Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per measurements, the SFP+ suffered from small current leakage in two cases:
 - When no module was plugged and TX laser was disabled. The fix was to enable
   it, and when module is plugged in, check if it needs to be disabled.
 - When over-current event occurs due to invalid SFP+ module, the HW basically
   shuts down the current for this module, but the SW needs to complete this
   by issuing a power down via a GPIO.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When drivers works on top of an old bootcode, it is theoretically subjected to
MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence,
rather than per CL45 command. On rare cases an old bootcodes may change that in
the middle, so to address that, the MDIO clock is set for each CL45 access.
In addition, setting the MDIO clock is now done per EMAC base, and
not per port number, since a specific port can potentially use both EMACs for
different PHY accesses.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case Link Flap Avoidance feature is supported by the MCP, bnx2x will enable
it, and will pass the appropriate parameter when load request is sent to
the MCP.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix bug where a register which was only meant to be read in 578xx/57712
devices causes a bogus error message to be logged when read from other
devices.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x_hsi.h was included twice.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds static declaration to several functions in bnx2x. It eliminates
newly introduced sparse warnings reported by Fengguang Wu.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the BCM_CNIC define with a flag which can change at run-time
and which does not use the CONFIG_CNIC kconfig option.
For the PF/hypervisor driver cnic is always supported, however allocation of
cnic resources and configuration of the HW for offload mode is done only when
the cnic module registers bnx2x.
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the driver-FW HSI to support changes to the 'update' ramrod
(FW supports this change since 7.8.2). This ramrod is sent when the cnic module
registers bnx2x, to enable changing the nic_mode configuration in HW at
run-time.
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct spelling typo in bnx2x driver
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of link flap avoidance between PXE boot and bnx2x, set the appropriate
PHY DEVAD even if LFA kicks in.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 1G KR link by restoring CL72 misc control register to default value rather
than 0.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit a3348722 AFEX FCoE function is continuously reset.
The patch prevents the resetting and removes debug print
to stop garbaging syslog.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d760fc37 caused
1G functions to allocate rx rings which were 1/10 of the
size of 10G functions' rx rings.

However, it also caused 10G functions on 5771x boards to
allocate small rings, which limits their possible (default)
rx throughput. This patch causes all 10G functions to use
rings of intended length by default.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DRV_MODULE_VERSION is smaller than the ->version buffer so the memcpy()
copies 1 byte past the end of the string.  It's not super harmful, but
it makes the static checkers complain.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the bnx2x and cnic drivers into using FW 7.8.2
which was recently submitted into the linux-firmware tree.

A short summary of minor bugs fixed by this FW:
 1. In switch dependent mode, fix several issues regarding inner vlan
    vs. DCB priorities.
 2. iSCSI - not all packets were completed on a forward channel.
 3. DCB - fixed for 4-port devices.
 4. Fixed false parity reported in CAM memories when operating near -5%
    on the 1.0V core supply.
 5. ETS default settings are set to fairness between traffic classes
    (rather than strict priority), and uses the same chip receive buffer
    configuration for both PFC and pause.

For a complete list of fixes made by this FW, see commit 236367db
in the linux-firmware git repository.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the definition of bnx2x_tests_str_arr from static char
pointer to static const char bi-directional array. Also the
bnx2x_get_strings function is simplified.
Reported-by: NJoe Perches <joe@perches.com>
Reported-by: NDavid Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since version 7.4 the FW configures in the pci config space the max
number of interrupts available to the physical function, instead of
the exact number to use.
This causes a false warning in driver when comparing the number of
configured interrupts to the number about to be used.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d6cb3e41 "bnx2x: fix checksum validation" caused a performance
regression for IPv6. Rx checksum offload does not work. IPv6 packets
are passed to the stack with CHECKSUM_NONE.

The hardware obviously cannot perform IP checksum validation for IPv6,
because there is no checksum in the IPv6 header. This should not prevent
us from setting CHECKSUM_UNNECESSARY.

Tested on BCM57711.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a3348722 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).

This patch adds the missing segments, fixing said issues.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.

This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change various flows in the bnx2x driver which up until now flapped
the link - these flows now benefit from the link flap avoidance mechanism.

This includes the removal of the link reset made upon nic init, as it is
possible the link is already active at that time.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Various flows in the bnx2x driver cause a link-flap - if the link
is up, it would be toggled down (after a mac/phy reset) and then
taken back up.

In many of these cases, there is no need to do cause such a flap,
as the associated flows should not actually affect the link.

This patch adds the 'Link Flap Avoidance' mechanism, which allows
the driver to better determine if a given flow requires a link change,
and thus minimize the number of link flaps caused by the driver.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate the interrupt setting part of each external PHY to a specific
function.
This allows calling the interrupt setting in case of link-flap avoidance,
since some link owners may not enable the interrupt on their own.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables boards with 54618SE phys and a sufficiently new
firmware to use native EEE instead of auto-greeen.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to lay the foundation for 1G EEE support, several segments of code
which are common to both 1G and 10G EEE configurations were extracted from
the 10G EEE configuration flow to their own functions.
E.g., bnx2x_eee_initial_config, bnx2x_eee_advertise, bnx2x_eee_disable, etc.

The rest of the EEE functions were relocated and placed in a single,
continuous section of the file.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>