* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (142 commits)
  USB: fix race in autosuspend reschedule
  atmel_usba_udc: Keep track of the device status
  USB: Nikon D40X unusual_devs entry
  USB: serial core should respect driver requirements
  USB: documentation for USB power management
  USB: skip autosuspended devices during system resume
  USB: mutual exclusion for EHCI init and port resets
  USB: allow usbstorage to have LUNS greater than 2Tb
  USB: Adding support for SHARP WS011SH to ipaq.c
  USB: add atmel_usba_udc driver
  USB: ohci SSB bus glue
  USB: ehci build fixes on au1xxx, ppc-soc
  USB: add runtime frame_no quirk for big-endian OHCI
  USB: funsoft: Fix termios
  USB: visor: termios bits
  USB: unusual_devs entry for Nikon DSC D2Xs
  USB: re-remove <linux/usb_sl811.h>
  USB: move <linux/usb_gadget.h> to <linux/usb/gadget.h>
  USB: Export URB statistics for powertop
  USB: serial gadget: Disable endpoints on unload
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Don't take semaphore in cpufreq_quick_get()
  [CPUFREQ] Support different families in fid/did to frequency conversion
  [CPUFREQ] cpufreq_stats: misc cpuinit section annotations
  [CPUFREQ] implement !CONFIG_CPU_FREQ stub for  cpufreq_unregister_notifier()
  [CPUFREQ] mark hotplug notifier callback as __cpuinit
  [CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
  [CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
  [CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
  [CPUFREQ] Longhaul - Add support for PM133 northbridge
  [CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for

* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-x86: (40 commits)
  x86: HPET add another ICH7 PCI id
  x86: HPET force enable ICH5 suspend/resume fix
  x86: HPET force enable for ICH5
  x86: HPET try to activate force detected hpet
  x86: HPET force enable o ICH7 and later
  x86: HPET restructure hpet code for hpet force enable
  clock events: allow replacement of broadcast timer
  i386/x8664: cleanup the shared hpet code
  i386: Remove the useless #ifdef in i8253.h
  ACPI: remove the now unused ifdef code
  jiffies: remove unused macros
  x86_64: cleanup apic.c after clock events switch
  x86_64: remove now unused code
  x86: unify timex.h variants
  x86: kill 8253pit.h
  x86: disable apic timer for AMD C1E enabled CPUs
  x86: Fix irq0 / local apic timer accounting
  x86_64: convert to clock events
  x86_64: Add (not yet used) clock event functions
  x86_64: prepare idle loop for dynamic ticks
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (23 commits)
  ocfs2: Optionally return filldir errors
  ocfs2: Write support for directories with inline data
  ocfs2: Read support for directories with inline data
  ocfs2: Write support for inline data
  ocfs2: Read support for inline data
  ocfs2: Structure updates for inline data
  ocfs2: Cleanup dirent size check
  ocfs2: Rename cleanups
  ocfs2: Provide convenience function for ino lookup
  ocfs2: Implement ocfs2_empty_dir() as a caller of ocfs2_dir_foreach()
  ocfs2: Remove open coded readdir()
  ocfs2: Pass raw u64 to filldir
  ocfs2: Abstract out core dir listing functionality
  ocfs2: Move directory manipulation code into dir.c
  ocfs2: Small refactor of truncate zeroing code
  ocfs2: move nonsparse hole-filling into ocfs2_write_begin()
  ocfs2: Sync ocfs2_fs.h with ocfs2-tools
  [PATCH] fs/ocfs2/: removed unneeded initial value and function's return value
  ocfs2: Implement show_options()
  ocfs2: Clear slot map when umounting a local volume
  ...

* 'isdn-cleanups' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  [ISDN] HiSax diva: split setup into three smaller functions
  [ISDN] HiSax sedlbauer: move ISAPNP and PCI code into functions of their own
  [ISDN] HiSax elsa: split huge setup function into four smaller functions
  [ISDN] HiSax avm_pci: split setup into three smaller functions
  [ISDN] Remove CONFIG_PCI ifdefs from 100% PCI source code

* 'hysdn' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  [ISDN] hysdn: convert to PCI hotplug API

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc: use correct unregister function for led trigger

This patch (as1002) fixes a small race which can occur when a driver
expects usbcore to reschedule an autosuspend request.  If the request
arrives too late, it won't be rescheduled.  The patch adds an extra
argument to autosuspend_check(), indicating that a reschedule is
needed no matter how much time has elapsed.

