Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.

Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.

Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().

Cc: stable@vger.kernel.org
Signed-off-by: NGeorge Cherian <george.cherian@cavium.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.

Verified on Sunrise Point-LP and Cannon Lake.

Cc: stable@vger.kernel.org
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.

Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.

Restrict the USB2 resume status check in USB2 roothub to fix hang issue.

Cc: stable@vger.kernel.org
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Observed "TRB completion code (27)" error which corresponds to Stopped -
Length Invalid error(xhci spec section 4.17.4) while connecting USB to
SATA bridge.

Looks like this case was not considered when the following patch[1] was
committed. Hence adding this new check which can prevent
the invalid byte size error.

[1] ade2e3a1 xhci: handle transfer events without TRB pointer

Cc: <stable@vger.kernel.org>
Signed-off-by: NSandeep Singh <sandeep.singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing  NULL pointer dereference.

Check if xhci->shared_hcd is still valid before handing USB3 port events

Cc: <stable@vger.kernel.org>
Reported-by: NPeter Chen <peter.chen@nxp.com>
Tested-by: NJack Pham <jackp@codeaurora.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()

The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)

Afer commit fe190ed0 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.

shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.

xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087 ("usb: xhci: plat: Create both
HCDs before adding them")

Fixes: fe190ed0 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: NJack Pham <jackp@codeaurora.org>
Tested-by: NJack Pham <jackp@codeaurora.org>
Tested-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The generic power-domain framework has been updated to allow devices
that require more than one power-domain to create a new device for
each power-domain required and then link these new power-domain
devices to the consumer device.

Update the Tegra xHCI driver to use the new APIs provided by the
generic power-domain framework so we can use the generic power-domain
framework for managing the xHCI controllers power-domains. Please
note that to maintain backward compatibility with older device-tree
blobs these new generic power-domain APIs are only used if the
'power-domains' property is present and otherwise we fall back to
using the legacy Tegra APIs for managing the power-domains.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the XUSB power domains used by the Tegra xHCI controller are
never powered off on the removal of the driver, however, they will be
powered off on probe failure. Update the removal code to be consistent
with the probe failure path to power off the XUSB power domains.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

atmel,oc-gpio is optional. Request its irq only when atmel,oc is set
in device tree.

devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its
return value for NULL before error, because it is more probable that
atmel,oc is not set.

This fixes the following errors on boards where atmel,oc is not set in
device tree:
[    0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[    0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[    0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Apollo Lake has the same internal USB role mux as
Intel Cherry Trail.

Cc: <stable@vger.kernel.org>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Give USB3 devices a better chance to enumerate at USB3 speeds if
they are connected to a suspended host.
Porting from "671ffdff xhci: resume USB 3 roothub first"

Cc: <stable@vger.kernel.org>
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The workaround for missing CAS bit is also needed for xHC on Intel
sunrisepoint PCH. For more details see:

Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.

This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.

This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to  autoresume/autosuspend
root hub properly.
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The XUSB firmware header is in little endian byte order, so make the
fields __le32 and __le16 instead of u32 and u16 to avoid warnings from
sparse when the fields are used with the endian-aware __le32_to_cpu()
and __le16_to_cpu() accessors, respectively.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The xhci controller on Alpine and Titan Ridge keeps the whole thunderbolt
awake if the host controller is not allowed tp sleep.
This is the case even if no USB devices are connected to the host.

Because of this bigger impact, allow runtime pm as default for these xhci
controllers in the driver.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use soft retry to recover from a USB Transaction Errors that are caused by
temporary error conditions. The USB device is not aware that the xHC
has halted the endpoint, and will be waiting for another retry

A Soft Retry perform additional retries and recover from an error which has
caused the xHC to halt an endpoint.

Soft retry has some limitations:
Soft Retry attempts shall not be performed on Isoch endpoints
Soft Retry attempts shall not be performed if the device is behind a TT in
a HS Hub

Software shall limit the number of unsuccessful Soft Retry attempts to
prevent an infinite loop.

