- 21 7月, 2016 8 次提交
-
-
由 Jacob Keller 提交于
When stop_hw() routine fails with FM10K_ERR_REQUESTS_PENDING, this indicates that the Tx or Rx queues did not shutdown within the time limit. Print a more suitable message at the dev_info level instead of dev_err. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
A while ago, an additional check for the switch being ready was added to reset_hw. A recent refactor accidentally made this check return an error code on failure which caused fm10k_probe to fail when the switch wasn't brought up first. The original reasoning for the check was to prevent additional data path reset when the fabric wasn't ready yet. However, there isn't a compelling reason to keep the check, as the data path reset will restore hardware to a known good state. Remove the check and perform the data path reset regardless of the switch manager state. An alternative fix is to return FM10K_SUCCESS instead, and bypass the actual data path reset. This should be fine as we will perform a reset_hw once the switch is active. However, since data path reset will reset many parts of the hardware it seems better to just perform the reset regardless of switch state. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Don't report FM10K_ERR_REQUESTS_PENDING when we fail to disable queues within the timeout. This can occur due to a hardware Tx hang, or when the switch ethernet fabric is resetting while we are transmitting traffic. It can sometimes take up to 500ms before the Tx DMA engine gives up. Instead, just skip the DMA engine check and perform a data-path reset anyways. Add a statistic counter to keep track of the number of resets occurring while we have pending DMA on the rings. In order to prevent having to re-assign err to 0, re-order the last few items of the reset_hw_pf function so that we don't perform "return err" at the end. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Ngai-Mint Kwan 提交于
When a data path reset is initiated, write control to the PCIE_GMBX is yanked from the switch manager. The switch manager writes to this register to clear mailbox global interrupt bits as part of its mailbox interrupt handling routine. When the device recovers from the data path reset and these bits are not cleared, it will prevent future mailbox global interrupts from being triggered. Upon confirming that the device has exited from a data path reset, clear these bits to ensure the proper functioning of the mailbox global interrupt. Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Also prevent updating stats while the interface is down. If we're already updating stats, just return doing nothing. When we take the device down, block stat updates until we come back up. This ensures that we avoid tearing down rings when we're updating statistics, and prevents updating statistics until we're up. We can't re-use the __FM10K_DOWN for this because it wouldn't prevent multiple threads from accessing statistics. Neither does it prevent the case where we start updating stats and then start going down in another thread. The fm10k_get_stats64 is except from this, because it has a completely different flow which does not suffer from the same issues as fm10k_update_stats might. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
It's currently possible for fm10k_update_stats to be called during the window when we go down and the rings are removed. This can result in a null pointer dereference. In fm10k_get_stats64 we work around this by using ACCESS_ONCE and a null pointer check inside the loop. Use this same flow in the fm10k_update_stats to avoid the potential null pointer. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Return early from fm10k_down() when we are already down, since that means another thread is either already finished or has started going down, so shouldn't conflict with them. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 12 7月, 2016 1 次提交
-
-
由 Sabrina Dubroca 提交于
Some comments weren't updated to reflect the renaming of ndo's and the change of arguments. Signed-off-by: NSabrina Dubroca <sd@queasysnail.net> Acked-by: NAlexander Duyck <aduyck@mirantis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 6月, 2016 4 次提交
-
-
由 Bhaktipriya Shridhar 提交于
