The long term keys should only be stored when they belong to an
indentity address. The identity address can either be a public
address or a random static address.

For all other addresses (unresovable or resolvable) tell userspace
that the long term key is not persistent.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The long term keys should be associated with an identity address. Valid
identity addresses are public addresses or static addresses. So only
allow these two as valid address information for long term keys.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add support for IMC Networks (Broadcom based) to btusb driver.

Below the output of /sys/kernel/debug/usb/devices for this device:

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3404 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=240A649F8246
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NJurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The skb truesize of a 12-byte payload with a 10-byte head/tail
reserve is 768 bytes. Consequently, even with 40 tx_credits, at
most 6 packets could be queued at any one time:

  40 tx_credits * 127-byte mtu < 768-byte truesize * 7

This error could also cause the tx queue to apparently stall if
credit flow control is disabled (where tx_credits is fixed at 5),
or if the receiver only granted a limited number of tx credits
(eg., less than 7).

Instead, track the outstanding number of queued packets not yet sent
in wmem_alloc and allow for a maximum of 40 queued packets. Report
the space avail for a single write() as the mtu * number of packets
left before reaching the maximum.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Compute the amount of space available for a single write()
within rfcomm_room(); clamp to 0 for negative values. Note
this patch does not change the result of the computation.

Report the amount of room returned in the debug printk.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The tty driver api design prefers no-fail writes if the driver
write_room() method has previously indicated space is available
to accept writes. Since this is trivially possible for the
RFCOMM tty driver, do so.

Introduce rfcomm_dlc_send_noerror(), which queues but does not
schedule the krfcomm thread if the dlc is not yet connected
(and thus does not error based on the connection state).
The mtu size test is also unnecessary since the caller already
chunks the written data into mtu size.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If rfcomm_dlc_open() fails, set tty into error state which returns
-EIO from reads and writes.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If RFCOMM tty device registration fails, cleanup by releasing
the tty_port reference to trigger rfcomm_dev destruction
(rather than open-coding it).

The dlc reference release is moved into rfcomm_dev_add(),
which ensures cleanup in both error paths -- ie., if
__rfcomm_dev_add() fails or if tty_port_register_device() fails.

Fixes releasing the module reference if device registration fails.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Move rfcomm_dev allocation and initialization into new function,
__rfcomm_dev_add(), to simplify resource release in error handling.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

At least two different race conditions exist with multiple concurrent
RFCOMMCREATEDEV and RFCOMMRELEASEDEV ioctls:
* Multiple concurrent RFCOMMCREATEDEVs with RFCOMM_REUSE_DLC can
  mistakenly share the same DLC.
* RFCOMMRELEASEDEV can destruct the rfcomm_dev still being
  constructed by RFCOMMCREATEDEV.

Introduce rfcomm_ioctl_mutex to serialize these add/remove operations.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Functions which search lists for matching id's are more
commonly named *_lookup, which is the convention in the
bluetooth core as well.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The RFCOMM tty device is parented to the acl link device when
the dlc state_change(BT_CONNECTED) notification is received.
However, if the dlc from the RFCOMM socket is being reused
(RFCOMM_REUSE_DLC is set), then the dlc may already be connected,
and no notification will occur.

Instead, always parent the RFCOMM tty device to the acl link
device at registration time. If the acl link device is not available
(eg, because the dlc is not connected) then the tty will remain
unparented until the BT_CONNECTED notification is received.

Fixes regression with ModemManager when the rfcomm device is
created with the flag RFCOMM_REUSE_DLC.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Accessing the results of hci_conn_hash_lookup_ba() is unsafe without
holding the hci_dev_lock() during the lookup. For example:

CPU 0                             | CPU 1
hci_conn_hash_lookup_ba           | hci_conn_del
  rcu_read_lock                   |   hci_conn_hash_del
  list_for_each_entry_rcu         |     list_del_rcu
    if (.....)                    |       synchronize_rcu
      rcu_read_unlock             |
                                  |   hci_conn_del_sysfs
                                  |   hci_dev_put
                                  |   hci_conn_put
                                  |     put_device (last reference)
                                  |       bt_link_release
                                  |         kfree(conn)
      return p  << just freed     |

Even if a hci_conn reference were taken (via hci_conn_get), would
not guarantee the lifetime of the sysfs device, but only safe
access to the in-memory structure.

Ensure the hci_conn device stays valid while the rfcomm device
is reparented; rename rfcomm_get_device() to rfcomm_reparent_device()
and perform the reparenting within the function while holding the
hci_dev_lock.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If the RFCOMM session has not yet been started (ie., session is
still in BT_BOUND state) when a dlc is closed, directly close and
unlink the dlc rather than sending a DISC frame that is never
sent.

