* pxa-plat: (53 commits)
  [ARM] 4762/1: Basic support for Toradex Colibri module
  [ARM] pxa: fix mci_init functions returning -1
  [ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
  [ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270
  [ARM] 4746/1: pcm027: network support for phyCORE-PXA270
  [ARM] 4745/1: pcm027: default configuration
  [ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module
  [NET] smc91x: Make smc91x use IRQ resource trigger flags
  [ARM] pxa: add default config for littleton
  [ARM] pxa: add basic support for Littleton (PXA3xx Form Factor Platform)
  [ARM] 4664/1: Add basic support for HTC Magician PDA phones
  [ARM] 4649/1: Base support for pxa-based Toshiba e-series PDAs.
  [ARM] pxa: skip registers saving/restoring if entering standby mode
  [ARM] pxa: fix PXA27x resume
  [ARM] pxa: Avoid fiddling with CKEN register on suspend
  [ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme
  [ARM] pxa: Add zylonite MFP wakeup configurations
  [ARM] pxa: program MFPs for low power mode when suspending
  [ARM] pxa: make MFP configuration processor independent
  [ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functions
  ...

Conflicts:

	arch/arm/mach-pxa/ssp.c
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* orion: (26 commits)
  [ARM] Orion: implement power-off method for QNAP TS-109/209
  [ARM] Orion: add support for QNAP TS-109/TS-209
  [ARM] Orion: I2C support
  [I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
  [I2C] Split mv643xx I2C platform support
  [ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
  [ARM] Orion defconfig
  [ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
  [ARM] Orion: MV88F5181 support bits
  [ARM] Orion: Buffalo/Revogear Kurobox Pro support
  [ARM] OrionNAS RD board support
  [ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
  [ARM] Orion: common platform setup for Gigabit Ethernet port
  [ARM] Orion: platform device registration for UART, USB and NAND
  [ARM] Orion: system timer support
  [ARM] Orion edge GPIO IRQ support
  [ARM] Orion: IRQ support
  [ARM] Orion: provide GPIO method for enabling hardware assisted blinking
  [ARM] Orion: GPIO support
  [ARM] Orion: programable address map support
  ...

Conflicts:

	arch/arm/Kconfig
	arch/arm/Makefile
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge branches 'at91', 'ep93xx', 'iop', 'kprobes', 'ks8695', 'misc', 'msm', 's3c2410', 'sa1100' and 'vfp' into devel

* at91: (24 commits)
  [ARM] 4615/4: sam926[13]ek buttons updated
  [ARM] 4765/1: [AT91] AT91CAP9A-DK board support
  [ARM] 4764/1: [AT91] AT91CAP9 core support
  [ARM] 4738/1: at91sam9261: Remove udc pullup enabling in board initialisation
  [ARM] 4761/1: [AT91] Board-support for NEW_LEDs
  [ARM] 4760/1: [AT91] SPI CS0 errata on AT91RM9200
  [ARM] 4759/1: [AT91] Buttons on CSB300
  [ARM] 4758/1: [AT91] LEDs
  [ARM] 4757/1: [AT91] UART initialization
  [ARM] 4756/1: [AT91] Makefile cleanup
  [ARM] 4755/1: [AT91] NAND update
  [ARM] 4754/1: [AT91] SSC library support
  [ARM] 4753/1: [AT91] Use DMA_BIT_MASK
  [ARM] 4752/1: [AT91] RTT, RTC and WDT peripherals on SAM9
  [ARM] 4751/1: [AT91] ISI peripheral on SAM9263
  [ARM] 4750/1: [AT91] STN LCD displays on SAM9261
  [ARM] 4734/1: at91sam9263ek: include IRQ for Ethernet PHY
  [ARM] 4646/1: AT91: configurable HZ, default to 128
  [ARM] 4688/1: at91: speed-up irq processing
  [ARM] 4657/1: AT91: Header definition update
  ...