alloc_workqueue replaces deprecated create_workqueue(). A dedicated workqueue has been used since the workitem (viz fm10k_service_task, which manages and runs other subtasks) is involved in normal device operation and requires forward progress under memory pressure. create_workqueue has been replaced with alloc_workqueue with max_active as 0 since there is no need for throttling the number of active work items. Since network devices may be used in memory reclaim path, WQ_MEM_RECLAIM has been set to guarantee forward progress. flush_workqueue is unnecessary since destroy_workqueue() itself calls drain_workqueue() which flushes repeatedly till the workqueue becomes empty. Hence the call to flush_workqueue() has been dropped. Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
The index calculated when looping through the indir array passed to fm10k_write_reta was incorrectly calculated as the first part i needs to be multiplied by 4. Fixes: 0cfea7a65738 ("fm10k: fix possible null pointer deref after kcalloc", 2016-04-13) Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Alexander Duyck 提交于
While reviewing the i40e driver changes to support page based receive I realized that I had overlooked the fact that the fm10k hardware required a 512 byte alignment for Rx buffers. This patch is meant to address that by changing the alignment for Rx buffers to 512 bytes instead of allowing it to be L1 cache aligned. Signed-off-by: NAlexander Duyck <aduyck@mirantis.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
The FM10K_MAX_DATA_PER_TXD is really just using a bitshift as a power of 2 operation in an efficient manner. We shouldn't represent this as a BIT() because that obscures the intention of the operation. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 18 6月, 2016 1 次提交
-
-
由 Alexander Duyck 提交于
This change replaces the network device operations for adding or removing a VXLAN port with operations that are more generically defined to be used for any UDP offload port but provide a type. As such by just adding a line to verify that the offload type if VXLAN we can maintain the same functionality. Signed-off-by: NAlexander Duyck <aduyck@mirantis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 5月, 2016 1 次提交
-
-
由 Florian Westphal 提交于
Replace all trans_start updates with netif_trans_update helper. change was done via spatch: struct net_device *d; @@ - d->trans_start = jiffies + netif_trans_update(d) Compile tested only. Cc: user-mode-linux-devel@lists.sourceforge.net Cc: linux-xtensa@linux-xtensa.org Cc: linux1394-devel@lists.sourceforge.net Cc: linux-rdma@vger.kernel.org Cc: netdev@vger.kernel.org Cc: MPT-FusionLinux.pdl@broadcom.com Cc: linux-scsi@vger.kernel.org Cc: linux-can@vger.kernel.org Cc: linux-parisc@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-hams@vger.kernel.org Cc: linux-usb@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: linux-s390@vger.kernel.org Cc: devel@driverdev.osuosl.org Cc: b.a.t.m.a.n@lists.open-mesh.org Cc: linux-bluetooth@vger.kernel.org Signed-off-by: NFlorian Westphal <fw@strlen.de> Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com> Acked-by: NMugunthan V N <mugunthanvnm@ti.com> Acked-by: NAntonio Quartulli <a@unstable.cc> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 4月, 2016 1 次提交
-
-
由 Hannes Frederic Sowa 提交于
fm10k_open requires rtnl_lock to be held. Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Shannon Nelson <shannon.nelson@intel.com> Cc: Carolyn Wyborny <carolyn.wyborny@intel.com> Cc: Don Skidmore <donald.c.skidmore@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: John Ronciak <john.ronciak@intel.com> Cc: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 4月, 2016 17 次提交
-
-
由 Jacob Keller 提交于
Check for and handle IPv6 extended headers so that Tx checksum offload can be done. Also use skb_checksum_help for unexpected cases. This was originally discovered in ixgbe. Reported-by: NMark Rustad <mark.d.rustad@intel.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Update every header file and other locations to consistently use Intel(R) instead of just Intel. Also update copyright year of files which we modified. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
When writing a new default redirection table, we needed to populate a new RSS table using ethtool_rxfh_indir_default. We populated this table into a region of memory allocated using kcalloc, but never checked this for NULL. Fix this by moving the default table generation into fm10k_write_reta. If this function is passed a table, use it. Otherwise, generate the default table using ethtool_rxfh_indir_default, 4 at at time. Fixes: 0ea7fae4 ("fm10k: use ethtool_rxfh_indir_default for default redirection table") Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Ngai-Mint Kwan 提交于
