- 08 7月, 2012 7 次提交
-
-
由 Hadar Hen Zion 提交于
The driver is modified to support three operation modes. If supported by firmware use the device managed flow steering API, that which we call device managed steering mode. Else, if the firmware supports the B0 steering mode use it, and finally, if none of the above, use the A0 steering mode. When the steering mode is device managed, the code is modified such that L2 based rules set by the mlx4_en driver for Ethernet unicast and multicast, and the IB stack multicast attach calls done through the mlx4_ib driver are all routed to use the device managed API. When attaching rule using device managed flow steering API, the firmware returns a 64 bit registration id, which is to be provided during detach. Currently the firmware is always programmed during HCA initialization to use standard L2 hashing. Future work should be done to allow configuring the flow-steering hash function with common, non proprietary means. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hadar Hen Zion 提交于
Add support for firmware commands to attach/detach a new device managed steering mode. Such network steering rules allow the user to provide an L2/L3/L4 flow specification to the firmware and have the device to steer traffic that matches that specification to the provided QP. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hadar Hen Zion 提交于
Instead of checking the firmware supported steering mode in various places in the code, add a dedicated field in the mlx4 device capabilities structure which is written once during the initialization flow and read across the code. This also set the grounds for add new steering modes. Currently two modes are supported, and are named after the ConnectX HW versions A0 and B0. A0 steering uses mac_index, vlan_index and priority to steer traffic into pre-defined range of QPs. B0 steering uses Ethernet L2 hashing rules and is enabled only if the firmware supports both unicast and multicast B0 steering, The current steering modes are relevant for Ethernet traffic only, such that Infiniband steering remains untouched. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
Currently, for every change in the net device multicast list, the driver detaches all the addresses from the HW device, and then attaches the updated list. This behavior is wrong from two aspects: first, it causes a load of firmware commands and second, there is period of time where the correct addresses are not attached, which turned into packet loss. To improve - a copy of the multicast list is saved by the driver. For every change in the multicast list, the multicast list copy is used to find the delta between those two lists and add or remove multicast addresses as needed. Reported-by: NShawn Bohrer <sbohrer@rgmadvisors.com> Cc: Shawn Bohrer <sbohrer@rgmadvisors.com> Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hadar Hen Zion 提交于
Currently the IDs used by the resource tracker are of type u32, so far this was ok since all the different resources we were tracking could be encoded in 32bit. As a preparation step for tracking of resources whose IDs need > 32 bits such as network flow steering rules, who are 64 bit in size, move to use 64 bit based resource IDs. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hadar Hen Zion 提交于
Change the data structure used for managing the SRIOV resource tracking mechanism from radix tree to red-black tree. This is preparation step for supporting resource IDs which are 64bit long, such as network flow steering rules. Such IDs can't be used as radix-tree keys on 32bit architectures and hence the reason for the change. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Devendra Naga 提交于
pci_set_drvdata is called twice at the remove path of driver, call it once. Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 7月, 2012 12 次提交
-
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Jon Mason <mason@myri.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Divy Le Ray <divy@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Divy Le Ray <divy@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Cc: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Jon Mason <jdmason@kudzu.us> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This means passing in a suitable destination address. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 7月, 2012 4 次提交
-
-
由 Giuseppe CAVALLARO 提交于
This patch adds the Energy Efficient Ethernet support to the stmmac. Please see the driver's documentation for further details about this support in the driver. Thanks also goes to Rayagond Kokatanur for his first implementation. Note: to clearly manage and expose the lpi interrupt status and eee ethtool stats I've had to do some modifications to the driver's design and I found really useful to move other parts of the code (e.g. mmc irq stat) in the main directly. So this means that some core has been reworked to introduce the EEE. v1: initial patch v2: fixed some sparse issues (typos) v3: erroneously sent the v2 renamed as v3 v4: o Fixed the return value of the stmmac_eee_init as suggested by D.Miller o Totally reviewed the ethtool support for EEE o Added a new internal parameter to tune the SW timer for TX LPI. v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails (it has to return -EOPNOTSUPP in that case). Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe CAVALLARO 提交于
This patch replaces the obsolete strict_strtoul with kstrtoint. v2: also removed casting on kstrtoul. v3: use kstrtoint instead of kstrtoul due to all vars are integer. thanks to E. Dumazet. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
