opcode to be accessed is in le16 format so convert it
first to cpu byte order.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Use struct hci_cp_write_def_link_policy to overcome sparse
warnigs below:

...
net/bluetooth/hci_event.c:633:21: warning: incorrect type in assignment
(different base types)
net/bluetooth/hci_event.c:633:21:    expected unsigned short [unsigned]
[assigned] [usertype] link_policy
net/bluetooth/hci_event.c:633:21:    got restricted __le16 [usertype] <noident>
...
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fix sparse warnigns below:
...
net/bluetooth/hci_sysfs.c:458:33: warning: cast to restricted __be32
net/bluetooth/hci_sysfs.c:458:47: warning: cast to restricted __be16
...
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In L2CAP we use le16 format so change direction of conversion
from le16_to_cpu to cpu_to_le16.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Create Chan Rsp shall put result and status in le format.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

L2CAP channel id is used in host format in internal L2CAP code.
Fix sparse warnings about wrong endian conversion.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

cmd->len is in le format so convert it to host format before use.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

ediv is already in little endian order.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In case the struct is already __packed, there is no need to use
unaligned access to the data. So just use cpu_to_le16 or
__constant_cpu_to_le16 in these cases.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Device ID details need to be programmed into the kernel for every
controller at least once. So provide management command for this.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Device ID information can be provided via Extended Inquiry Data
as well. If a valid source is present, then include it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Inquiry Response TX power tag should be added to the Extended
Inquiry Data (EIR) as well.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

We initialize the "struct device" in hci_alloc_dev() for a long time now
so we can access hdev->dev.parent directly. Hence, we can drop the
temporary field hdev->parent which is used in no other place than
hci_add_sysfs().

SET_HCIDEV_DEV() is never called after registering a device by the
drivers so we do not overwrite internal device-state. Furthermore,
hdev->dev is initialized to 0 by kzalloc() inside hci_alloc_dev() so the
default behavior with dev.parent = NULL is kept.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In order to do interleaved discovery we should be in DISCOVERY_
FINDING state. Otherwise, discovery should be stopped.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

chan->psm is kept in __le16 format which was not always taken
into account. Fix several bugs related to extra conversion.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Value to be converted is already in __le32 format.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Correct type warnings reported by sparse to show that this
functions takes ediv argument in __le16 format.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Correct endian conversion reported by sparse
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we have protection enabled, allow non-HT and HT20 stations to peer
with HT40+/- stations. Peering is still disallowed for HT40+/- mismatch.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Section 9.23.3.5 of IEEE 80211s standard describes the protection rules for
HT mesh STA in a MBSS. Three HT protection modes are supported for now:

non-HT mixed mode - is selected if any non-HT peers are present in our MBSS.
20MHz-protection mode - is selected if all peers in our 20/40MHz MBSS support
			HT and atleast one HT20 peer is present.
no-protection mode - is selected otherwise.

This is a limited implementation of 9.23.3.5, which only considers mesh peers
when determining the HT protection mode. Station's channel_type needs to be
maintained.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the BSS table is organized in a RB tree, the BSSs need to be
comparable. This means that we must define a < and > operator to
the BSS object.
compare_ethr_addr isn't enough since it returns only a binary value.

Since Felix's

cfg80211: use compare_ether_addr on MAC addresses instead of memcmp

    Because of the constant size and guaranteed 16 bit alignment, the inline
    compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The BSS table is corrupted: rb_find_bss can't find the bss.
As a result BSSes are duplicated in the BSS table, and we get stuck
while probing an AP before associating (in STA mode).

Change-Id: I85928756f4328028230832c1565ece7f412f3843
CC: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable.  This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds hooks to call into the driver to get additional
stats for the ethtool API.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This lets ethtool print out stats related to stations
connected to the interface.  Does not yet get stats
from the underlying driver.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a mesh peer indicates it is operating as 20MHz-only in its HT
operation IE, have the rate control algorithm respect this by disabling
the equivalent bit in the ieee80211_sta HT capabilities.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers need the station rate info when inserting a new sta_info. The
patch "mac80211: refactor mesh peer initialization" wrongly assumed the
rate info could be applied after insertion. After further review, this
is clearly not the case.

This fixes a regression where HT parameters were not applied before
inserting the sta_info, causing performance degradation.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rate control updation never be called on 2040 BSS change.
The station should update its rate control on receiving beacon
with different HT mode in the HT operation IE. Not doing so,
leads to sending frames with higher(ht40) rates whereas AP is
operating in lower mode (ht20).
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.

This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.

Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Explicit helper attachment via the CT target is broken with NAT
if non-standard ports are used. This problem was hidden behind
the automatic helper assignment routine. Thus, it becomes more
noticeable now that we can disable the automatic helper assignment
with Eric Leblond's:

9e8ac5a netfilter: nf_ct_helper: allow to disable automatic helper assignment

Basically, nf_conntrack_alter_reply asks for looking up the helper
up if NAT is enabled. Unfortunately, we don't have the conntrack
template at that point anymore.

