Right now it is possible that serial8250_tx_dma() fails and returns
-EBUSY. The caller (serial8250_start_tx()) will then enable
UART_IER_THRI which will generate an interrupt once the TX FIFO is
empty.
In serial8250_handle_irq() nothing will happen because up->dma is set
and so serial8250_tx_chars() won't be invoked. We end up with plenty of
interrupts and some "too much work for irq" output.

This patch introduces dma_tx_err in struct uart_8250_port to signal that
the last invocation of serial8250_tx_dma() failed so we can fill the TX
FIFO manually. Should the next invocation of serial8250_start_tx()
succeed then the dma_tx_err flag along with the THRI bit is removed and
DMA only usage may continue.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if I boot with console=ttyS0 and the omap driver is module I end up with

| console [ttyS0] disabled
| omap8250 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a 8250
| Unable to handle kernel paging request at virtual address c07a9de0
| Modules linked in: 8250_omap(+)
| CPU: 0 PID: 908 Comm: modprobe Not tainted 3.17.0-rc5+ #1593
| PC is at serial8250_console_setup+0x0/0xc8
| LR is at register_console+0x13c/0x3a4
| [<c0078788>] (register_console) from [<c02d0340>] (uart_add_one_port+0x3cc/0x420)
| [<c02d0340>] (uart_add_one_port) from [<c02d38a4>] (serial8250_register_8250_port+0x298/0x39c)
| [<c02d38a4>] (serial8250_register_8250_port) from [<bf006274>] (omap8250_probe+0x218/0x3dc [8250_omap])
| [<bf006274>] (omap8250_probe [8250_omap]) from [<c02e3424>] (platform_drv_probe+0x2c/0x5c)
| [<c02e3424>] (platform_drv_probe) from [<c02e1eac>] (driver_probe_device+0x104/0x228)
…
| [<c009fa48>] (SyS_init_module) from [<c000e6e0>] (ret_fast_syscall+0x0/0x30)
| Code: 7823603b f8314620 051b3013 491ed416 (44792204)

because serial8250_console_setup() is already gone.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Frans reworded the two comments with better English for better
understanding. His review hit the mailing list after the patch got
applied so here is an incremental update.
Reported-by: NFrans Klaver <frans.klaver@xsens.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In ST16650V2 based serial uarts, while initalizing the PM state,
LCR registers are being initialized to 0 in serial8250_set_sleep().
If console port is already initialized and being used, this will
throws garbage in the console.
Signed-off-by: NSudhir Sreedharan <ssreedharan@mvista.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

serial8250_do_startup() adds UART_IER_RDI and UART_IER_RLSI to ier.
serial8250_stop_rx() should remove both.
This is what the serial-omap driver has been doing and is now moved to
the 8250-core since it does no look to be *that* omap specific.
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Tony noticed that the old omap-serial driver picked the uart "number"
based on the hint given from device tree or platform device's id.
The 8250 based omap driver doesn't do this because the core code does
not honour the ->line argument which is passed by the driver.

This patch aims to keep the same behaviour as with omap-serial. The
function will first try to use the line suggested ->line argument and
then fallback to the old strategy in case the port is taken.

That means the the third uart will always be ttyS2 even if the previous
two have not been enabled in DT.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:

|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
|Control: 10c5387d  Table: 80004019  DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.

NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.

v5…v8:
	- drop RPM from serial8250_set_mctrl() it will be used in
	  restore path which already has RPM active and holds
	  dev->power.lock
v4…v5:
	- add a wrapper around rpm function and introduce UART_CAP_RPM
	  to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
	- added runtime to the console code
	- removed device_may_wakeup() from serial8250_set_sleep()

Cc: mika.westerberg@linux.intel.com
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP UART provides support for HW assisted flow control. What is
missing is the support to throttle / unthrottle callbacks which are used
by the omap-serial driver at the moment.
This patch adds the callbacks. It should be safe to add them since they
are only invoked from the serial_core (uart_throttle()) if the feature
flags are set.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit: e676253b [3/21] serial/8250: Add
support for RS485 IOCTLs, adds a building error on arch m32r.

