Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If a device plug/unplug is detected on an ATI SB700 USB controller in D3,
it appears to set the port status register but not the controller status
register. As a result we'll fail to detect the plug event. Check the port
status register on resume as well in order to catch this case.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable <stable@kernel.org> [after .39-rc1 is out]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the gadget code, there are several DBG() macro invocations that explicitly
print the calling function's name while DBG() macro itself does this anyway;
most of these were added by commit f11d893d
(usb: musb: support ISO high bandwidth for gadget mode). Remove the duplicated
printing, somewhat clarifying the messages at the same time...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

most of our notifications, will be called from IRQ
context, so an atomic notifier suits the job better.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

OMAP4430 is embedded with UTMI PHY. This PHY does not support the
OTG features like ID pin detection and VBUS detection. This function
is exported to an external companion chip TWL6030. Software must retrieve
the OTG HNP and SRP status from the TWL6030 and configure the bits inside
the control module that drive the related USBOTGHS UTMI interface signals.
It must also read back the UTMI signals needed to configure the TWL6030
OTG module.

Can find more details in the TRM[1].
[1]:http://focus.ti.com/pdfs/wtbu/OMAP4430_ES2.0_Public_TRM_vJ.pdf

In OMAP4430 musb driver VBUS and ID notifications are received from the
transceiver driver. If the cable/device is connected during boot,
notifications from transceiver driver will be missed till musb driver
is loaded.
Patch to configure the transceiver in the platform_enable/disable
functions and enable the vbus in the gadget driver based on the
last_event of the otg_transceiver.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Save the last event in the otg_transceiver so that it can used in the
musb driver and gadget driver to configure the musb and enable the
vbus for host mode and OTG mode, if the device is connected during boot.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Introduce the twl6030_phy_suspend function and assign to otg.set_suspend
function pointer.
This function is used by the musb-omap2430 platform driver
during suspend/resume.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To get the ID status there was an I2C read transfer. Removed this I2C
read transfer as this info can be used from existing variable(linkstat).
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove the regulator enable while driver loading and enable it only when
the cable/device is connected and disable it when disconnected.

Remove the configuration of config_state and config_trans register
configuration as these registers are programmed when regulator
enable/disable is called.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Calling runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings.

Enable clock, configure no-idle/standby when active and configure force idle/standby
and disable clock when idled. This is taken care by the runtime framework when
driver calls the pm_runtime_get_sync and pm_runtime_put_sync APIs.
Need to configure MUSB into force standby and force idle mode when usb not used
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

struct usb_request's list_head is supposed to be
used only by gadget drivers, but musb is abusing
that. Give struct musb_request its own list_head
and prevent musb from poking into other driver's
business.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Just a few cosmetic fixes to usb_gadget_probe_driver()
and usb_gadget_unregister_driver().

Decreased a few indentation levels with goto statements.

While at that, also add the missing call to musb_stop().
If we don't have OTG, there's no point of leaving
MUSB prepared for operation if a gadget driver fails
to probe. The same is valid for usb_gadget_unregister_driver(),
since we are removing the gadget driver and we don't have
OTG, we can completely unconfigure MUSB.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During development, even though board is wired
to e.g. OTG, we might want to compile host-only
or peripheral-only configurations.

Let's allow that to happen.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use bitmap_set()/bitmap_clear() to fill/zero a region of a bitmap
instead of doing set_bit()/clear_bit() each bit.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that ehci_run don't call ehci_reset, we can use ehci_run.
Signed-off-by: NMatthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

TDI driver does the ehci_reset in their reset callback.
Don't reset in ehci_run because configuration settings done in
platform driver will be reset.

This will allow to make msm use ehci_run.
Signed-off-by: NMatthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver private data is retrieved incorrectly which results
a crash when written into "mode" debugfs file.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below compiler warning

drivers/usb/otg/msm72k_otg.c:257: warning: 'msm_otg_suspend' defined but not used
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add const modifier before global variable realtek_cr_ids.
Signed-off-by: Nwwang <wei_wang@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix some sparse warning for realtek_cr patch
Signed-off-by: Nwwang <wei_wang@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

resumption of devices can fail. Errors must be handled.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The device never needs to be resumed in close(). But the counters
must be balanced. As resumption can fail, but the counters must
be balanced, use the _no_resume() version which cannot fail.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If an error happens during resumption.
The remaining data has to be cleanly discarded and the pm
counters have to be adjusted.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As soon as the first error happens, the write must
be stopped, lest we send mutilated messages.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