It also tries to avoid letting asynchronous changes to the value of
jiffies cause a delay to become negative, by caching a local copy of
the current time.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Keep track of the device status (as returned by the GET_STATUS
request) and allow it to be manipulated by set_selfpowered() as
well as SET_FEATURE/CLEAR_FEATURE (for remote wakeup)

Implement the wakeup() op, which refuses to do anything if the
DEVICE_REMOTE_WAKEUP feature wasn't set by the host.  Now this
driver passes USBCV (at least, with gadget zero).

Fix one more locking bug; lockdep is every developer's friend.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Not surprisingly the Nikon D40X DSC needs the same quirks as the D40,
but it has a separate ID.
See http://bugs.gentoo.org/show_bug.cgi?id=191431

From: Ortwin Glück <odi@odi.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as997) fixes a bug in the USB serial core.  The core needs
to pay attention to drivers' requirements regarding the number and
type of endpoints a device has.

At the same time, the patch changes the NUM_DONT_CARE constant (which
is stored in a single-byte field) from -1 to a safer, unsigned value.
It also improves the kerneldoc for several fields in the
usb_serial_driver structure.

Finally, the patch replaces a list_for_each() with list_for_each_entry().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as998) adds documentation on how USB power management
works and how to use it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

System suspends and hibernation are supposed to be as transparent as
possible.  By this reasoning, if a USB device is already autosuspended
before the system sleep begins then it should remain autosuspended
after the system wakes up.

This patch (as1001) adds a skip_sys_resume flag to the usb_device
structure and uses it to avoid waking up devices which were suspended
when a system sleep began.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order.  If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused.  The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Attached is a very small patch (several comment lines) and a one-line
coded change) that allows for USB storage devices that are larger than
2TB.

At the company where I work we need such support, and one of my
co-workers, Jane Liu, pointed out that SCSI low-layer drivers need to
specify what size CDBs they accept. After looking through the code it
became obvious that the current USB Storage code accepted the default of
12-byte CDBs, so I changed it to accept 16-byte CDBs. This allows our
device to work.
Signed-off-by: NRichard Sharpe <rsharpe@richardsharpe.com>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch supports for SHARP WS011SH[0] to ipaq.c

[0]: http://www.willcom-inc.com/ja/lineup/ws/011sh/index.html
(Sorry , Japanese only.)
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a driver for the Atmel USBA UDC which can be found integrated
on AT32AP700x AVR32 processors. For hardware documentation, please see
the AT32AP7000 data sheet:

http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf

This is a dual speed controller (connects at high or full speed).
The driver supports up to 7 control, bulk, interrupt and isochronous
endpoints with some constraints. Bulk, interrupt and isochronous
transfers are driven by DMA.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds SSB bus glue for the USB OHCI HCD. 
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cleanup: references to two PM routines (and HCD entry points)
that no longer exist are swapped with their replacements.

Evidently au1xxx and ppc-soc EHCI support doesn't get compiled
with power management very much, or these build bugs would have
been patched long ago.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add OHCI big endian frame_no quirk.  The frame_no value stored in the
HCCA is a 16 bit field at a specific offset, but since not all CPUs can
do 16-bit memory accesses it's used as a 32 bit field.  And that's why
big-endian OHCI must shift 16 bits ... unless the spec is not followed.