For more details on Soft retry see xhci specs  4.6.8.1
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The TPL support is used to identify targeted devices during
EH2.0 and EH3.0 certification test, the user can add "tpl-support"
at dts to enable this feature.
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Supports SSP scheduling only for SSP device directly connected
to root hub but not through external USB3 gen2 hub which need
use a new scheduling way.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Supports LowSpeed and FullSpeed INT/ISOC bandwidth scheduling
with USB multi-TT
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Mainly improve SuperSpeed ISOC bandwidth in last microframe,
and LowSpeed/FullSpeed IN INT/ISOC bandwidth in split and
idle microframes by introduing a bandwidth budget table;
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the interval equal zero, needn't round up to power of two
for the number of packets in each ESIT, so fix it.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make use of maximum ESIT payload of endpoint context to calculate
the number of packets to send in each ESIT
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It's dangerous to use empty code define.
Furthermore it lead to the following warning:
"suggest braces around empty body in an « else » statement"

So let's replace emptyness by "do {} while(0)"

Furthermore, as suggested by Joe Perches, rename the macro to INCR.
Signed-off-by: NCorentin Labbe <clabbe@baylibre.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is code in the .remove() hook to handle the drvdata
being NULL, for good reasons: it is never set, so it will
always be NULL. As I moved code around, static checkers
start complaining.

Instead of this, make sure to always set it on successful
probe so we can always dereference it on the remove path.

Use the platform_device_[set|get]_drvdata() since this is
a platform device.

Fixes: ffa8a31b ("usb: host: fotg2: add silicon clock handling")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Device tree support.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use a proper PHY driver, instead of hooks to a board support package.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It's unused.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is done do that it could be enabled alongside other platform EHCI
glue drivers on multiplatform kernels.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The MTK xHCI controller use some reserved bytes in endpoint context for
bandwidth scheduling, so need keep them in xhci_endpoint_copy();

The issue is introduced by:
commit f5249461 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
It resets endpoints and will drop bandwidth scheduling parameters used
by interrupt or isochronous endpoints on MTK xHCI controller.
Fixes: f5249461 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")

Cc: stable@vger.kernel.org
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Paul pointed out that the 50-ms sleep during OHCI initialization takes
up a large fraction of a system's boot time.  Things get worse when
there are two OHCI controllers present, each requiring 50 ms.

However, there really is no need to send a 50-ms reset signal out all
the root-hub ports during initialization.  The ports themselves will
be disabled, and the only way to enable a port is to reset it.
Therefore all attached USB devices will receive a proper reset in any
case.  The controller reset does not need to be long enough to reset
those other devices, so the 50-ms delay isn't necessary.

Without the delay, there is no remaining incentive for skipping the
reset when the controller is already in the RESET state.  This patch
removes the test, issuing the command unconditionally, and removes the
following delay.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Suggested-by: NPaul Menzel <pmenzel@molgen.mpg.de>
Tested-by: NPaul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When used in a system with software-controlled silicon clocks,
the FOTG210 needs to grab, prepare and enable the clock.

This is needed on for example the Cortina Gemini, where the
platform will by default gate off the clock unless the
peripheral (in this case the USB driver) grabs and enables
the clock.

If there is no clock available on the platform, we live
without it. Make sure to percolate probe deferrals.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.

[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
	msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
	[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
	usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
	usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
	i_usX2Y_urb_complete in i_usX2Y_subs_startup

Note that [FUNC_PTR] means a function pointer call is used.

To fix this bug, msleep() is replaced with mdelay().

This bug is found by my static analysis tool DSAC.
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In xhci_plat_probe() both sysdev and pdev->dev are being used
for finding quirks. There are some drivers(like dwc3 host.c)
which adds quirks(like usb3-lpm-capable) into pdev and the logic
present in xhci_plat_probe() checks for quirks in either sysdev
or pdev for finding the quirks. Because of this logic, some of
the quirks are getting missed(usb3-lpm-capable quirk added by dwc3
host.c driver is getting missed).This patch fixes this by iterating
over all the available parents for finding the quirks. In this way
all the quirks which are present in child or parent are correctly
updated.
Signed-off-by: NAnurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure the cancelled URB is on the current endpoint ring.

If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.

Don't try to stop the ring. It would be useless.

This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.

Cc: <stable@vger.kernel.org>
Tested-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If td_list is not empty the cfg_cmd will not be freed,
call xhci_free_command to free it.
Signed-off-by: NZheng Xiaowei <zhengxiaowei@ruijie.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Set the coherent_dma_mask for the PS3 ehci, ohci, and snd devices.

Silences WARN_ON_ONCE messages emitted by the dma_alloc_attrs() routine.
Reported-by: NFredrik Noring <noring@nocrew.org>
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Pointer dev is being assigned but is never used hence it is
redundant and can be removed.

Cleans up clang warning:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Variable num_ports is being assigned but is never used hence it is
redundant and can be removed.

Cleans up clang warning:
warning: variable 'num_ports' set but not used [-Wunused-but-set-variable]
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Variable t is being assigned but is never used hence it is
redundant and can be removed.

Cleans up clang warning:
warning: variable 't' set but not used [-Wunused-but-set-variable]
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>