Currently only used when packet split mode is enabled with jumbo frames, IP payload checksum (for fragmented UDP packets) is mutually exclusive with receive hashing offload since the hardware uses the same space in the receive descriptor for the hardware-provided packet checksum and the RSS hash, respectively. Users currently must disable jumbos when receive hashing offload is enabled, or vice versa, because of this incompatibility. Since testing has shown that IP payload checksum does not provide any real benefit, just remove it so that there is no longer a choice between jumbos or receive hashing offload but not both as done in other Intel GbE drivers (e.g. e1000, igb). Also, add a missing check for IP checksum error reported by the hardware; let the stack verify the checksum when this happens. CC: stable <stable@vger.kernel.org> [3.4] Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Mitch A Williams 提交于
Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero. Refactor this function to fix this issue and make it more clear what the intent of each conditional is. Add comment regarding using a setting of zero. CC: stable <stable@vger.kernel.org> [3.3+] CC: David Ahern <daahern@cisco.com> Signed-off-by: NMitch Williams <mitch.a.williams@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 6月, 2012 1 次提交
-
-
由 Michael Chan 提交于
commit 1f85d58c cnic: Remove uio mem[0]. introduced a regression as older versions of userspace app still rely on this mmap. Restore the mmap functionality and get the base address from pci_resource_start() as the nedev->base_addr has been deprecated for PCI devices. Update version to 2.5.12. Signed-off-by: NMichael Chan <mchan@broadocm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 6月, 2012 3 次提交
-
-
由 Manish chopra 提交于
o Set the ethtool_dump flag (=ETH_FW_DUMP_DISABLE) when dump is disabled. o update driver version to 4.0.80 Signed-off-by: NManish chopra <manish.chopra@qlogic.com> Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Mack 提交于
This fixes a number of warnings such as: CC drivers/net/ethernet/ti/davinci_cpdma.o drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition has no type or storage class drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’ drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names (without types) in function declaration Signed-off-by: NDaniel Mack <zonque@gmail.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: David S. Miller <davem@davemloft.net> Cc: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Claudiu Manoil 提交于
The correct behavior is to program the interrupt coalescing regs (RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing" flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue then the corresponding coalescing register should be cleared. This behavior is correctly implemented for the single-queue mode (SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE). This fixes the later case. Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 6月, 2012 10 次提交
-
-
由 Shawn Guo 提交于
Different boards may require different phy reset duration. Add property phy-reset-duration for device tree probe, so that the boards that need a longer reset duration can specify it in their device tree. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
Using gpio_request_one will require the probe fail-out call gpio_free, which is missing currently. Change to use devm_gpio_request_one to fix the problem. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
If bootloader or platform initialization code does not enable the power supply to fec phy, we need to do it in fec driver before calling fec_reset_phy to have the phy powered on. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
In case that bootloader or platform initialization does not set up fec pins, the fec_reset_phy will not be able to succeed, because fec_reset_phy is currently called before devm_pinctrl_get_select_default. Move fec_reset_phy call to the place between devm_pinctrl_get_select_default and fec_enet_init to have above case be taken care. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
to stop all tx queues. Update version to 2.2.3. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
to indicate that the mising break statements are intended. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eddie Wai 提交于
If firmware returns error status, proceed to close the iSCSI connection. Update version to 2.5.11. Signed-off-by: NEddie Wai <eddie.wai@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
This memory region is no longer used. Userspace gets the BAR address directly from sysfs. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eddie Wai 提交于
so that it will work on any hypervisor. Signed-off-by: NEddie Wai <eddie.wai@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
We register with bnx2x before we allocate ctx_tbl structure, so it is possible for bnx2x to call cnic_ctl before the structure is allocated. This can sometimes cause NULL pointer dereference of cp->ctx_tbl. We fix this by adding simple checking for valid state before proceeding. The cnic_ctl call is RCU protected so we don't have to deal with race conditions. Because of the additional checking, we need to finish the shutdown before clearing the CNIC_UP flag. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 6月, 2012 3 次提交
-
-
由 Somnath Kotur 提交于
Fixed spelling error in a comment as pointed out by DaveM. Also refactored existing code a bit to provide placeholders for another ASIC Bug workaround that will be checked-in soon after this. Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
This patch supports the ethtool's set_ringparam() and get_ringparam(). Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
After freeing the buffer, the driver should change the value of the pointer to NULL. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-