Currently there's one MPC52xx platform that doesn't need the shift. This
patch adds a new "big endian frame_no" quirk to control that at runtime.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Funsoft has a bogus ioctl handler doing bogus termios handling in a bogus
manner. Fortunately we can simply delete all the bogus bits and get the
right default behaviour !
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Visor has a huge complex routine which displays termios bits for debug
but doesn't do anything. Get the correct behaviour by removing it all
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as996) adds an unusual_devs entry for the Nikon DSC D2Xs
camera.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove <linux/usb_sl811.h> ... somehow this was recreated when
the Blackfin arch was merged, instead of using <linux/usb/sl811.h>
which is the correct header.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move <linux/usb_gadget.h> to <linux/usb/gadget.h>, reducing
some of the clutter in the main include directory.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

powertop currently tracks interrupts generated by uhci, ehci, and ohci,
but it has no way of telling which USB device to blame USB bus activity on.
This patch exports the number of URBs that are submitted for a given device.
Cat the file 'urbnum' in /sys/bus/usb/devices/.../
Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After Serial gadget is being unloaded, neither serial itself, nor other
gadget stuff can be loaded subsequently.
Signed-off-by: NVitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Kill two unused variables in drivers/usb/misc/sisusbvga/sisusb.c.
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a longstanding race in the Ethernet gadget driver, which can cause an
oops on device disconnect.  The fix is just to make the TX path check
whether its freelist is empty.  That check is otherwise not necessary,
since the queue is always stopped when that list empties (and restarted
when request completion puts an entry back on that freelist).

The race window starts when the network code decides to transmit a packet,
and ends when hard_start_xmit() grabs the freelist lock.  When disconnect()
is called inside that window, it shuts down the TX queue and breaks the
otherwise-solid assumption that packets are never sent through a TX queue
that's stopped.
Signed-off-by: NBenedikt Spranger <bene@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/misc/sisusbvga/sisusb.c: In function 'sisusb_open':
drivers/usb/misc/sisusbvga/sisusb.c:2444: warning: 'sisusb' is used uninitialized in this function

I can tell that'll oops just by looking at it.

How come this code assume a 7,000 column xterm? :(

Cc: Felipe Balbi <felipe.lima@indt.org.br>
Cc: Thomas <thomas@winischhofer.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that accessed register of this controller after
having called iounmap().
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that does not work in the big endian machine.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that does not work in the case of bRequest = 0x05 in
Class or Vendor Request.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes four needlessly global functions static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch implements a USB serial port driver for the Winchiphead
CH341 USB-RS232 Converter. This chip also implements an IEEE 1284
parallel port, I2C and SPI, but that is not supported by the driver.
Signed-off-by: NFrank A Kingswood <frank@kingswood-consulting.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When an error occurs, existing logging uses dbg() so the cause of a
problem is hard to determine. Error conditions shouldn't only be
properly reported with debugging enabled.

A side effect of this change is that when an uninitialised device is
started, a log message similar to the following is sent:
	cxacru 5-2:1.0: receive of cm 0x90 failed (-104)
This is normal - the device did not respond so firmware will be loaded.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Acked-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds an additional device ID to the cp2101 USB serial
driver. This device is a Gemalto Prox-PU or CU contactless card reader
(ISO14443-A/B and Mifare). The reader is a standard Gemalto serial
proximity reader using the Gemalto Block Protocol (see reader's
documentation) bundled with a built-in CP2102 for serial/USB
conversion.

Signed-off-by: Edouard Lafargue (edouard@lafargue.name)
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Upgrade the unusual_devs.h file to support the Nikon D200
Signed-off-by: NMike Pagano <mpagano-kernel@mpagano.com>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as995) cleans up the remains of the former NO_AUTOSUSPEND
quirk.  Since autosuspend is disabled by default, we will let
userspace worry about which devices can safely be suspended.  Thus the
lengthy series of quirk entries is no longer needed, and neither is
the quirk ID.  I suppose someone might eventually run across a hub
that can't be suspended; let's ignore the possibility for now.

The patch also cleans up the hasty way in which autosuspend gets
disabled.  Setting udev->autosuspend_delay to -1 wasn't quite right,
because the value is always supposed to be a multiple of HZ.  It's
better to leave the delay value alone and set autosuspend_disabled,
which is what the quirk routine used to do.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as992) fixes a recently-added bug.  During a FREEZE or
PRETHAW suspend notification, non-root devices don't actually get
suspended.  So we shouldn't tell their parent hubs that they did.

(This code path used to be skipped over, until the FREEZE/PRETHAW test
got moved out of usb_suspend_both() into generic_suspend().)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>