All error/warnings:

   drivers/tty/serial/8250/8250_core.c: In function 'serial8250_ioctl':
>> drivers/tty/serial/8250/8250_core.c:2859:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
      if (copy_from_user(&rs485_config, (void __user *)arg,
      ^
>> drivers/tty/serial/8250/8250_core.c:2871:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
      if (copy_to_user((void __user *)arg, &up->rs485,
      ^
   cc1: some warnings being treated as errors
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP version of the 8250 can actually use 1:1 serial8250_startup().
However it needs to be extended by a wake up irq which should to be
requested & enabled at ->startup() time and disabled at ->shutdown() time.

v2…v3: properly copy callbacks
v1…v2: add shutdown callback
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no way to access a struct uart_8250_port for a specific
line. This is only required outside of the 8250/uart callbacks like for
devices' suspend & remove callbacks. For those the 8250-core provides a
wrapper like serial8250_unregister_port() which passes the struct
to the proper function based on the line argument.

For run time suspend I need access to this struct not only to make
serial_out() work but also to properly restore up->ier and up->mcr.
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Existing callers of serial8250_modem_status() [1] hold the uart port
lock; document.

[1] In-tree callers of serial8250_modem_status()

drivers/tty/serial/8250/8250_fsl.c
  fsl8250_handle_irq()

drivers/tty/serial/8250/8250_core.c
  serial8250_handle_irq()
  serial8250_console_write()
  serial8250_get_mctrl() *

* Call graphs for callers of serial8250_get_mctrl() from the function
  which acquires the uart port lock

drivers/tty/serial/serial_core.c
  uart_port_startup()
  uart_tiocmget()
  uart_set_termios()
  uart_carrier_raised()
    ops->get_mctrl() ---> serial8250_get_mctrl()
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 06aa82e4.
This commit purports to enable auto CTS flow control for the 8250
UART driver. However, the 8250 UART driver already supports auto
CTS flow control via UART_CAP_AFE and UART_CAP_EFR. Indeed, this
patch introduces another DT attribute for which an existing firmware
flag already exists ("auto-flow-control"). Furthermore, the use of
UPF_HARD_FLOW requires the UART driver to define .throttle and
.unthrottle methods, neither of which are defined for the 8250 UART
driver (which will result in a NULL ptr dereference). Finally, this patch
supposes to fix existing bugs in the serial core for auto CTS-enabled
hardware, but does not include the class of hardware for which these
bugs exist.

CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch allow the users of the 8250 infrastructure to define a
handler for RS485 configration.

If no handler is defined the 8250 driver will work as usual.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
--
v2:Change suggested by Alan "One Thousand Gnomes":
- Move rs485 structure further down on the uart_8250_port structure

 drivers/tty/serial/8250/8250_core.c | 39 +++++++++++++++++++++++++++++++++++++
 include/linux/serial_8250.h         |  3 +++
 2 files changed, 42 insertions(+)
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add flags field to struct kernel_params, and add the first flag: unsafe
parameter. Modifying a kernel parameter with the unsafe flag set, either
via the kernel command line or sysfs, will issue a warning and taint the
kernel.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Jon Mason <jon.mason@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Add tunable RX interrupt trigger I/F of FIFO buffers.

Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.

According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.

This patch makes some devices change RX interrupt trigger from userland.

<How to use>
- Read current setting
 # cat /sys/class/tty/ttyS0/rx_trig_bytes
 8

- Write user setting
 # echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
 # cat /sys/class/tty/ttyS0/rx_trig_bytes
 1

<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)

<Change log>
Changes in V9:
 - Use attr_group instead of dev_spec_attr_group of uart_port structure

Changes in V8:
 - Divide this patch from V7's patch based on Greg's comment

Changes in V7:
 - Add Documentation
 - Change I/F name from rx_int_trig to rx_trig_bytes because the name
   rx_int_trig is hard to understand how users specify the value

