It seems to be relatively common for USB keyboards and mice to dislike
being polled for reports.  Since there's no need to poll a keyboard or
a mouse, this patch (as685) automatically sets the HID_QUIRK_NOGET flag
for devices that advertise themselves as either sort of device with boot
protocol support.

This won't cure all the problems since some devices don't support the
boot protocol, but it's simple and easy and it should fix quite a few
problems.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB HID/HIDBP, INPUT DRIVERS: fix various usb/input/hid-input.c bugs that make Apple Mighty Mouse work poorly

Transposed lines of code in drivers/usb/input/hid-input.c causes the
capability bits for a new HID device to be set before quirks are applied
at configuration time.  When an HID event is then sent up to the input
layer, it may then be discarded as irrelevant because the wrong
capability bit is set.

Further, the quirks for the Apple Mighty Mouse are not quite right: the
horizontal scrolling needs its axis reversed, and the left and center
buttons are transposed.  Also, the mouse is labeled in the kernel with
its earlier name (I think) of Apple PowerMouse.

Steps to reproduce problem: Plug in an Apple Mighty Mouse.  Note that
horizontal scrolling doesn't work at all, and in fact doesn't generate
any input events on /dev/input/eventN.  Note also that pushing the
middle button performs the right button action, and vice versa.  Once
you have the horizontal scrolling working, note that it is backward WRT
both to vertical scrolling and to common sense.

This patch maybe should be broken up, as it does address two problems.
The transposed code in hidinput_configure_usage() probably creates bugs
beyond just the Mighty Mouse.  The rest of the patch renames POWERMOUSE
to MIGHTYMOUSE everywhere (which I *believe* is correct), fixes the
MIGHTYMOUSE quirk to swap the center and right mouse buttons, and adds a
new quirk HID_QUIRK_INVERT_HWHEEL also assigned to the MIGHTYMOUSE with
code in hidinput_hid_event() to implement it.
Signed-off-by: NBart Massey <bart@cs.pdx.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as676) fixes a small bug in uhci-hcd's enqueue routine.  When
an URB is unlinked or gets an error and the completion handler queues
another URB for the same endpoint, the queue shouldn't be allowed to start
up again until the handler returns.  Not even if the new URB is the only
one on its queue.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as675) simplifies uhci-hcd slightly by storing each endpoint's
type in the corresponding Queue Header structure.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The net2280 board has an annoying habit of surviving soft reboots with
interrupts enabled.  This patch (as674) adds a shutdown routine to the
driver so that the board can be put in a quiescent state.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Unfortunately it looks like the transport entry for this subdriver was merged
into the protocol section, making this driver unusable :(
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After some further testing with my flash device I realised that our current
probe doesn't always work (e.g. when no media is inserted).

Now that Peter Chubb's patch has simplified the detection of 99% of the HP CD
writers out there, we have a much smaller range of hardware to work with on
the shared device ID, so it should be possible to try some of the previous
probe options again: we just need to find another tester with a USBAT2-based HP
CD writer.

This patch hardcodes the flash detection until someone comes along with one of
these obscure CD drives. Note that these devices are extremely rare, so even if
we can't ever find a decent probe method, at least we will be supporting almost
all of the USBAT-based hardware out there.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use USB vendor and product IDs to determine whether the attached
device is a CDROM or a Flash device.  Daniel Drake says that the
*same* vendor and product IDs for non-HP vendor ID could be either
flash or cdrom, so try to probe for them.
Signed-off-by: NPeter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've worked out what's going wrong.  The scsi layer is now much
more likely to pass down scatterlists instead of plain buffers.  So
you have to make sure that they're handled correctly.  In one of the
changes along the way, usbat_write_block and friends stopped obeying
the srb->use_sg flag.

Anyway, with the appended patch, and the one I'm putting in the next email, it
all seems to work for the HP cd4e.  Of course, someone's going to have
to test it with the flash drives as well....

This patch teaches the usbat_{read,write}_block functions to
obey the use_sg flag in the scsi-request.
Signed-off-by: NPeter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make inputs pollable using sysfs_notify and add support for the Phidget
InterfaceKit 0/16/16. Various cleanups.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NDaniel Saakes <daniel@saakes.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We #include <linux/netdevice.h> only because <linux/etherdevice.h>
needed it, but didn't #include it itself.  But that's been fixed now.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove pointless inline.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove the check for NULL which makes no sense. Suggested by Al.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some hubs claim not to support port-power switching, and right now the
hub driver believes them and does not enable power to their ports.
However it turns out that even though they don't actually switch power,
they do ignore all events on a port until told to turn on the power!
This problem has been reported by several users.

This revised patch (as672b) makes the hub driver always try to turn on
port power to all hubs, regardless of what the hub descriptor says.  It
also adds a comment explaining the need for this.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for MacBook touchpad in appletouch driver.
Thanks to Alex Harper for the informations.