Deleting lport when multicast mode is configured to FM10K_XCAST_MODE_ALLMULTI or FM10K_XCAST_MODE_PROMISC will result in generating orphaned multicast-group entries in the switch manager. Before deleting the lport, reset multicast mode to FM10K_XCAST_MODE_NONE to flush out these multicast-group entries. Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
The original comment may be read incorrectly as referring to checking the *entire* length is zero. However, it merely checks only the reserved bits of both length and reserved in a small amount of code. Update the comment to indicate this is a clever trick and clearly spell out that it only checks the reserve bits. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Use a new #define FM10K_VLAN_OVERRIDE even though we're using the exact same bit. The reason for this is clarity in the code, otherwise you can read FM10K_VLAN_CLEAR and think it should be removed. Also add a comment explaining why the FM10K_VLAN_OVERRIDE bit is set. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
The diagram represents bit layout of the multi-bit VLAN update message format. Typically these diagrams are drawn using some power of 2 as the base, to more easily grasp where fields split. Although the numbers above can make it somewhat easy to understand which bit you're looking at, it makes the break points not line up. Re-draw the numbers using base 8, and mark the bit values every 8 bits at the top. This should make it more easy to grasp the table quickly. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
fm10k_tlv_parse_attr is supposed to return FM10K_NOT_IMPLEMENTED for any TLV who's attribute id lies outside the range of results. It does not do this today. In addition, the documentation does not indicate that other attributes which are not implemented for a given TLV will be silently ignored. Fix this. Clean up the logic so that we don't rely on the fact that FM10K_NOT_IMPLEMENTED is greater than zero, as this can easily cause confusion. A future extension could look into some way of reporting unknown TLVs in order to make issues more easily discoverable. We can't just return FM10K_NOT_IMPLEMENTED here because we don't want to drop the entire message if it has an unknown TLV. While here, update the copyright year. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
fm10k_io_error_detected() does not need to call pci_disable_device(). In the cases where the reset needs to occur, the stack flow will result in calling fm10k_remove() which already disables the PCI device. If we leave the pci_disable_device(), we result in a warning about disabling an already disabled device. Many PCI drivers do call pci_disable_device() in their .error_detected() routines, but it does not appear to be required. In addition, these drivers have a check "is_pci_enabled()" call in their remove routines, which is how they chose to handle the duplicate device disable. This seems incorrect, since the PCI device structure is reference counted. It is very possible that the reference count for the PCI device could be greater than 1. In this case, you would remove the PCI device within the error_detected routine, reducing count to 1, then remove it again in the remove function, reducing it to zero. This would result in yet another disable somewhere else failing. Thus, we shouldn't be using is_pci_enabled() to check for this issue. Instead, just remove the extraneous pci_device_disable() found within the error_detected routine. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Currently, any error responses from the switch manager after an LPORT_MAP request are silently ignored. At most the mailbox message will be reported as an error. This can result in unexpected behavior when the switch manager has configured a port with zero bandwidth. Add support for reading the fm10k_swapi_error structure from LPORT_MAP responses. If the message contains the necessary TLV and has a non-zero error code, report link down, clear the dglort_map, and delay the next get_host_state call by a reasonable delay. Also log an error message indicating that the LPORT_MAP request failed. The delay ensures preventing an interrupt storm on the switch manager, and reduces the number of mailbox messages we send in this scenario drastically. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Ngai-Mint Kwan 提交于