An error in the write code path would permanently disable
runtime PM in this driver
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes two errors:
- the device is busy if a message was recieved even if resubmission fails
- the device is not busy if resubmission fails due to -EPERM
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In function at91udc_probe()
call put_device() when device_register() fails.
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The document says:
|2.1 Problem description
|    When at least two USB devices are simultaneously running, it is observed that
|    sometimes the INT corresponding to one of the USB devices stops occurring. This may
|    be observed sometimes with USB-to-serial or USB-to-network devices.
|    The problem is not noticed when only USB mass storage devices are running.
|2.2 Implication
|    This issue is because of the clearing of the respective Done Map bit on reading the ATL
|    PTD Done Map register when an INT is generated by another PTD completion, but is not
|    found set on that read access. In this situation, the respective Done Map bit will remain
|    reset and no further INT will be asserted so the data transfer corresponding to that USB
|    device will stop.
|2.3 Workaround
|    An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can
|    be implemented and if a certain Done bit is never set, verification of the PTD completion
|    can be done by reading PTD contents (valid bit).
|    This is a proven workaround implemented in software.

Russell King run into this with an USB-to-serial converter. This patch
implements his suggestion to enable the high frequent SOF interrupt only
at the time we have ATL packages queued. It goes even one step further
and enables the SOF interrupt only if we have more than one ATL packet
queued at the same time.

Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x]
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ehci_lpm_set_da and ehci_lpm_check are EHCI 1.1 specific functions which
are not used on many platforms but do generate annoying gcc warnings
Signed-off-by: NMaksim Rayskiy <mrayskiy@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need FUSB300_MAX_NUM_EP (16) names otherwise the last 8 names get
initialized to garbage values in fusb300_probe().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a patch that seems to make the USB hangs on the S3C244X go away.
At least a good amount of ping torture didn't make them come back so far.

The issue is that, if there are several back-to-back packets, sometimes no
interrupt is generated for one of them. This seems to be caused by the
mysterious dual packet mode, which the USB hardware enters automatically
if the endpoint size is half that of the FIFO. (On the 244X, this is the
normal situation for bulk data endpoints.)

There is also a timing factor in this. It seems that what happens is that
the USB hardware automatically sends an acknowledgement if there is only one
packet in the FIFO (the FIFO has space for two). If another packet arrives
before the host has retrieved and acknowledged the previous one, no interrupt
is generated for that second one.

However, there may be an indication. There is one undocumented bit (none
of the 244x manuals document it), OUT_CRS1_REG[1], that seems to be set
suspiciously often when this condition occurs. There is also
CLR_DATA_TOGGLE, OUT_CRS1_REG[7], which may have a function related to
this. (The Samsung manual is rather terse on that, as usual.)

This needs to be examined further. For now, the patch seems to do the
trick.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This PCH_UDC driver does not work normally when "Ethernet gadget" is used.

This patch fixed this issue.
The following was modified.
 - The FIFO flush process.
 - The descriptor creation process.
 - The adjustment of DMA buffer align.

Currently the PCH_UDC driver can work normally with "Ethernet gadget",
"Serial gadget" or "File-backed Storage Gadget".
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reorder the driver->name assignment so the 'iProduct' could be initialized
as well if both 'name' and 'iProduct' come as NULL by default.

Also, remove the misplaced 'extern' keyword.
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While checking valid interface number we should compare MAX_CONFIG_INTERFACES
with the variable 'intf' (which holds the lower 8bits of w_index) rather than
'w_index'
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit b7d5b439.
It conflicts with commit baab93af "USB:
EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't
work properly.

Cc: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea.  The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space.  The normal capable() interface returns
true on success, but the LSM interface returns 0 on success.  This thinko
is now fixed in this patch, and has been confirmed to work properly.

So, once again...Eric Paris noted that commit de139a33 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: NEric Paris <eparis@redhat.com>
Tested-by: NDave Young <hidave.darkstar@gmail.com>
Acked-by: NJames Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJames Morris <jmorris@namei.org>

The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.

( Please note that Type 2 is not listed in Table 3 in Sec 6.2
  ("Required Structures and Data") of the SMBIOS v2.7
  Specification. )

Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.

Before the fix:
  (i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
 (ii) oops output:  Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6

After the fix:
  (i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
 (ii) oops output:  Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: NNaga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.

v2: testing options

v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852
https://bugzilla.kernel.org/show_bug.cgi?id=24462
https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prevent divider overflow.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28932Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>