Use u16 instead of int16_t in atp_is_geyser* functions.
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NStelian Pop <stelian@popies.net>
Signed-off-by: NNicolas Boichat <nicolas@boichat.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Prevent sending further output to a USB-serial console after the dongle is
disconnected, take care not to leak kref.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Prevent ENODEV on a /dev/ttyUSBx, used as a USB-serial console.

From: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Prevent NULL dereference when used as a USB-serial console.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Append Carriage-Returns after Line-Feeds, analogous to the serial driver.

From: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In some systems we may have both a platform EHCI controller and PCI EHCI
controller.  Previously we couldn't build the EHCI support as a module due
to conflicting module_init() calls in the code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains the following possible cleanups:
- make needlessly global functions static
- function and struct declarations belong into header files
- make SiS_VCLKData const
- #if 0 the following unused global functions:
  - sisusb.c: sisusb_writew()
  - sisusb.c: sisusb_readw()
  - sisusb_init.c: SiSUSB_GetModeID()
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Arjan van de Ven <arjan@infradead.org>

Convert the semaphores-used-as-mutex to mutexes in the sisusb video driver;
this required manual checking due to the "return as locked" stuff in this
driver, but the ->lock semaphore is still used as mutex in the end.
Signed-off-by: NArjan van de Ven <arjan@infradead.org>
Cc: Thomas Winischhofer <winischhofer.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for detection and dworking with a ASIX 88178 based USB-Gigabit
adaptor.  With the patch, it is detected and handled correctly by the asix
module.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This includes an MTU fixup which could affect larger packets with newer
Zaurii, described as http://bugzilla.kernel.org/show_bug.cgi?id=6286;
plus minor whitespace cleanup.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this fixes the "duplicated text" bug. There's a modem that cannot cope
with large transfers and more than one urb in flight. This patch adds a
special case to the driver.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Keys on Yealink based phones will not function properly when using the
generic HID driver. This patch prevents the generic HID code from
grabbing the device before the regular yealink driver can get a grip on
it.
Signed-off-by: NHenk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Paul Serice <paul@serice.net>

The workaround in commit f7201c3d
broke.  The work around requires memory for DMA transfers for some
NVidia EHCI controllers to be below 2GB, but recent changes have
caused some DMA memory to be allocated before the DMA mask is set.
Signed-off-by: NPaul Serice <paul@serice.net>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

During the recent "isa drivers using platform devices" discussion it was
pointed out that (ALSA) ISA drivers ran into the problem of not having
the option to fail driver load (device registration rather) upon not
finding their hardware due to a probe() error not being passed up
through the driver model. In the course of that, I suggested a seperate
ISA bus might be best; Russell King agreed and suggested this bus could
use the .match() method for the actual device discovery.

The attached does this. For this old non (generically) discoverable ISA
hardware only the driver itself can do discovery so as a difference with
the platform_bus, this isa_bus also distributes match() up to the driver.

As another difference: these devices only exist in the driver model due
to the driver creating them because it might want to drive them, meaning
that all device creation has been made internal as well.

The usage model this provides is nice, and has been acked from the ALSA
side by Takashi Iwai and Jaroslav Kysela. The ALSA driver module_init's
now (for oldisa-only drivers) become:

static int __init alsa_card_foo_init(void)
{
	return isa_register_driver(&snd_foo_isa_driver, SNDRV_CARDS);
}

static void __exit alsa_card_foo_exit(void)
{
	isa_unregister_driver(&snd_foo_isa_driver);
}

Quite like the other bus models therefore. This removes a lot of
duplicated init code from the ALSA ISA drivers.

The passed in isa_driver struct is the regular driver struct embedding a
struct device_driver, the normal probe/remove/shutdown/suspend/resume
callbacks, and as indicated that .match callback.

The "SNDRV_CARDS" you see being passed in is a "unsigned int ndev"
parameter, indicating how many devices to create and call our methods with.

The platform_driver callbacks are called with a platform_device param;
the isa_driver callbacks are being called with a "struct device *dev,
unsigned int id" pair directly -- with the device creation completely
internal to the bus it's much cleaner to not leak isa_dev's by passing
them in at all. The id is the only thing we ever want other then the
struct device * anyways, and it makes for nicer code in the callbacks as
well.

With this additional .match() callback ISA drivers have all options. If
ALSA would want to keep the old non-load behaviour, it could stick all
of the old .probe in .match, which would only keep them registered after
everything was found to be present and accounted for. If it wanted the
behaviour of always loading as it inadvertently did for a bit after the
changeover to platform devices, it could just not provide a .match() and
do everything in .probe() as before.

If it, as Takashi Iwai already suggested earlier as a way of following
the model from saner buses more closely, wants to load when a later bind
could conceivably succeed, it could use .match() for the prerequisites
(such as checking the user wants the card enabled and that port/irq/dma
values have been passed in) and .probe() for everything else. This is
the nicest model.