Multicast mode checking is no longer a requirement to perform unicast and multicast address syncs. Specifically, a device operating in promiscuous and/or all multicast mode is not excluded. The issue occurs when the netdev is pre-configured to either multicast mode and is enabled for the first time. The multicast-group table in the Switch Manager will be missing obvious multicast entries associated to this netdev. Changes were also made to disallow unicast and multicast syncs with VLAN 0. The Switch Manager considers VLAN 0 to be an invalid entry. Requests with VLAN 0 by the netdev are only generated when the driver is freshly installed and the default VID is not set. Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
The 1588 support within fm10k does not work correctly with the current version of the switch management software, and likely never worked correctly to begin with. Remove support for PTP/1588. Update copyright year for all these files while we're touching them. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
During an AER action response, we were calling fm10k_close without holding the rtnl_lock() which could lead to possible RCU warnings being produced due to 64bit stat updates among other causes. Similarly, we need rtnl_lock() around fm10k_open during fm10k_io_resume. Follow the same pattern elsewhere in the driver and protect the entire open/close sequence. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Use DRV_SUMMARY, similar to DRV_VERSION so that we don't have to duplicate the driver summary in multiple places. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Alexander Duyck 提交于
This patch enables bulk free in Tx cleanup for fm10k and cleans up the boolean logic in the polling routines for fm10k in the hopes of avoiding any mix-ups similar to what occurred with i40e and i40evf. Signed-off-by: NAlexander Duyck <aduyck@mirantis.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
This change fixes an (ab)use of the ethtool stats API, which could result in corrupt memory or misleading stat output. The ethtool stats API is not robust enough to handle varying number of statistics due to how it requests the size and allocates memory. Remove the poorly conceived support originally added for extra debug statistics. In the future, a new stats API may open up the ability to display these statistics. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Reduce duplicate code and the amount of indentation by adding fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help add fm10k_stat structures to the ethtool stats callbacks. This helps increase ease of use for future stat additions, and increases code readability. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 14 4月, 2016 1 次提交
-
-
由 Jacob Keller 提交于
The VF uses a multi-bit update request to clear unused VLANs whenever it resets. However, an accident in a previous refector broke multi-bit updates for VFs, due to misreading a comment in fm10k_vf.c and attempting to reduce code duplication. The problem occurs because a multi-bit request has a non-zero length, and the PF would simply drop any request with the upper 16 bits set. We can't simply remove the check of the upper 16 bits and the call to fm10k_iov_select vid, because this would remove the checks for default VID and for ensuring no other VLANs can be enabled except pf_vid when it has been set. To resolve that issue, this revision uses the iov_select_vid when we have a single-bit update, and denies any multi-bit update when the VLAN was administratively set by the PF. This should be ok since the PF properly updates VLAN_TABLE when it assigns the PF vid. This ensures that requests to add or remove the PF vid work as expected, but a rogue VF could not use the multi-bit update as a loophole to attempt receiving traffic on other VLANs. Reported-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 06 4月, 2016 6 次提交
-
-
由 Jacob Keller 提交于
The fm10k driver used its own code for generating a default indirection table on device load, which was not the same as the default generated by ethtool when indir_size of 0 is passed to SRXFH. Take advantage of ethtool_rxfh_indir_default() and simplify code to write the redirection table to reduce some code duplication. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
