Allow rewriting of a file and extending a file upto the end of the
allocated block on a full filesystem.

From: Chris Mason <mason@suse.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patches adds the "nbds_max" parameter to the nbd kernel module, which
limits the number of nbds allocated.  Previously, always all 128 entries
were allocated unconditionally, which used to waste resources and
needlessly flood the hotplug system with events.  (Defaults to 16 now.)
Signed-off-by: NLars Marowsky-Bree <lmb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add EOWNERDEAD and ENOTRECOVERABLE to all architectures.  This is to
support the upcoming patches for robust mutexes.

We normally don't reserve parts of the name/number space for external
patches, but robust mutexes are sufficiently popular and important to
justify it in this case.
Signed-off-by: NJoe Korty <joe.korty@ccur.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Profiling hit rates on merging shows that the last merge hint works
extremely well for most work loads.  So lets kill the linear merge scan in
noop-iosched, so it provides O(1) run time for any operation.

Testing credits go to Ken Chen from Intel.
Signed-off-by: NJens Axboe <axboe@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

kallsyms does not consider SYMBOL_PREFIX of C.  Consequently it does not
work on architectures using that prefix character (h8300, v850).
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is take two of a patch that should have appeared two days ago, before
yesterday's "remote control" patch for the same card.

This patch sets unconnected GPIO to Output to keep them from floating (just
good driver writing practice, being nice to the chip), and uses GPIO16 to
switch TV vs.  FM - this pin switches inputs onto the tuner, as well as the
audio output from the tuner into the 7135 SIF input.  Consequently, FM
radio support is being un-commented because it's now working (sort of, see
below).

These two patches get the card almost fully operational; there appears to
be a bug in tda8290.c remaining that puts an offset onto the tuned
frequency in FM radio mode.  We're investigating.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Subject says it ...  this card's IR microcontroller design and attachment
are compatible to the company's previous designs, so the patch was as
simple as it gets.
DESC
LifeView FlyTV Platinum FM: GPIO usage
EDESC
From: Peter Missel <peter.missel@onlinehome.de>

This is take two of a patch that should have appeared two days ago, before
yesterday's "remote control" patch for the same card.

This patch sets unconnected GPIO to Output to keep them from floating (just
good driver writing practice, being nice to the chip), and uses GPIO16 to
switch TV vs.  FM - this pin switches inputs onto the tuner, as well as the
audio output from the tuner into the 7135 SIF input.  Consequently, FM
radio support is being un-commented because it's now working (sort of, see
below).

These two patches get the card almost fully operational; there appears to
be a bug in tda8290.c remaining that puts an offset onto the tuned
frequency in FM radio mode.  We're investigating.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It's trivial for the resize option to auto-get the underlying device size,
while it's harder for the user.  I've copied the code from jfs.

Since of the different reiserfs option parser (which does not use the
superior match_token used by almost every other filesystem), I've had to
use the "resize=auto" and not "resize" option to specify this behaviour.
Changing the option parser to the kernel one wouldn't be bad but I've no
time to do this cleanup in this moment.

Btw, the mount(8) man page should be updated to include this option.  Cc
the relevant people, please (I hope I cc'ed the right people).

Cc: <reiserfs-dev@namesys.com>
Cc: <reiserfs-list@namesys.com>
Cc: <mtk-manpages@gmx.net>
Cc: Alex Zarochentsev <zam@namesys.com>
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update the RCU documentation to allow for the new synchronize_rcu() and
synchronize_sched() primitives.  Fix a few other nits as well.
Signed-off-by: NPaul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: NPaul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The synchronize_kernel() primitive is used for quite a few different purposes:
waiting for RCU readers, waiting for NMIs, waiting for interrupts, and so on.
This makes RCU code harder to read, since synchronize_kernel() might or might
not have matching rcu_read_lock()s.  This patch creates a new
synchronize_rcu() that is to be used for RCU readers and a new
synchronize_sched() that is used for the rest.  These two new primitives
currently have the same implementation, but this is might well change with
additional real-time support.  Both new primitives are GPL-only, the old
primitive is deprecated.
Signed-off-by: NPaul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a deprecated_for_modules macro that allows symbols to be deprecated only
when used by modules, as suggested by Andrew Morton some months back.
Signed-off-by: NPaul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The gpl exports need to be put back.  Moving them to GPL -- but in a
measured manner, as I proposed on this list some months ago -- is fine.
Changing these particular exports precipitously is most definitely -not-
fine.  Here is my earlier proposal:

	http://marc.theaimsgroup.com/?l=linux-kernel&m=110520930301813&w=2

See below for a patch that puts the exports back, along with an updated
version of my earlier patch that starts the process of moving them to GPL.
I will also be following this message with RFC patches that introduce two
(EXPORT_SYMBOL_GPL) interfaces to replace synchronize_kernel(), which then
becomes deprecated.

Signed-off-by: <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The current logic assumes that a /proc/<PID>/task directory should have a
hardlink count of 3, probably counting ".", "..", and a directory for a
single child task.

It's fairly obvious that this doesn't work out correctly when a PID has
more than one child task, which is quite often the case.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The pid directories in /proc/ currently return the wrong hardlink count - 3,
when there are actually 4 : ".", "..", "fd", and "task".

This is easy to notice using find(1):
	cd /proc/<pid>
	find

In the output, you'll see a message similar to:

find: WARNING: Hard link count is wrong for .: this may be a bug in your
filesystem driver.  Automatically turning on find's -noleaf option.
Earlier results may have failed to include directories that should have
been searched.

http://bugs.gentoo.org/show_bug.cgi?id=86031

I also noticed that CONFIG_SECURITY can add a 5th: attr, and performed a
similar fix on the task directories too.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The attached patch moves the IRQ-related SA_xxx flags (namely, SA_PROBE,
SA_SAMPLE_RANDOM and SA_SHIRQ) from all the arch-specific headers to
linux/signal.h.  This looks like a left-over after the irq-handling code
was consolidated.  The code was moved to kernel/irq/*, but the flags are
still left per-arch.

Right now, adding a new IRQ flag to the arch-specific header, like this
patch does:
http://cvs.sourceforge.net/viewcvs.py/*checkout*/alsa/alsa-driver/utils/patches/pcsp-kernel-2.6.10-03.diff?rev=1.1
no longer works, it breaks the compilation for all other arches, unless you
add that flag to all the other arch-specific headers too.  So I think such
a clean-up makes sense.
Signed-off-by: NStas Sergeev <stsp@aknet.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Arrange for all kernel printks to be no-ops.  Only available if
CONFIG_EMBEDDED.

This patch saves about 375k on my laptop config and nearly 100k on minimal
configs.
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove PAGE_BUG - repalce it with BUG and BUG_ON.
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch eliminates all kernel BUGs, trims about 35k off the typical
kernel, and makes the system slightly faster.
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a pair of rlimits for allowing non-root tasks to raise nice and rt
priorities. Defaults to traditional behavior. Originally written by
Chris Wright.

The patch implements a simple rlimit ceiling for the RT (and nice) priorities
a task can set.  The rlimit defaults to 0, meaning no change in behavior by
default.  A value of 50 means RT priority levels 1-50 are allowed.  A value of
100 means all 99 privilege levels from 1 to 99 are allowed.  CAP_SYS_NICE is
blanket permission.