* ep93xx:
  [ARM] 4671/1: ep93xx: remove obsolete gpio_line_* operations
  [ARM] 4670/1: ep93xx: implement IRQT_BOTHEDGE gpio irq sense type
  [ARM] 4669/1: ep93xx: simplify GPIO code and cleanups
  [ARM] 4668/1: ep93xx: implement new GPIO API

* iop:
  [ARM] 4770/1: GLAN Tank: correct physmap_flash_data width field
  [ARM] 4732/1: GLAN Tank: register rtc-rs5c372 i2c device
  [ARM] 4708/1: iop: update defconfigs for 2.6.24

* kprobes:
  ARM kprobes: let's enable it
  ARM kprobes: special hook for the kprobes breakpoint handler
  ARM kprobes: prevent some functions involved with kprobes from being probed
  ARM kprobes: don't let a single-stepped stmdb corrupt the exception stack
  ARM kprobes: add the kprobes hook to the page fault handler
  ARM kprobes: core code
  ARM kprobes: instruction single-stepping support

* ks8695:
  [ARM] 4603/1: KS8695: debugfs interface to view pin state
  [ARM] 4601/1: KS8695: PCI support

* misc:
  [ARM] remove duplicate includes
  [ARM] CONFIG_DEBUG_STACK_USAGE
  [ARM] 4689/1: small comment wrap fix
  [ARM] 4687/1: Trivial arch/arm/kernel/entry-common.S comment fix
  [ARM] 4666/1: ixp4xx: fix sparse warnings in include/asm-arm/arch-ixp4xx/io.h
  [ARM] remove reference to non-existent MTD_OBSOLETE_CHIPS
  [SERIAL] 21285: Report baud rate back via termios
  [ARM] Remove pointless casts from void pointers,
  [ARM] Misc minor interrupt handler cleanups
  [ARM] Remove at91_lcdc.h
  [ARM] ARRAY_SIZE() cleanup
  [ARM] Update mach-types

* msm:
  [ARM] msm: dma support for MSM7X00A
  [ARM] msm: board file for MACH_HALIBUT (QCT MSM7200A)
  [ARM] msm: irq and timer support for ARCH_MSM7X00A
  [ARM] msm: core platform support for ARCH_MSM7X00A

* s3c2410: (33 commits)
  [ARM] 4795/1: S3C244X: Add armclk and setparent call
  [ARM] 4794/1: S3C24XX: Comonise S3C2440 and S3C2442 clock code
  [ARM] 4793/1: S3C24XX: Add IRQ->GPIO pin mapping function
  [ARM] 4792/1: S3C24XX: Remove warnings from debug-macro.S
  [ARM] 4791/1: S3C2412: Make fclk a parent of msysclk
  [ARM] 4790/1: S3C2412: Fix parent selection for msysclk.
  [ARM] 4789/1: S3C2412: Add missing CLKDIVN register values
  [ARM] 4788/1: S3C24XX: Fix paramet to s3c2410_dma_ctrl if S3C2410_DMAF_AUTOSTART used.
  [ARM] 4787/1: S3C24XX: s3c2410_dma_request() should return the allocated channel number
  [ARM] 4786/1: S3C2412: Add SPI FIFO controll constants
  [ARM] 4785/1: S3C24XX: Add _SHIFT definitions for S3C2410_BANKCON registers
  [ARM] 4784/1: S3C24XX: Fix GPIO restore glitches
  [ARM] 4783/1: S3C24XX: Add s3c2410_gpio_getpull()
  [ARM] 4782/1: S3C24XX: Define FIQ_START for any FIQ users
  [ARM] 4781/1: S3C24XX: DMA suspend and resume support
  [ARM] 4780/1: S3C2412: Allow for seperate DMA channels for TX and RX
  [ARM] 4779/1: S3C2412: Add s3c2412_gpio_set_sleepcfg() call
  [ARM] 4778/1: S3C2412: Add armclk and init from DVS state
  [ARM] 4777/1: S3C24XX: Ensure clk_set_rate() checks the set_rate method for the clk
  [ARM] 4775/1: s3c2410: fix compilation error if only s3c2442 cpu is selected
  ...