s/funciton/function to resolve a typo, and cleanup grammar on a few comments regarding processing the VF mailboxes. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Fix a kernel panic that occurs during surprise removal. Clear the interface queue counts upon fm10k_init_msix_capability failure. This prevents further code (fm10k_update_stats etc.) from attempting to access unallocated queue vector or ring memory. [ 628.692648] BUG: unable to handle kernel NULL pointer dereference at 0000000000000068 [ 628.692805] IP: [<ffffffffa0475caf>] fm10k_update_stats+0x7f/0x2c0 [fm10k] [ 628.693173] PGD 0 [ 628.693759] Oops: 0000 [#1] SMP [ 628.699321] CPU: 10 PID: 8164 Comm: kworker/10:0 Tainted: G OE ------------ 3.10.0-327.el7.x86_64 #1 [ 628.700096] Hardware name: Supermicro X9DAi/X9DAi, BIOS 3.2 05/09/2015 [ 628.700894] Workqueue: pciehp-1 pciehp_power_thread [ 628.701686] task: ffff88086559c500 ti: ffff8808593c0000 task.ti: ffff8808593c0000 [ 628.702493] RIP: 0010:[<ffffffffa0475caf>] [<ffffffffa0475caf>] fm10k_update_stats+0x7f/0x2c0 [fm10k] [ 628.703310] RSP: 0018:ffff8808593c3b00 EFLAGS: 00010282 [ 628.704132] RAX: 0000000000000000 RBX: ffff880860760000 RCX: 0000000000000000 [ 628.704963] RDX: ffff880860760b08 RSI: 0000000000000000 RDI: 0000000000000000 [ 628.705794] RBP: ffff8808593c3b40 R08: 0000000000000000 R09: 0000000000000000 [ 628.706604] R10: 0000000000000000 R11: ffff880860760c40 R12: 0000000000000080 [ 628.707420] R13: ffff8808607608c0 R14: ffff880860779ec0 R15: ffff880860779f40 [ 628.708238] FS: 0000000000000000(0000) GS:ffff88086f000000(0000) knlGS:0000000000000000 [ 628.709071] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 628.709923] CR2: 0000000000000068 CR3: 000000000194a000 CR4: 00000000001407e0 [ 628.710752] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 628.711596] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 628.712438] Stack: [ 628.713255] ffff880860764458 ffff8808607608c0 ffff880860760000 ffff880860760000 [ 628.714088] 0000000000000080 ffff8808607608c0 ffff880860779ec0 ffff880860779f40 [ 628.714925] ffff8808593c3b88 ffffffffa04780c5 ffff880860764458 0000000a8163cb5b [ 628.715752] Call Trace: [ 628.716560] [<ffffffffa04780c5>] fm10k_down+0x155/0x1f0 [fm10k] [ 628.717367] [<ffffffffa0479958>] fm10k_close+0x28/0xd0 [fm10k] [ 628.718184] [<ffffffff81526365>] __dev_close_many+0x85/0xd0 [ 628.718986] [<ffffffff815264d8>] dev_close_many+0x98/0x120 [ 628.719764] [<ffffffff81527ab8>] rollback_registered_many+0xa8/0x230 [ 628.720527] [<ffffffff81527c80>] rollback_registered+0x40/0x70 [ 628.721294] [<ffffffff81529198>] unregister_netdevice_queue+0x48/0x80 [ 628.722052] [<ffffffff815291ec>] unregister_netdev+0x1c/0x30 [ 628.722816] [<ffffffffa04762b8>] fm10k_remove+0xd8/0xe0 [fm10k] [ 628.723581] [<ffffffff81328c7b>] pci_device_remove+0x3b/0xb0 [ 628.724340] [<ffffffff813f5fbf>] __device_release_driver+0x7f/0xf0 [ 628.725088] [<ffffffff813f6053>] device_release_driver+0x23/0x30 [ 628.725814] [<ffffffff81321fe4>] pci_stop_bus_device+0x94/0xa0 [ 628.726535] [<ffffffff813220d2>] pci_stop_and_remove_bus_device+0x12/0x20 [ 628.727249] [<ffffffff8133de40>] pciehp_unconfigure_device+0xb0/0x1b0 [ 628.727964] [<ffffffff8133d822>] pciehp_disable_slot+0x52/0xd0 [ 628.728664] [<ffffffff8133d98a>] pciehp_power_thread+0xea/0x150 [ 628.729358] [<ffffffff8109d5fb>] process_one_work+0x17b/0x470 [ 628.730036] [<ffffffff8109e3cb>] worker_thread+0x11b/0x400 [ 628.730730] [<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400 [ 628.731385] [<ffffffff810a5aef>] kthread+0xcf/0xe0 [ 628.732036] [<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140 [ 628.732674] [<ffffffff81645858>] ret_from_fork+0x58/0x90 [ 628.733289] [<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140 [ 628.733883] Code: 83 e8 01 48 8d 97 40 02 00 00 45 31 c0 4c 8d 9c c7 48 02 0 [ 628.735202] RIP [<ffffffffa0475caf>] fm10k_update_stats+0x7f/0x2c0 [fm10k] [ 628.735732] RSP <ffff8808593c3b00> [ 628.736285] CR2: 0000000000000068 [ 628.736846] ---[ end trace 9156088b311aff42 ]--- Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Bruce Allan 提交于
If 'attr_flag < (1 << (2 * FM10K_TEST_MSG_NESTED))' is ever false, err will be used uninitialized. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
Reduce duplicate code and the amount of indentation by adding fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help add fm10k_stat structures to the ethtool stats callbacks. This helps increase ease of use for future stat additions, and increases code readability. Skip handling of the per-queue stats as these will be reworked in a following patch. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
During fm10k_io_error_detected we were clearing the interrupt scheme before we freed the MBX IRQ. This causes a kernel panic because the MBX IRQ are assigned after MSI-X initialization. Clearing the interrupt scheme results in removing the MSI-X entry table. Fix this by freeing the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in the driver. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-