Since we don't want to rely on the automatic helper assignment,
we can skip the second look-up and stick to the helper that was
attached by iptables. With the CT target, the user is in full
control of helper attachment, thus, the policy is to trust what
the user explicitly configures via iptables (no automatic magic
anymore).

Interestingly, this bug was hidden by the automatic helper look-up
code. But it can be easily trigger if you attach the helper in
a non-standard port, eg.

iptables -I PREROUTING -t raw -p tcp --dport 8888 \
	-j CT --helper ftp

And you disabled the automatic helper assignment.

I added the IPS_HELPER_BIT that allows us to differenciate between
a helper that has been explicitly attached and those that have been
automatically assigned. I didn't come up with a better solution
(having backward compatibility in mind).
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

This refreshes the "timeout" attribute in existing expectations if one is
given.

The use case for this would be for userspace helpers to extend the lifetime
of the expectation when requested, as this is not possible right now
without deleting/recreating the expectation.

I use this specifically for forwarding DCERPC traffic through:

DCERPC has a port mapper daemon that chooses a (seemingly) random port for
future traffic to go to. We expect this traffic (with a reasonable
timeout), but sometimes the port mapper will tell the client to continue
using the same port. This allows us to extend the expectation accordingly.
Signed-off-by: NKelvie Wong <kelvie@ieee.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

To build ip_vs as a module sysctl_rmem_max and sysctl_wmem_max
needs to be exported.

The dependency was added by "ipvs: wakeup master thread" patch.
Signed-off-by: NHans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.

This quiets the sparse warnings:

warning: symbol '__ipvs_proto_data_get' was not declared. Should it be static?
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.

This quiets the sparse warnings:

warning: symbol 'ip_vs_ftp_init' was not declared. Should it be static?
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

	cp->flags is marked volatile but ip_vs_bind_dest
can safely modify the flags, so save some CPU cycles by
using temp variable.
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NSimon Horman <horms@verge.net.au>

	Allow master and backup servers to use many threads
for sync traffic. Add sysctl var "sync_ports" to define the
number of threads. Every thread will use single UDP port,
thread 0 will use the default port 8848 while last thread
will use port 8848+sync_ports-1.

	The sync traffic for connections is scheduled to many
master threads based on the cp address but one connection is
always assigned to same thread to avoid reordering of the
sync messages.

	Remove ip_vs_sync_switch_mode because this check
for sync mode change is still risky. Instead, check for mode
change under sync_buff_lock.

	Make sure the backup socks do not block on reading.

Special thanks to Aleksey Chudov for helping in all tests.
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Tested-by: NAleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

	Add two new sysctl vars to control the sync rate with the
main idea to reduce the rate for connection templates because
currently it depends on the packet rate for controlled connections.
This mechanism should be useful also for normal connections
with high traffic.

sync_refresh_period: in seconds, difference in reported connection
	timer that triggers new sync message. It can be used to
	avoid sync messages for the specified period (or half of
	the connection timeout if it is lower) if connection state
	is not changed from last sync.

sync_retries: integer, 0..3, defines sync retries with period of
	sync_refresh_period/8. Useful to protect against loss of
	sync messages.

	Allow sysctl_sync_threshold to be used with
sysctl_sync_period=0, so that only single sync message is sent
if sync_refresh_period is also 0.

	Add new field "sync_endtime" in connection structure to
hold the reported time when connection expires. The 2 lowest
bits will represent the retry count.

	As the sysctl_sync_period now can be 0 use ACCESS_ONCE to
avoid division by zero.

	Special thanks to Aleksey Chudov for being patient with me,
for his extensive reports and helping in all tests.
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Tested-by: NAleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

	High rate of sync messages in master can lead to
overflowing the socket buffer and dropping the messages.
Fixed sleep of 1 second without wakeup events is not suitable
for loaded masters,

	Use delayed_work to schedule sending for queued messages
and limit the delay to IPVS_SYNC_SEND_DELAY (20ms). This will
reduce the rate of wakeups but to avoid sending long bursts we
wakeup the master thread after IPVS_SYNC_WAKEUP_RATE (8) messages.

	Add hard limit for the queued messages before sending
by using "sync_qlen_max" sysctl var. It defaults to 1/32 of
the memory pages but actually represents number of messages.
It will protect us from allocating large parts of memory
when the sending rate is lower than the queuing rate.

	As suggested by Pablo, add new sysctl var
"sync_sock_size" to configure the SNDBUF (master) or
RCVBUF (slave) socket limit. Default value is 0 (preserve
system defaults).

	Change the master thread to detect and block on
SNDBUF overflow, so that we do not drop messages when
the socket limit is low but the sync_qlen_max limit is
not reached. On ENOBUFS or other errors just drop the
messages.

	Change master thread to enter TASK_INTERRUPTIBLE
state early, so that we do not miss wakeups due to messages or
kthread_should_stop event.

Thanks to Pablo Neira Ayuso for his valuable feedback!
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NSimon Horman <horms@verge.net.au>