Changes in V6:
 - Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
   rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
   UART_FCR_R_TRIG_BITS()
 - Change following function names:
    convert_fcr2val() => fcr_get_rxtrig_bytes()
    convert_val2rxtrig() => bytes_to_fcr_rxtrig()
 - Fix typo in serial8250_do_set_termios()
 - Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
 - Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
   (but UI remains rx_int_trig)
 - Change the meaningless variable name 'val' to 'bytes' following functions:
    fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
    do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
 - Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
   fcr_get_rxtrig_bytes()
 - Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
   in register_dev_spec_attr_grp()
 - Delete the checking whether a user changed FCR or not when minimum buffer
   is needed in serial8250_do_set_termios()

Changes in V5.1:
 - Fix FCR_RX_TRIG_MAX_STATE definition

Changes in V5:
 - Support Tegra, 16650V2, 16654, and 16750
 - Store default FCR value to up->fcr when the port is first created
 - Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
   in convert_fcr2val() and convert_val2rxtrig()

Changes in V4:
 - Introduce fifo_bug flag in uart_8250_port structure
   This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
   for up->bugs. If this flag is enabled, user cannot set RX trigger.
 - Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
   at convert_val2rxtrig()
 - Set the nearest lower RX trigger when users input a meaningless value at
   convert_val2rxtrig()
 - Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
 - Set fcr = up->fcr in the begging of serial8250_do_set_termios()

Changes in V3:
 - Change I/F from ioctl(2) to sysfs(rx_int_trig)

Changed in V2:
 - Use _IOW for TIOCSFIFORTRIG definition
 - Pass the interrupt trigger value itself
Signed-off-by: NYoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It helps to cast struct uart_port to struct uart_8250_port at runtime.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.

SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
  "If IGNBRK is set, a break condition detected on input shall be ignored;
   that is, not put on the input queue and therefore not read by any
   process."

Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.

Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio

Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom

Annotated for fixes:
altera_uart
mcf

Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial

Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core

Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: NIvan <athlon_@mail.ru>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In (efe2f29e kgdboc,kdb: Allow kdb to work on a non open console port)
support was added to directly use the "write_char" functions when
doing kdb over a non-open console port.  This is great, but it ends up
bypassing the normal code in uart_console_write() that adds a carriage
return before any newlines.

There appears to have been a trend to add this support directly in
some console driver's poll_put_char() functions.  This had a few side
effects, including:
- In this case we were doing LFCR, not CRLF.  This was fixed in
  uart_console_write() back in (d358788f [SERIAL] kernel console should
  send CRLF not LFCR)
- Not all serial drivers had the LFCR code in their poll_put_char()
  functions.  In my case I was running serial/samsung.c which lacked
  it.

I've moved the handling to uart_poll_put_char() to fix the above
problems.  Now when I use kdb (and don't point console= to the same
UART) I no longer get:

[0]kdb>
       [0]kdb>
              [0]kdb>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On transmit-hold-register empty, serial8250_tx_chars
should be called only if we don't use DMA.
DMA has its own tx cycle.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit f4f653e9.

Jiri writes:
	No, please drop this one. We need a better solution as it turned
	out that some boxes need 16k loops and it will increase with new
	processors :(.

Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Martin Pluskal <mpluskal@suse.com>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The 8250 driver now reports many of these:
  serial8250: too much work for irq4
These messages turned out to be common these days with a use of
virtualization. I tried to increase the limit of processed characters
in commit e7328ae1 (serial: 8250,
increase PASS_LIMIT) in 2011. It was raised from 256 to 512, but it is
still not enough, apparently.

So disable the warning unless somebody turns on DEBUG (or
DYNAMIC_DEBUG _and_ the message).
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Reported-by: NMartin Pluskal <mpluskal@suse.com>
Reported-by: NTakashi Iwai <tiwai@suse.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
References: https://bugzilla.novell.com/show_bug.cgi?id=868394Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In -RT the spin_lock_irqsave() does not spin but sleep if the lock is
taken. Before that, local_irq_save() is invoked which disables
interrupts even on -RT. Therefore local_irq_save() + spin_lock() does not
work.
In the ->sysrq and oops_in_progress case it is save to trylock the lock
i.e. this is what we do now anyway except for ->sysrq where we assume
that the lock is already taken.

