FW initialization routine can also be called while changing
virtual interface types.
This patch adds bool parameter "init" to init command routine
so as to differentiate between initialization during driver load
and change virtual interface handler.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This would be used to set mac address while changing virtual
interface to different types.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wdev is used even after del_virtual_interface handler in cfg80211
in nl80211_post_doit. Since we have freed wdev in handling of
del_virtual_intf, this can result into crash while deleting
interface.
Avoid this be not declaring wdev which part of
mwifiex_private structure but struct wireless_dev type.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

RTS threshold, fragmentation threshold are per device properties.
Setting them on any interface would be reflected for all other
interfaces as well. This patch removes unnesessary command download
per interface.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is not used anywhere execpt initialization.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This change fixes below sparse error:
drivers/ssb/main.c:94:16: warning: symbol 'ssb_sdio_func_to_bus'
was not declared. Should it be static?
Acked-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NPramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The nvram file can hold a key=value combination in which the value
may have spaces, ie. 'RAW1=80 02 fe ff'. The parsing functionality
did not deal with this so it gives an error message:

[621746.311635] brcmfmac: brcmf_nvram_handle_key
	warning: ln=90:col=11: '=' expected, skip invalid key entry

because RAW1=80 is being considerd as key=value pair and it expects
'=' sign after '02' for next key=value pair. This entry can be
completely ignored as firmware does not need it.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When revinfo retrieval fails we can not show the firmware version
in ethtool driver info. Store the result to be used when handling
ethtool driver info callback.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The ethtool driver info already contained the unique firmware
identifier. This patch adds the firmware release version.

   $ ethtool -i wlan4
   driver: brcmfmac
   version: 6.10.224.22
   firmware-version: 01-32bd010f
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Obtain device revision information and store it.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In some scenarios the chip number and revision may not be provided
by the bus layer. If the chip number is not filled, the common
layer will ask the firmware for this information.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Introducing a define that the caller of brcmu_boardrev_str() can
use to allocate enough room for buffer passed to the function.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In brcmf_usb_probe_cb() the device is checked to determine whether
it is already running firmware. However, when no firmware download
is needed it still continues to request the firmware files. This
is fixed by returning after successful setup.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

During suspend the bus state is put in the down state. When data
is being transmitted during this state then the netdev queue will
be close. This patch will wake the queue on state data if the
queue was closed.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Each bus driver is maintaing an exported bus state indicating
if upper layers can or cannot send data. SDIO is using this state
also for more private states. This makes handling the states and
state changes complex. This patch minimises the exposed states
and makes SDIO keep track of an internal state where necessary.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Before going in suspend state the watchdog thread needs to put the
device in bus sleep state, which assures it can go in deep-sleep
state during D3 state.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver always called cfg80211_disconnected() with reason parameter
set to zero, ie. unknown. However, firmware does provide a valid
802.11 reason code in DEAUTH and DISASSOC event message to the driver.
This patch passes the reason code to cfg80211_disconnected().
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Control frames are normally handled outside DPC, but sometimes
within DPC. To simplify code always handle control within DPC.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the system is resumed a deadlock can occur when DPC gets
entered before resume is complete. This patch fixes this by
properly checking the suspend state outside the claim_host code
block.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On every tx the flow worker is triggered. When running high
throughput data this causes an excessive amount of times the worker
gets activated. This patch starts scheduling the worker more relaxed
once outstanding tx has reached a certain depth.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This fixes issue reported by Dan Carpenter:
The patch 3277213f: "wil6210: ADDBA/DELBA flows" from Dec 23,
2014, leads to the following static checker warning:

        drivers/net/wireless/ath/wil6210/rx_reorder.c:205 wil_tid_ampdu_rx_alloc()
        error: scheduling with locks held: 'spin_lock:tid_rx_lock'