* sa1100:
  [ARM] sa1100: add clock source support

* vfp:
  [ARM] 4584/2: ARMv7: Add Advanced SIMD (NEON) extension support
  [ARM] 4583/1: ARMv7: Add VFPv3 support
  [ARM] 4582/2: Add support for the common VFP subarchitecture

Add armclk to the supported clocks on the S3C2440 and S3C2442 to
better represent the DVS state which controls whether FCLK or HCLK
is fed to the ARM core.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge together the bits of the S3C2440 and S3C2442 clock code
that can be.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the reverse of s3c2410_gpio_getirq to convert
a IRQ  number into a GPIO pin number.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove warnings left in include/asm-arm/arch-s3c2410/debug-macro.S
whilst these where being experimented with.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In the S3C2412 fclk is derived from msysclk, not straight from
the MPLL output. Set clk_f.parent appropriately.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The msysclk clock was checking for the wrong PLL for the
parent in s3c2412_setparent_msysclk(), trying the UPLL instead
of the MPLL output.

Also ensure the mpll and fclks are at the same rate at init time.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add S3C2412_CLKDIVN_DVSEN and S3C2412_CLKDIVN_HALFHCLK definitions to
the S3C2412_CLKDIVN set.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the channel parameter to s3c2410_dma_ctrl() in s3c2410_dma_enqueue()
if the S3C2410_DMAF_AUTOSTART is set on the channel.

Spotted by Steven Ryu at Samsung.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The s3c2410_dma_request() function should return the channel allocated
instead of zero for success.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add control constants for the S3C2412 SPI unit FIFO.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add definitions to allow easier decomposotion of the contents of
the S3C2410_BANKON registers
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The core resume code may have caused glitches in the GPIO when
restoring the GPIO state due to the order in which the GPIO registers
were being written.

Change the restore process take into account the state of the
GPIOs on resume and the state the system wants to restore them to.

See the code comments in the patch for more details of the process.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the call s3c2410_gpio_getpull() to return the
current state of the pin's pull-up.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure FIQ_START is defined to allow anyone to use FIQ code on
an S3C24XX based CPU.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.

Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: NBen Dooks <ben-linux@flfuf.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.

This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep
configuration of the GPIO blocks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add armclk to the S3C2412 to indicate the current clock connected to
the ARM core.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add checks for clk_set_rate() and ensure that we do not allow set_rate
to be called for a clock that does not have it defined. Add default
methods for fclk, hclk, pclk and mpll.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch fixes compilation error if only a machine with
s3c2442 cpu is selected but without s3c2440 cpu selected.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Check if the sleep command returns due to a pending interrupt
in the standby unit. If this happens, try and ack the IRQ
before re-trying the resume.

It is currently unclear whether the resume can be backed out
of at this stage as this could cause a problem with level
based interrupts.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The S3C2412 IIS engine differs from the previous
SoC in the range, so add a set of register definitions
in a seperate file for it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The IIS and SDI register hw_addr definitions are
incorrect in the DMA map for the S3C2412.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The S3C2412 GPIO is similar enough to the S3C2410 that
it can use it as a base for GPIO functionality.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We have a default display set to 4, when we only have
three registered displays. Fix this argument (a seperate
patch has been generated to ensure that the LCD driver
takes notice of this bug)
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If the watchdog reset fails and we decided to take the jump
to zero approach, allow 50ms for the UARTS to drain the FIFOs
before calling into a bootloader that may flush the output.

Also reduece the waits and the timeout values as 5 seconds is
rather long.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If the hard reset routine is using the watchdog, then
ensure that the clock for the watchdog has been enabled
before we try and issue a reset.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the S3C2412_PWRCFG values for the action taken on detecting that
the battery is flat.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add S3C2412 register definitions.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix all those PXA mci_init functions which return -1 rather than
propagating the error code to the higher levels.  Remove the silly
set_irq_type() calls as well - use the flags for request_irq()
instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.

Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.

The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.

An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds baseboard support for the phyCORE-PXA270 development
kit (aka PCM-990).

This example shows how to use some phyCORE-PXA270 CPU module features
on a baseboard in a standard manner. It could be used as a starting
point for custom baseboard development.

V2:
 After comments by Eric Miao:
  - IRQ chained handler fixed
  - video/graphic support moved to separate patch
  - ifdef/endif hell reduced ;-)

V3:
 After comments by Russell King
  - initialise the mmci platform data statically

V4:
 After comments by Russell King
  - wrong return value in pcm990_mci_init() fixed
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>