To the code...

This exports only two functions; isa_{,un}register_driver().

isa_register_driver() register's the struct device_driver, and then
loops over the passed in ndev creating devices and registering them.
This causes the bus match method to be called for them, which is:

int isa_bus_match(struct device *dev, struct device_driver *driver)
{
          struct isa_driver *isa_driver = to_isa_driver(driver);

          if (dev->platform_data == isa_driver) {
                  if (!isa_driver->match ||
                          isa_driver->match(dev, to_isa_dev(dev)->id))
                          return 1;
                  dev->platform_data = NULL;
          }
          return 0;
}

The first thing this does is check if this device is in fact one of this
driver's devices by seeing if the device's platform_data pointer is set
to this driver. Platform devices compare strings, but we don't need to
do that with everything being internal, so isa_register_driver() abuses
dev->platform_data as a isa_driver pointer which we can then check here.
I believe platform_data is available for this, but if rather not, moving
the isa_driver pointer to the private struct isa_dev is ofcourse fine as
well.

Then, if the the driver did not provide a .match, it matches. If it did,
the driver match() method is called to determine a match.

If it did _not_ match, dev->platform_data is reset to indicate this to
isa_register_driver which can then unregister the device again.

If during all this, there's any error, or no devices matched at all
everything is backed out again and the error, or -ENODEV, is returned.

isa_unregister_driver() just unregisters the matched devices and the
driver itself.

More global points/questions...

- I'm introducing include/linux/isa.h. It was available but is ofcourse
a somewhat generic name. Moving more isa stuff over to it in time is
ofcourse fine, so can I have it please? :)

- I'm using device_initcall() and added the isa.o (dependent on
CONFIG_ISA) after the base driver model things in the Makefile. Will
this do, or I really need to stick it in drivers/base/init.c, inside
#ifdef CONFIG_ISA? It's working fine.

Lastly -- I also looked, a bit, into integrating with PnP. "Old ISA"
could be another pnp_protocol, but this does not seem to be a good
match, largely due to the same reason platform_devices weren't -- the
devices do not have a life of their own outside the driver, meaning the
pnp_protocol {get,set}_resources callbacks would need to callback into
driver -- which again means you first need to _have_ that driver. Even
if there's clean way around that, you only end up inventing fake but
valid-form PnP IDs and generally catering to the PnP layer without any
practical advantages over this very simple isa_bus. The thing I also
suggested earlier about the user echoing values into /sys to set up the
hardware from userspace first is... well, cute, but a horrible idea from
a user standpoint.

Comments ofcourse appreciated. Hope it's okay. As said, the usage model
is nice at least.
Signed-off-by: NRene Herman <rene.herman@keyaccess.nl>

This patch (as721) makes dev_info and related macros print the device's
bus name if the device doesn't have a driver, instead of printing just a
blank.  If the device isn't on a bus either... well, then it does leave
a blank space.  But it will be easier for someone else to change if they
want.

Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need to create the "compatible" symlinks that class_devices used to
create when they were in the class directories so that userspace does
not know anything changed at all.

Yeah, we have a lot of symlinks now, but we should be able to get rid of
them in a year or two... (wishful thinking...)
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Like the SUBSYTEM= key we find in the environment of the uevent, this
creates a generic "subsystem" link in sysfs for every device. Userspace
usually doesn't care at all if its a "class" or a "bus" device. This
provides an unified way to determine the subsytem of a device, regardless
of the way the driver core has created it.
Signed-off-by: NKay Sievers <kay.sievers@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is the first step in moving class_device to being replaced by
struct device.  It allows struct device to export a dev_t and makes it
easy to dynamically create and destroy struct device as long as they are
associated with a specific class.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is needed for a future patch for the device code to create the
proper symlinks for devices that are "class devices".
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hi, this patch converts semaphores to mutexes for Randy's firmware_class.
Signed-off-by: NLaura Garcia Liebana <nevola@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This makes the driver model PM suspend debug messages more useful, by

  (a) explaining what event is being sent, since not all suspend()
      requests mean the same thing;

  (b) reporting when a PM_EVENT_SUSPEND call is allowing the device
      to issue wakeup events.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To have a home for all hypervisors, this patch creates /sys/hypervisor.
A new config option SYS_HYPERVISOR is introduced, which should to be set
by architecture dependent hypervisors (e.g. s390 or Xen).
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

platform_device_add() should be using device_add() rather
than device_register() - any platform device passed to
platform_device_add() should have already been initialised,
either by platform_device_alloc() or platform_device_register().
Signed-off-by: NRussell King <rmk@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

allow sysdev_class adding attribute. Next patch will use the new API to
add an attribute under /sys/device/system/cpu/.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds modalias support to platform devices, for simpler
hotplug/coldplug driven driver setup.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>