This allows the dlci to be immediately reused rather than waiting
for a 20 second timeout.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Prepare for directly closing dlc if the RFCOMM session has not
yet been started; refactor the dlc disconnect logic into a separate
local function, __rfcomm_dlc_disconn(). Retains functional
equivalence.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Prepare for directly closing dlc if the RFCOMM session has not
yet been started; refactor the deferred setup test for only those
dlc states to which the test applies. Retains functional
equivalence.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Merge conditional test for BT_LISTEN session state into following
switch statement (which is functionally equivalent).
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Only one session/channel combination may be in use at any one
time. However, the failure does not occur until the tty is
opened (in rfcomm_dlc_open()).

Because these settings are actually bound at rfcomm device
creation (via RFCOMMCREATEDEV ioctl), validate and fail before
creating the rfcomm tty device.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

RFCOMM tty device teardown can race with new tty device registration
for the same device id:

CPU 0                           | CPU 1
rfcomm_dev_add                  | rfcomm_dev_destruct
                                |   spin_lock
                                |   list_del   <== dev_id no longer used
                                |   spin_unlock
  spin_lock                     |     .
  [search rfcomm_dev_list]      |     .
  [dev_id not in use]           |     .
  [initialize new rfcomm_dev]   |     .
  spin_unlock                   |     .
                                |     .
  tty_port_register_device      |   tty_unregister_device

Don't remove rfcomm_dev from the device list until after tty device
unregistration has completed.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When RFCOMM_RELEASE_ONHUP is set, the rfcomm tty driver 'takes over'
the initial rfcomm_dev reference created by the RFCOMMCREATEDEV ioctl.
The assumption is that the rfcomm tty driver will release the
rfcomm_dev reference when the tty is freed (in rfcomm_tty_cleanup()).
However, if the tty is never opened, the 'take over' never occurs,
so when RFCOMMRELEASEDEV ioctl is called, the reference is not
released.

Track the state of the reference 'take over' so that the release
is guaranteed by either the RFCOMMRELEASEDEV ioctl or the rfcomm tty
driver.

Note that the synchronous hangup in rfcomm_release_dev() ensures
that rfcomm_tty_install() cannot race with the RFCOMMRELEASEDEV ioctl.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

No logic prevents an rfcomm_dev from being released multiple
times. For example, if the rfcomm_dev ref count is large due
to pending tx, then multiple RFCOMMRELEASEDEV ioctls may
mistakenly release the rfcomm_dev too many times. Note that
concurrent ioctls are not required to create this condition.

Introduce RFCOMM_DEV_RELEASED status bit which guarantees the
rfcomm_dev can only be released once.

NB: Since the flags are exported to userspace, introduce the status
field to track state for which userspace should not be aware.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When enumerating RFCOMM devices in the rfcomm_dev_list, holding
the rfcomm_dev_lock only guarantees the existence of the enumerated
rfcomm_dev in memory, and not safe access to its state. Testing
the device state (such as RFCOMM_TTY_RELEASED) does not guarantee
the device will remain in that state for the subsequent access
to the rfcomm_dev's fields, nor guarantee that teardown has not
commenced.

Obtain an rfcomm_dev reference for the duration of rfcomm_dev
access.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

rfcomm_dev_get() can return a rfcomm_dev reference for a
device for which destruction may be commencing. This can happen
on tty destruction, which calls rfcomm_tty_cleanup(), the last
port reference may have been released but RFCOMM_TTY_RELEASED
was not set. The following race is also possible:

CPU 0                            | CPU 1
                                 | rfcomm_release_dev
rfcomm_dev_get                   |   .
  spin_lock                      |   .
    dev  = __rfcomm_dev_get      |   .
    if dev                       |   .
      if test_bit(TTY_RELEASED)  |   .
                                 |   !test_and_set_bit(TTY_RELEASED)
                                 |     tty_port_put   <<<< last reference
      else                       |
        tty_port_get             |

The reference acquire is bogus because destruction will commence
with the release of the last reference.

Ignore the external state change of TTY_RELEASED and instead rely
on the reference acquire itself to determine if the reference is
valid.

Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The tty core supports two models for handling tty_port lifetimes;
the tty_port can use the kref supplied by tty_port (which will
automatically destruct the tty_port when the ref count drops to
zero) or it can destruct the tty_port manually.

For tty drivers that choose to use the port kref to manage the
tty_port lifetime, it is not possible to safely acquire a port
reference conditionally. If the last reference is released after
evaluating the condition but before acquiring the reference, a
bogus reference will be held while the tty_port destruction
commences.

Rather, only acquire a port reference if the ref count is non-zero
and allow the caller to distinguish if a reference has successfully
been acquired.

Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This reverts commit e228b633.

This is the third of a 3-patch revert, together with
Revert "Bluetooth: Remove rfcomm_carrier_raised()" and
Revert "Bluetooth: Always wait for a connection on RFCOMM open()".

Commit 4a2fb3ec,
"Bluetooth: Always wait for a connection on RFCOMM open()" open-codes
blocking on tty open(), rather than using the default behavior
implemented by the tty port.

The reasons for reverting that patch are detailed in that changelog;
this patch restores required functionality for that revert.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This reverts commit 4a2fb3ec.