drivers/net/wireless/ath/wil6210/rx_reorder.c
   202  struct wil_tid_ampdu_rx *wil_tid_ampdu_rx_alloc(struct wil6210_priv *wil,
   203                                                  int size, u16 ssn)
   204  {
   205          struct wil_tid_ampdu_rx *r = kzalloc(sizeof(*r), GFP_KERNEL);
                                                                 ^^^^^^^^^^
   206
   207          if (!r)
   208                  return NULL;
   209
   210          r->reorder_buf =
   211                  kcalloc(size, sizeof(struct sk_buff *), GFP_KERNEL);
                                                                ^^^^^^^^^^^
   212          r->reorder_time =
   213                  kcalloc(size, sizeof(unsigned long), GFP_KERNEL);
                                                             ^^^^^^^^^^^
   214          if (!r->reorder_buf || !r->reorder_time) {
   215                  kfree(r->reorder_buf);
   216                  kfree(r->reorder_time);
   217                  kfree(r);
   218                  return NULL;
   219          }
   220

[ snip ]

   331          spin_lock_bh(&sta->tid_rx_lock);
                ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
spin lock held.

   332
   333          wil_tid_ampdu_rx_free(wil, sta->tid_rx[tid]);
   334          sta->tid_rx[tid] = wil_tid_ampdu_rx_alloc(wil, agg_wsize, ssn);
                                   ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
function called with the lock held.

   335
   336          spin_unlock_bh(&sta->tid_rx_lock);
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Access point require this API to check peer alive status.
Assume peer is alive when it is connected, because
firmware implements keep alive checks and will disconnect
peer if it is not alive.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement Tx status reporting using skb_complete_wifi_ack().
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Interrupt moderation parameters will never be passed as module
parameters. For product, they will be hard-coded after lab testing,
and for debugging, they can be altered via debugfs.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Due to HW limitation, inter-packet gap timeout max value is 13 usec.
Update of current thresholds from 15 to 13 usec.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Tuning rings size for performance optimization.
Increasing Tx ring size, allows buffering more packets for HW, thus
eliminating idle periods which were observed with smaller ring at
high throughput, because HW was fetching packets faster than driver was
filling them into the TX ring. Rx ring was similarly increased to
avoid same problems in Rx.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Tx queue was hard-coded to 1000 in ether_setup. Add wil_dev_setup
function which configures tx queue len to chosen default value
after calling ether_setup.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

upon cfg80211_stop_ap, a graceful AP shutdown is requested from firmware
followed by firmware reset.
In case graceful request failed, error was returned to cfg80211.

The change is to return success in this scenario, because firmware
reset will anyhow shutdown the AP.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.

The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Incorporate changes from firmware.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

After rtl8192cu download firmware routine, set fw_ready flag.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some devices do not support extended scan.
This patch adds support to enble ext_scan selectively.
For SD/PCIe interfaces, deefine ext_scan_support as part of
card structure and use it to initialize ext_scan in adapter
during registering device. For USB interfaces, we initialize
ext_scan during register_dev handler.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

USB8801 is Marvell's 1x1 802.11bgn offering.
Patch adds Device IDs support and defines TX buffer size.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SD8801 is Marvell's 1x1 802.11bgn offering.
This patch adds Device IDs for SD8801 and also defines card
structure which has definition for register offsets, buffer sizes etc.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Reviewed-by: NJames Cameron <quozl@laptop.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:

drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here

Fixes: 3a939a67 ("ath9k_htc: Add a module parameter to disable blink")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NHong Xu <hong@topbug.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Patch "rtlwifi: add support to send beacon frame" allows
the beaconing of rtl8192cu. But mesh beaconing is not
working. Fix this.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In AP mode, beacon frame is necessary to keep connection.
this patch adds a sending beacon frame routine in initialization routine.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds fix to set carrier state off during ndo_open.
Carrier should be set to ON when device is ready to send data.
In case of station/adhoc interface device is able to transfer
data after successful association/join operation.
For AP this would be after bss_active event.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Starting with kernel 3.19-rc1 early registration of bcma on MIPS is done
a bit later, with memory allocator available. This allows us to simplify
code by using standard bus scanning method.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The kernel's string library does in fact have strcasecmp, at least
since ded220bd ("[STRING]: Move strcasecmp/strncasecmp to
lib/string.c"). Moreover, this open-coded version is in fact wrong: If
the strings only differ in their last character, a and b have already
been incremented to point to the terminating NUL bytes, so they would
wrongly be treated as equal.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>