(akpm: see http://www.uwsg.iu.edu/hypermail/linux/kernel/0503.1/1921.html for
tips on integrating this with PAM).
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Synchronize documentation with current interface.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The ioctl32_conversion routines will be deprecated: Remove them from the
crypto driver.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The ioctl32_conversion routines will be deprecated: Remove them from dasd_cmb
and handle the three cmb ioctls like all other dasd ioctls.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The first blocks on a cdl formatted dasd device are smaller than the blocksize
of the device.  Read requests are padded with a 'e5' pattern.  Write requests
should not pad the (user) buffer with 'e5' because a write request is not
allowed to modify the buffer.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The DASD device driver never reorders the I/O requests and relies on the
hardware to write all data to nonvolatile storage before signaling a
successful write.  Hence, the only thing we have to do to support write
barriers is to set the queue ordered flag.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The independent read-only flags in devmap, dasd_device and gendisk are not
kept in sync.  Use one bit per feature in the dasd driver and keep that bit in
sync with the gendisk bit.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The current limitation of 16 characters of the debug feature names turned out
to be insufficient.  Increase it to 64 characters.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

An arbitrary guest must not be allowed to trigger cmm actions.  Only one
specific guest namely the one that serves as the resource monitor may send cmm
messages.  Add a parameter that allows to specify the guest that may send
messages.  z/VMs resource manager has the name 'VMRMSVM' which is the default.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Provide an easy way to define a non-zero storage key at compile time.  This is
useful for debugging purposes.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The memory setup didn't take care of memory holes and this makes the memory
management think there would be more memory available than there is in
reality.  That causes the OOM killer to kill processes even if there is enough
memory left that can be written to the swap space.

The patch fixes this by using free_area_init_node with an array of memory
holes instead of free_area_init.  Further the patch cleans up the code in
setup.c by splitting setup_arch into smaller pieces.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix overflow in calculation of the new tod value in stop_hz_timer and fix
wrong virtual timer list idle time in case the virtual timer is already
expired in stop_cpu_timer.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Regenerate the default configuration for s390.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use the set_disk_ro() API when the backing file is read-only, to mark the disk
read-only, during the ->open().  The current hack does not work when doing a
mount -o remount.

Also, mark explicitly the code paths which should no more be triggerable (I've
removed the WARN_ON(1) things).  They should actually become BUG()s probably
but I'll avoid that since I'm not so sure the change works so well.  I gave it
only some limited testing.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Jens Axboe <axboe@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add some commentary about UML internals, for a strange trick.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use this:
	.set_page_dirty = __set_page_dirty_nobuffers,

We already dropped the inclusion of <linux/buffer_head.h>, and we don't have a
backing block device for this FS.

"Without having looked at it, I'm sure that hostfs does not use buffer_heads.
So setting your ->set_page_dirty a_op to point at __set_page_dirty_nobuffers()
is a reasonable thing to do - it'll provide a slight speedup."

This speedup is one less spinlock held and one less conditional branch, which
isn't bad.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix some console locking problems (including scheduling in atomic) and various
reorderings and cleanup in that code.  Not yet ready for 2.6.12 probably.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Reuse asm-x86-64/unistd.h to build our syscall table, like x86-64 already
does.

Like for i386, we must add some #defines for all the (right!) changes UML does
to x86-64 syscall table.

Note: I noted a bogus:
	[ __NR_sched_yield ] = (syscall_handler_t *) yield,

while doing this patch (which could only be a workaround for some strange bug,
but I would ignore this possibility).  I'm changing this without notice.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix the moved syscall table for the x86_64 SUBARCH:

- redirect __NR_chown and such to versions aware of 32-bit UIDs,

- avoid the useless hack for sys_nfsservctl,

- use sys_sendfile64 in the table rather than sys_sendfile.

- __NR_uselib is sys_ni_syscall on x86_64 (which does not support A.OUT).

- __NR_getrlimit is sys_getrlimit, not sys_old_getrlimit
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Split the i386 entry.S files into entry.S and syscall_table.S which is
included in the previous one (so actually there is no difference between them)
and use the syscall_table.S in the UML build, instead of tracking by hand the
syscall table changes (which is inherently error-prone).

We must only insert the right #defines to inject the changes we need from the
i386 syscall table (for instance some different function names); also, we
don't implement some i386 syscalls, as ioperm(), nor some TLS-related ones
(yet to provide).
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

GCC 2.95 uses __va_copy instead of va_copy.  Handle it inside compiler.h
instead of in a casual file, and avoid the risk that this breaks with a newer
compiler (which it could do).
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>