org has also been updated.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are 2 different things:
- sub-menu for "Atheros Wireless cards" family
- module ath.ko with common Atheros code

Until now, they both used to depend on the same Kconfig variable ATH_COMMON.
Thus, being "Atheros card" and "depending on ath.ko" was the same.

To allow module to belong to the
"Atheros Wireless cards" family but not use ath.ko,
2 conditions above need to be separated.

So, this patch introduce new Kconfig variable ATH_CARDS for belonging
to the "Atheros Wireless Cards" family; while ATH_COMMON becomes hidden
variable to express dependency on common Atheros code in ath.ko. Modules
that depend on this common code now express it by setting ATH_COMMON.

Right now, ath6kl do not depend on common code and thus do not set ATH_COMMON.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'bf_next' is cleared using ATH_TXBUF_RESET() in both the
callsites of ath_tx_get_buffer().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ethtool statistics are available only when
CONFIG_ATH9K_DEBUGFS is enabled, move these functions
to debug.c
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NPetr Stetiar <ynezz@true.cz>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for advertising GreenField, 40MHz intolerance
or LDPC coding support to cfg80211.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: stomp audio profiles on weak signal
strength" failed to take care of new stomp type while
programming concurrent tx priority. That leads to array
index out of bounds access.

drivers/net/wireless/ath/ath9k/btcoex.c:414
        ath9k_hw_btcoex_set_concur_txprio()
               error: buffer overflow 'stomp_txprio' 4 <= 4
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If CONFIG_SSB_EMBEDDED or CONFIG_SSB_DRIVER_MIPS is set and
CONFIG_SSB_DRIVER_EXTIF is not set, it will cause compile problems
because of missing functions. This patch fixes these problems.

The mips driver now also uses ssb_chipco_available() instead of
checking bus->chipco.dev manually.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the following warning:

  CC      drivers/bcma/driver_pci_host.o
drivers/bcma/driver_pci_host.c: In function 'bcma_core_pci_fixup_addresses':
drivers/bcma/driver_pci_host.c:555:23: error: ignoring return value of
'pci_assign_resource', declared with attribute warn_unused_result
[-Werror=unused-result]
Reported-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LMAC API states that the TSF clock value of
every rx'ed frame is a "usec accurate timestamp
of the hardware clock at the end of frame
(before OFDM SIFS EOF padding)".
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding __printf helps spot format and argument mismatches.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some cases, e.g. probe_status, there were spaces
missing so the trace output was confusing. Also make
it more like mac80211 when printing netdevs/wiphys
to make reading a combined log easier.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The frequencies will be printed when actually
doing the scan, and the IEs can be captured
on the hwsim0 monitor.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the number of channels is > 1, which means that
hwsim will use mac80211 channel contexts, it can
also advertise VHT support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add definitions for the VHT MCS support values that
are used to indicate, for each number of streams
(1 through 8) which MCSes are supported.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support to mac80211 for having drivers report
received VHT MCS information.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for reporting and calculating VHT MCSes.

Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.

Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)

This also adds new helper functions:
 - cfg80211_chandef_create to create a channel def
   struct given the control channel and channel type,
 - cfg80211_chandef_identical to check if two channel
   definitions are identical
 - cfg80211_chandef_compatible to check if the given
   channel definitions are compatible, and return the
   wider of the two

This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
 - regulatory checks on the usable bandwidth (if that
   even makes sense)
 - regulatory TX power (database can't deal with it)
 - a proper channel compatibility calculation for the
   new channel types
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If ieee80211_prep_channel() decides that HT should be
disabled (because the HT IEs from the AP were invalid)
it will set the IEEE80211_STA_DISABLE_HT to not send
HT capabilities to the AP when associating. If this
happens during authentication, the flag will be lost
and we send HT frames, even if the channel config was
set up for non-HT. This can lead to issues.

Fix this by always resetting the ifmgd flags to zero
when the channel context is released so that the flag
resetting in ieee80211_mgd_assoc() isn't necessary.

To make the code a bit easier move the call to release
the channel in ieee80211_set_disassoc() to the end of
the function together with the flag resetting (which
needs to be at the end to avoid timers setting flags.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use shortcut pointer instead where it is appropriate.
Signed-off-by: NMarco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Return early if not a QoS Data frame.
Give proper documentation.
Signed-off-by: NMarco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>