The spin_lock_irqsave() grabs the lock and disables the interrupts on
vanilla (the same behavior) and on -RT it won't disable interrupts.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
[bigeasy: add a patch description]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Every couple of months, someone sends a patch to fix:

drivers/tty/serial/8250/8250_core.c: In function 'serial_unlink_irq_chain':
drivers/tty/serial/8250/8250_core.c:1712:2: warning: 'i' may be used uninitialized in this function [-Wuninitialized]

and they in turn get a NACK for their efforts, and are told that
their compiler is broken.  This has been going on since at least
the year 2008:  https://lkml.org/lkml/2008/11/24/433

Lets add a comment, so that subsequent patches don't get as far as
the maintainers or the mailing lists.
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Exar XR17V35x family of UARTs have an additional fractional divisor
register (DLD) which was not being used. Calculate and set this
register for these devices to reduce their baud rate error.
Signed-off-by: NJoe Schultz <jschultz@xes-inc.com>
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.

When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:

    irq 68: nobody cared (try booting with the "irqpoll" option)

In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.

In practice, this is not needed under any of the following conditions:

* On Tegra chips after Tegra30, since the HW bug has apparently been
  fixed.

* On UARTs C..E since their MODEM control signals are tied to the correct
  static state which doesn't trigger the issue.

* On UARTs A..B if the MODEM control signals are routed out to package
  pins, since they will then carry valid signals.

However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.

Reported-by: Olof Johansson <olof@lixom.net> # autotester
Cc: <stable@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

DMA engines usually expect the fifo trigger level to be
aligned with the burst size. It should not be changed even
with small baud rates. This will fix an issue with
Designware DMA engine where the data can not be transferred
over UART with lower baud rates then 2400.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit cfcec52e.

This regresses a longstanding behaviour on X86 systems, which end up with
PCI serial ports moving between ttyS4 and ttyS0 when you bisect to opposite
sides of this commit, resulting in the need to constantly modify the console
setting in order to bisect across it.

Please revert, we can work on solving this for ARM platforms in a less
disruptive way.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>
Cc: Karthik Manamcheri <karthik.manamcheri@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

They were introduced by mistake in 3.7. Let's deprecate them now. For
the reasons, see the text in Kconfig below.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In 3.7 the 8250 module name was changed unintentionally from 8250 to
8250_core by commit 835d844d
(8250_pnp: do pnp probe before legacy probe). We then had to
re-introduce the old module options to ensure the old good
8250.nr_uart & co. still work. This can be done only by a very dirty
hack and we did it in f2b8dfd9
(serial: 8250: Keep 8250.<xxxx> module options functional after driver
rename).

That is so damn ugly so that I decided to revert to the old module
name and deprecate the new 8250_core options present in 3.7 and 3.8
only. The deprecation will happen in the following patch.

Note that this patch changes the hack above to support "8250_core.*",
because we now have "8250.*" natively.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In most cases the tx_loadsz is the same as fifosize. This
will store the fifosize in it if it was not separately
delivered from the driver.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With commit 835d844d (8250_pnp: do pnp probe before legacy probe), the
8250 driver was renamed to 8250_core.  This means any existing usage of
the 8259.<xxxx> module parameters or as a kernel command line switch is
now broken, as the 8250_core driver doesn't parse options belonging to
something called "8250".

To solve this, we redefine the module options in a dummy function using
a redefined MODULE_PARAM_PREFX when built into the kernel.  In the case
where we're building as a module, we provide an alias to the old 8250
name.  The dummy function prevents compiler errors due to global variable
redefinitions that happen as part of the module_param_ macro expansions.
Signed-off-by: NJosh Boyer <jwboyer@redhat.com>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for Altera 8250/16550 compatible serial port.
Signed-off-by: NLey Foon Tan <lftan@altera.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The MIPS based Ralink WiSoC platform has 1 or more 8250 compatible serial cores.
To make them work we require the same quirks that are used by AU1x00.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).

This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts.  The UART_CAP_HFIFO
capability was added to track this.  It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: NStephen Hurd <shurd@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for dmaengine API. The drivers can implement the
struct uart_8250_dma member in struct uart_8250_port and
8250.c can take care of the rest.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>