This is the second of a 3-patch revert, together with
Revert "Bluetooth: Remove rfcomm_carrier_raised()" and
Revert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()".

Before commit cad348a1,
  Bluetooth: Implement .activate, .shutdown and .carrier_raised methods,
tty_port_block_til_ready() was open-coded in rfcomm_tty_install() as
part of the RFCOMM tty open().

Unfortunately, it did not implement non-blocking open nor CLOCAL open,
but rather always blocked for carrier. This is not the expected or
typical behavior for ttys, and prevents several common terminal
programming idioms from working (eg., opening in non-blocking
mode to initialize desired termios settings then re-opening for
connection).

Commit cad348a1,
  Bluetooth: Implement .activate, .shutdown and .carrier_raised methods,
added the necessary tty_port methods to use the default tty_port_open().
However, this triggered two important user-space regressions.

The first regression involves the complicated mechanism for reparenting
the rfcomm tty device to the ACL link device which represents an
open link to a specific bluetooth host. This regression causes ModemManager
to conclude the rfcomm tty device does not front a modem so it makes
no attempt to initialize an attached modem. This regression is
caused by the lack of a device_move() if the dlc is already open (and
not specifically related to the open-coded block_til_ready()).

A more appropriate solution is submitted in
"Bluetooth: Fix unsafe RFCOMM device parenting" and
"Bluetooth: Fix RFCOMM parent device for reused dlc"

The second regression involves "rfcomm bind" and wvdial (a ppp dialer).
rfcomm bind creates a device node for a /dev/rfcomm<n>. wvdial opens
that device in non-blocking mode (because it expects the connection
to have already been established). In addition, subsequent writes
to the rfcomm tty device fail (because the link is not yet connected;
rfcomm connection begins with the actual tty open()).

However, restoring the original behavior (in the patch which
this reverts) was undesirable.

Firstly, the original reporter notes that a trivial userspace
"workaround" already exists: rfcomm connect, which creates the
device node and establishes the expected connection.

Secondly, the failed writes occur because the rfcomm tty driver
does not buffer writes to an unconnected device; this contrasts with
the dozen of other tty drivers (in fact, all of them) that do just
that. The submitted patch "Bluetooth: Don't fail RFCOMM tty writes"
corrects this.

Thirdly, it was a long-standing bug to block on non-blocking open,
which is re-fixed by revert.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This reverts commit f86772af.

This is the first of a 3-patch revert, together with
Revert "Bluetooth: Always wait for a connection on RFCOMM open()" and
Revert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()".

Commit 4a2fb3ec,
"Bluetooth: Always wait for a connection on RFCOMM open()" open-codes
blocking on tty open(), rather than using the default behavior
implemented by the tty port.

The reasons for reverting that patch are detailed in that changelog;
this patch restores required functionality for that revert.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-By: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Now that the LE L2CAP Connection Oriented Channel support has undergone a
decent amount of testing we can make it officially supported. This patch
removes the enable_lecoc module parameter which was previously needed to
enable support for LE L2CAP CoC.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch changes hci_connect_le() so it uses the connection
parameters specified for the certain device. If no parameters
were configured, we use the default values.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds to hdev the connection parameters list (hdev->le_
conn_params). The elements from this list (struct hci_conn_params)
contains the connection parameters (for now, minimum and maximum
connection interval) that should be used during the connection
establishment.

Moreover, this patch adds helper functions to manipulate hdev->le_
conn_params list. Some of these functions are also declared in
hci_core.h since they will be used outside hci_core.c in upcoming
patches.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The LTK key types available right now are unauthenticated and
authenticated ones. Provide two simple constants for it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When the ACL link is using P-256 authenticated combination key, mark
the link mode as HCI_LM_FIPS.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This check is only used for RFCOMM connections and most likely no
RFCOMM based profile will require security level 4 secure connection
security policy. In case it ever does make sure that seucrity level 4
is treated as sufficient security level.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

With support for Secure Connections it is possible to switch the
controller into a mode that is called Secure Connections Only. In
this mode only security level 4 connections are allowed (with the
exception of security level 0 approved services).

This patch just introduces the management command and setting of the
right internal flags to enable this mode. It does not yet enforce it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The struct smp_ltk does not need to be packed and so remove __packed.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The field is not a boolean, it is actually a field for a key type. So
name it properly.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The LTK authenticated parameter is the key type of the LTK and similar
to link keys there is no need to check the currently supported values.

For possible future improvements, the kernel will only use key types
it knows about and just ignore all the other ones.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When encryption for LE links has been enabled, it will always be use
AES-CCM encryption. In case of BR/EDR Secure Connections, the link
will also use AES-CCM encryption. In both cases track the AES-CCM
status in the connection flags.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The function already has an unlock label which means the one extra level
on indentation is not useful and just makes the code more complex. So
remove it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since the use of debug keys can now be identified from the current
settings information, this debugfs entry is no longer necessary.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>